****LOW COST SHIPPING TO CANADA*****
****FREE SHIPPIING LOWER 48 STATES****
My Account
Login
Register
Call us (630) 675-4509
Cart
($0.00)
0
No products in the cart.
Return To Shop
Shopping cart (0)
Subtotal: $0.00
Free shipping Lower 48 States
****LOW COST SHIPPING TO CANADA*****
****FREE SHIPPIING LOWER 48 STATES****
Show
Filter by
Filter by
Filter by
6007 Wet Condition Epoxy For Concrete & Steel | Low Temp 35°F
From: $575.00- Protect Problem Wet and Damp Areas
- Withstands to 20 PSI Hydralic Vapor Pressure
- Cold temperature down to 35°F
- Designed to Protect both Concrete and Steel
- Use as Primer With Topcoat or Floor Coating
- Offers Excelllent Moisture and Corrosive Protection with Outstanding Adhesion
- 100% Solids, no VOC, 2 Component
6009 Epoxy Floor Coating Industrial & Commercial Low Temp 35°F | 100% Solids | Quick Cure
From: $110.00- Commercial, Industrial, Residential Concrete Floors
- Cold temperature down to 35°F
- Tough - Attractive Looking Epoxy
- Good Chemical, Abrasion, Impact Resistance
- Quick 4 to 7 hour set time
- Self Priming With No Primer Required
- 100% Solids, no VOC, 2 Component
- Clear or Selection of Colors
- Excellent Protection at Lower Cost
6012-2F Epoxy Grout & Concrete Floor Coating | Cold Damp 35°F | FAA-P606 Airfield
From: $205.00- Fast Set for Cold Temp and Damp Conditions
- Cold temperature down to 35°F
- Moisture Tolerant
- Superior Corrosive Water & Acid Resistance
- For Industrial Floors With Full Sand Broadcast
- Works Great as an Epoxy Grout
- Used in Petrochemical, Airfield Lighting, Waste Holding areas, Concrete Repair
- Meets FAA-P6606 Requirements for use on Airfields
- 100% Solids, no VOC, 2 Component
6012-2S Epoxy Primer / Grout Slow Set For Warm & Damp
From: $205.00- High Performance Slow Set Epoxy Primer & Grout
- Protects Concrete and Steel
- Apply in Difficult Warm and Damp Conditions
- Great Bonding Primer For Urethane & Polyurea Topcoats
- Superior Chemical and Moisture Protection
- 100% Solids, no VOC, 2 Component
AM1016 Anti-Microbial Mildew Resistant Anti-Slip Epoxy Floor Coating – 3 Gal Kit
From: $210.00- Adds slip resistant finish to concrete floors
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Good for surfaces subject to bare foot traffic
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical and abrasion resistance
- Wide selection clear plus 20 colors
- Water base
AM253 Novolac Anti-Microbial Epoxy Resists Mildew Growth Acid Solvent Chemicals
From: $398.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Resists high concentration acids, some chlorinated solvents incl xylene, MEK
- High build for heavy duty traffic, chemical troughs, curbs
- Great for tanks, chemical spill areas
- Works on cement, masonry or brick
- Excellent adhesion 425 psi
- Quick back in-service, light foot traffic 10-18 hrs
- Low voc 47 g/L
AM257P Novolac Primer Anti-Microbial Epoxy Resists Mildew Growth Acid Solvent Chemicals
From: $325.52- Outstanding Spill & Splash Acid, Solvent, Chemical surface protection
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Excellent primer companion to AM253 Novolac Anti-Microbial Epoxy
- Resists wide range of chemicals, solvents, acids
- Excellent adhesion 375 psi
- Long working time 1 to 3 hour POT life
- Selection of 3 color options
AM5015 Anti-Microbial Mildew Resistant Epoxy Primer WB
From: $94.00- Versatile epoxy primer for concrete, masonry, wood
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Available 20 Colors To Match Topcoat
- Excellent primer for epoxy, polyaspartic, urethane
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical & abrasion resistance
- Water base
AM707HB Anti-Microbial Mildew Resistant Epoxy Floor Coating | 100% Solids
From: $162.00- High Build - 100% Solids Commercial Epoxy
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Long POT Life (working time) 30-50 min
- Excellent Adhesion 450 psi
- Abrasion resistant Only 32 mg loss (Tabor test)
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
- Wide Variety of 20 Different Colors
DT-454 Epoxy Quick Cure UV Concrete Floor Coating Low Temp 40F | 100% Solids
From: $67.00- Tough, Durable Epoxy Coating
- Quick cure 6-7 hour recoat time
- Outstanding Bonding
- UV Resistant
- Good chemical, impact and abrasion resistance
- Cold temperature application down to 40F
- High solids 100%
- Available in clear & 14 colors! (Pigment sold separately)
E-Poly Pigment For All Floorguard Epoxy & Polyaspartic Coatings
From: $52.00- Universal E-Poly Pigment Designed to Color All Epoxy & Polyaspartic Coatings manufactured by Floorguard Products
- Add a Beautiful Decorative Color to Your Epoxy Project
- 14 Different Colors to Choose From!
- Sold in Quart Containers - Typically colors 3-5 Gallons When Mixed Into Clear Epoxy or Polyaspartic
- Pigment can be Pre-mixed into Floorguard Epoxy & Polyaspasrtic Coatings on all orders 60 gallons or more with 4-7 days lead time (when ordered in 10 or 15 gallon kits as appropriate)
E1000 Epoxy Concrete Repair Kit | Holes to 1″ | Cracks | Spall | 3 Color
$135.00- Make quick, permanent repairs to concrete
- Patch cracks, spalled concrete and potholes
- Can be applied at ¼” – 1” thickness
- Outstanding adhesion to concrete
- Excellent chemical, abrasion and impact resistance
- USDA approved for food processing plants
- Easy to mix and apply
- 3 Colors Packaged in a 5 gallon pailConcret
E100V Vertical Wall High Build Epoxy Coating | To 12 Mils No Sag | 12 Colors | Underwater Concrete
From: $50.00- No sagging on vertical walls to 12 mils per coat
- Good chemical and abrasion resistance
- Works well on underwater concrete decorative surfaces including pools and water features
- Long 45 - 90 min pot life
- Outstanding adhesion 475 psi @elcometer
- Wide selection of 12 color options
- 100% solids, very low voc
E1015V Vertical Wall Epoxy Coating & Primer to 8 Mils No Sag | 11 Colors
From: $50.00- No sagging on vertical walls up to 8 mils per coat
- Good for priming or coating concrete, wood or masonry.
- Good chemical and abrasion resistance
- Long 1 - 1.5 hour pot life
- Excellent adhesion 425 psi @elcometer
- Wide selection of 11 color options
- Water base
E1016 Anti-Slip Epoxy Concrete Floor Coating – 3 Gal Kit
From: $196.00- Adds a slip resistant finish to concrete floors
- Good for use on surfaces subject to bare foot traffic
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical and abrasion resistance
- Wide selection of clear plus 20 color options
- Water base
E105M Epoxy Mortar Concrete Resurfacer & Patch Kit
From: $66.00- Economical Easy resurfacing old and damaged concrete floors
- Compressive Strength 8,400 psi ASTM D695
- Heat Deflection Temp 131.7F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- 100% solids epoxy
- Comes complete with epoxy & aggregate
- Selection of 5 color options
- Application temp range 55°F to 90°F
E110M Epoxy Mortar Concrete Premium Resurfacer & Patch Kit
From: $73.00- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- 10% greater coverage/unit vs E105M Epoxy Mortar
- Compressive Strength 11,150 psi ASTM D695
- Heat Deflection Temp 158.9F ASTM D648
- High Build Resurfacing 1/8" to 1"
- Spot Patching up to 2" - 3" thick
- Long 30-40 min POT Life
- 100% solids epoxy
- Comes complete with epoxy and aggregate
- Selection of 5 color options
- Application temp range 55°F to 90°F
E126CW Cold Weather Epoxy Mortar Concrete Resurfacer & Patch Kit 35°F to 80°F
From: $71.00- Great for Cold Weather & Cold Storage Facilities
- Application range 35°F to 80°F
- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- Compressive Strength 11,284 psi ASTM D695
- Heat Deflection Temp 149.9F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- 100% solids epoxy
- Comes complete with epoxy and aggregate
- Selection of 5 color option
E128AF Arctic Epoxy Mortar Concrete Patch Kit | Cold Condition -10°F to 40°F
From: $70.00- Tough, Durable Cold Winter Weather Concrete Patch & Repair
- Excellent Extreme Cold Condition Patching -10°F to 40°F
- Great For Freezer, Cold Storage and Outdoor Winter Repairs
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- Excellent chemical resistance
- Excellent Abrasion and Impact Resistance
- Compressive Strength 11,000 psi ASTM D695
- Quick recoat 1-2 hrs & 2-4 hrs light foot traffic
- Selection of 3 color options
- Easy to Use 3 part kit Includes Silica Sand or Liquid Only
E130A Oil Contaminated Concrete & Asphalt Epoxy Mortar Patch Kit/Resurfacer
From: $66.00- Great for patching and repairing oil contaminated and damaged concrete
- Can be used to patch and repair asphalt surfaces
- Can be applied up to 1/8" one application
- Crack. holes and general surface repairs
- Excellent abrasion and impact resistance
- 100% solids
- Easy to Use 3 part kit Includes Silica Sand or Liquid Only
E1409CL Moisture Vapor Barrier Epoxy Sealer Primer For Concrete ASTM F3010
From: $247.00- Reduce effects of moisture vapor transmission on concrete floors
- Control moisture vapor emission rates to 20 lb/24hr/1000 sq' (ASTM F1869)
- Used as Sealer/Primer to protect Polymeric coating systems, vinyl sheets, tile, cementitious overlays, terrazo, wood veneers, and carpet
- 100% solids with 0 voc
- Easy to apply with one coat most projects
- Meets ASTM F3010 for vapor permeance at the recommended thickness
E1500HN Novolac Epoxy | Superior Steel & Concrete Chemical Horizontal Protection | Secondary Co...
$325.00- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
- Great horizontal chemical protection for Secondary Containment for both steel and concrete surfaces
- Thin film self leveling to 40 mils DFT one coat
- Extremely tough with high wearing properties
- Excellent abrasion resistance and impact resistance
- Meets USDA requirements
E15M Epoxy Mastic Steel Primer DTM & Concrete Coating | Chemical Resistant | Low Temp 25F
From: $95.00- High solids DTM (direct-to-metal) chemical resistant steel primer or finish coat to steel and concrete
- Self priming to steel including tight rust
- Apply Vertical Surfaces to 8 mils DFT Steel & Concrete
- Great primer for use with our E1500HN (horizontal) and E555VN (vertical) Novolac Chemical Resistant Epoxies
- USDA Approved
- Tight film, low permeability.
- Exceptional adhesion Exceeds 500 psi
- Excellent impact resistance 90 in lb
- Excellent abrasion resistance CS 17 Wheel, 1000 cycles, 1000 g Load 21 mg loss
- Excellent against rust “undercutting”
- Easy to apply brush, roll and spray
- Low temp cure version to 25°F
- Available 13 colors
E183HB Epoxy Floor Coating High Build | Quick Back In-Service | Abrasion & Chemical Resistant |...
From: $324.00- High Build - Impact & Chemical Resistant
- Quick back in-service light foot traffic 8-14 hrs
- Full chemical resistance only 3 days
- Excellent Adhesion 450 psi
- Abrasion resistant Only 23 mg loss (Tabor test)
- Excellent Chemical Resistance
- High build apply 10 to 20 mils one coat (80 - 160 sq'/gal)
- Wide Variety of 19 Different Colors
E5013 Fast Set Clear Epoxy Primer WB Concrete | Wood | Masonry
From: $60.00- Versatile product good on concrete, masonry, wood surfaces
- Quick 4-6 hour Recoat for same day projects
- Excellent as clear primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Long 2 hour pot life
- Excellent adhesion 425 psi
- Good chemical and abrasion resistance
- Water base
E5015 Epoxy Primer WB Coating | Concrete Wood Masonry | 20 Colors
From: $51.00- Versatile product good on concrete, masonry, wood surfaces
- Excellent as primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Available in Clear and 20 Colors To Match With Topcoat
- Long 1 - 1.5 hour pot life
- Excellent adhesion 425 psi
- Good chemical and abrasion resistance
- Water base
E505V Vertical Wall Epoxy Concrete Block Filler to 20 Mils No Sag | 11 Colors
From: $117.00- No sagging on vertical concrete and cement block walls up to 20 mils per coat
- Great epoxy block filler
- Good chemical and abrasion resistance
- Long 45 - 90 min pot life
- Excellent adhesion 420 psi @elcometer
- Wide selection of 11 color options
- 100% solids, very low voc
E517M Flake Filled Epoxy Mastic Steel & Concrete Coating | Chemical Containment | Low Temp 25F
From: $120.00- Self Priming on steel
- Excellent primary containment coating for internal tank linings (when part of specified system)
- Excellent secondary containment coating
- Performs well over epoxy mortars and properly primed concrete surfaces
- Can be applied on damp surfaces
- Excellent chemical resistance to acids, caustics, solvents
- Outstanding impact and abrasion resistance.
- Exceptional adhesion Exceeds 700 psi
- Excellent flexibility pass 7/8" mandrel 180º Bend
- Apply Vertical Surfaces to 15 mils one coat
- Meets USDA requirements.
- Low temp cure version to 25°F
- Low VOC 72 grams/Liter
E555VN Novolac Epoxy | Superior Steel & Concrete Chemical Vertical Protection | Tank Linings
$162.00- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
- Vertical application to 10 mils DFT.
- Great for Secondary Containment for both steel and concrete surfaces
- Use as Primary Containment and Tank Linings when used as part of specified system
- Excellent abrasion resistance with ceramic filler
- Excellent in battery storage room areas.
- Meets USDA requirements
- May be applied in cold, damp conditions to 45°F with curing down to 35°F
E572500 Non-Slip Skidproofer High Performance Epoxy Coating
From: $131.00- Great protection for problem slippery or wet concrete areas
- Outstanding slip resistance with a very aggressive textured anti-slip profile
- Excellent chemical and abrasion resistance
- Designed for high traffic and industrial areas
- Good For Docks, Ramps, Walkways etc
- 100% solids, 2 component
E5820 Oil Stop Epoxy Concrete Primer / Coating For Oil Contamination Areas
From: $50.00- Great for coating over oil contaminated concrete
- Can use as a primer before applying decorative coating systems
- Good as stand alone black colored coating
- Excellent substrate penetration through oil contaminated surfaces
- Excellent adhesion where standard epoxies typically fail
- Long 1 - 2 hour pot life
- High solids, 2 component
E5829 Flexible Epoxy Urethane Interior Expansion and Control Joint Sealant
From: $160.00- Flexible interior joint filler - Elongation 50.4% at 70F (ASTM D-412)
- Good for both expansion and control joints
- Great for general industry applications
- Hybrid epoxy urethane 2 component formula
- 100% solids with 0 voc
- Long 30-40 minute working time
- Low odor
- Paintable surface
E5829V Vertical Interior Wall Expansion & Flexible Joint Sealant
From: $162.00- Flexible vertical interior joint filler - Elongation 67% at 70F (ASTM D-412)
- No sag formula for vertical interior wall and overhead applications
- Hybrid urethane epoxy 2 component formula
- 100% solids with 0 voc
- Low odor
- Paintable surface
E5830 Flexible Interior Expansion & Control Joint Sealant | Fast Set | Cartridge Applied
From: $55.00- Flexible interior joint filler and sealant- Elongation 100%
- Easy Dual Cartridge Applied System
- Quick setting with light foot traffic in as little as 1 hour
- Excellent abrasion resistance
- 100% solids with 0 voc
- Low odor
- Paintable surface
E591 Wet Surface Epoxy | Cures to 35°F For Concrete and Steel | Floors – Walls
From: $130.00- May be applied on wet or under water surfaces
- Cold temperature application down to 35°F
- Self-priming on steel and on most concrete applications
- Long 40-50 POT Life at 75F
- Ideal for marginally prepared and painted surfaces
- Outstanding impact and abrasion
- High film build - Up to 20 mil DFT per coat on horizontal surfaces
- Vertical surfaces to 12 mils
- Excellent coating for manholes
- 100% solids and 0 g/L VOC's
- 3 Colors Available
E650 Non-Skid Epoxy Floor & Deck Low Temp 25°F | OSHA ADA Navy Spec Mil-PRF-24667B
From: $120.00- Heavy duty non-skid resistance for concrete & steel
- Available in fast cure, cold temp formula to 25°F
- Designed for wet areas
- Meets ADA and OSHA requirements for safe co-efficient of friction (COF) when properly applied
- Meets Navy Military Specification Mil-PRF-24667B for Non-Skid Deck Coatings
- Excellent adhesion, abrasion and impact resistance
- Resistant to grease, oil, salt water, alcohol, detergent, gasoline, hydraulic fluid
- Excellent coating for Diamond Plate
- Easy to apply, ready to use non-skid coating
- Comes in 4 colors
E671CL Epoxy Floor Coating | Clear | 100% Solids | For Metallic Pigment and Full Flake & Quartz...
From: $52.00- Clear epoxy great for use with metallic pigments and full flake or quartz broadcast systems
- High Build - 100% Solids Commercial Epoxy
- Good Adhesion 350 psi
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
E700HV Epoxy | Exceptionally Tough | Abrasion & Chemical Resistant | No Topcoat Required
From: $64.00- Saves Money - Eliminates Need for Urethane or Polyaspartic Topcoat
- Extremely Tough D-90 Shore Hardness
- Exceptional Abrasion resistance Only 19 mg loss (Tabor test)
- Excellent Adhesion 420 psi
- Good Chemical Resistance
- Great Looking Very High gloss (80-105 at 60 degrees @ glossmeter)
- 97% Solids Commercial Epoxy
- High build 15-30 mils one coat (53 - 106 sq'/gal)
- Wide Variety of 20 Colors
E707HB High Build 100% Solids Epoxy Floor Coating | 20 Colors
From: $55.00- High Build - 100% Solids Commercial Epoxy
- Long POT Life (working time) 30-50 min
- Excellent Adhesion 450 psi
- Abrasion resistant Only 32 mg loss (Tabor test)
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
- Wide Variety 20 Different Colors
E707LVP High Solids Epoxy Primer & Base Coat | Helps Prevent Outgassing | 20 Colors
From: $54.00- High Solids Commercial Grade Epoxy Primer
- Helps reduce problems from concrete outgassing (air bubbles)
- Long POT Life (working time) 35-55 min
- Excellent Adhesion 430 psi
- Good Chemical Resistance
- Wide Variety 20 Different Colors
GroundWorx SF ESD Static Dissipative Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014
From: $900.00- Static Dissipative 2 Part Water Based Thin Film Epoxy Floor Coating
- Static Dissipative 10e6 to 10e9 ohms
- Warrantied ANSI S20.20 performance
- Meets ANSI/ESD S20.20-2014
- Easy to Install
- For Concrete, Wood, VCT Tile Floors
- Use in Electronics Mfg, Assembly, ESD Protected Areas
- 6 Colors. Pewter Gray available for immediate shipment
H20 HyperPRIME Epoxy Quick Cure Bonding Primer | Low Temp 45°F | 1 Hr Recoat
$330.00- Excellent Substrate Penetration with superior adhesion 450 psi
- Great for concrete, wood and metal surfaces
- Helps protect Against Coating Damage from Outgassing of Concrete
- Quick Cure With 1 Hour Recoat Time - great for 1 day floor coating systems
- Available in Clear plus 6 Colors
- Water Base, No Offensive odors
- Cold temperature application down to 45F
- Good chemical and Stain Resistance
- Easy Application
- Available in Clear and 4 colors
HyperBOND Low Temp 40°F Epoxy Concrete Floor Coating | 100% Solids
From: $65.00- Tough, Durable Epoxy Coating
- Outstanding Bonding
- Cold temperature application down to 40°F
- Water Insensitive and Can Be Applied In Wet Conditions
- Resistant to Blushing/Sweating
- Good chemical, impact and abrasion resistance
- High solids 100%
- Available in clear & 14 colors! (Pigment sold separately)
HyperFLEX Epoxy | Flexible Membrane Concrete Wood | Low Temp 40°F | 100% Solids
From: $70.00- Tough, Durable Epoxy Coating
- Great for Quick Crack Repair and Control Joint Filler (when mixed with Fumed Silica)
- Can be used as a (1) basecoat for full broadcast floors, (2) flexible membrane, (3) repair gel to fill joints, cracks, & divots
- Cold temperature application down to 40°F
- Concrete & Wood Floors and Countertops
- Superior Flexibility and Outstanding Bonding
- Rapid Cure Rate For Same Day Full Flake System
- When used as membrane or basecoat HyperFLEX cures about 2 hours
- When used for gel repair cures about 10-15 minutes
- Good chemical and abrasion resistance
- High solids 100%
- Available in clear & 14 colors! (Pigment sold separately)
HyperREZ UV Low Temp 40°F High Build Epoxy Concrete Floor Coating | 100% Solids
From: $70.00- Tough, durable epoxy floor and countertop coating
- Cold temperature application down to 40F
- High Build Applications up to 32 mils/coat (50 sq'/gal)
- Long Working Time
- Good chemical and abrasion resistance
- UV Resistant
- High gloss appearance
- Designed for high traffic and industrial areas
- High solids 100%
- Available in clear & 14 colors (Colored Pigment Sold Separately)
Metallic Epoxy Color Pigment | Marbled 3-D Look | Pearlescent | Translucent 4oz (113g)
From: $19.99- Create a Beautiful Metallics Epoxy Floor System
- Vibrant and Exciting Pearlescent looking colors
- 3 Dimensional Marbled Appearance
- Unlimited Designs - Endless Possibilities
- 50 Different UV Resistant Colors
- See our 5 new Color Shifting, unique Multi-Colored pigments
- Add Metallics Pigment to HyerREZ UV Epoxy Or E671CL Epoxy as Part of 3 Step System
- Floor & Countertop projects on concrete and wood
- Pigment ships as Powder in Easy to Use 4 oz Container
MV2112 Moisture Vapor Barrier Primer Epoxy For Concrete Floors | ASTM F3010
From: $100.00- Reduce effects of moisture vapor transmission on concrete floors
- Control moisture vapor emission rates to 20 lb/24hr/1000 sq’ (ASTM F1869) or between 75% and 95% for ASTM F2170
- Superior moisture vapor control
- Class I Vapor Diffusion Retarder with perm rating of <.10
- Primer to protect Polymeric coating systems, vinyl sheets, tile, cementitious overlays, terrazo, wood veneers, and carpet
- 100% solids with 0 voc
- Meets ASTM F3010 for vapor permeance at the recommended thickness
NE253 Novolac Colored Epoxy Acid Solvent Chemical Resistant High Build
From: $386.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Resistant to high concentration acids, some chlorinated solvents incl xylene, MEK
- Resists wide range of chemicals, solvents and acids
- High build for heavy duty traffic projects, chemical troughs and curbs
- Great for tanks and chemical spill areas for cement, masonry or brick
- Excellent adhesion 425 psi
- Quick back in-service, light foot traffic 10-18 hrs
- Selection of 3 color options
- Low voc 47 g/L
NE253SL Novolac Epoxy Colored Slurry Acid Chemical Resistant Floor Coating
From: $230.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Apply to 1/16" thick to resurface traffic, chemical spill areas
- Resists wide range of chemicals, solvents and acids
- Resistant to high concentrations of acids and even some chlorinated solvents incl xylene, MEK
- Excellent adhesion 425 psi
- Quick back in-service with light foot traffic 10-18 hours
- Selection of 3 color options
- Low voc 22 g/L
NE253V Novolac Vertical Wall Colored Epoxy Chemical Resistant Acid Solvent
From: $57.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Resistant to high concentration acids, some chlorinated solvents incl xylene, MEK
- Apply up to 10 mils on vertical walls
- Resists wide range of chemicals, solvents and acids
- Medium build for chemical troughs and curbs
- Great for tanks and chemical spill areas for cement, masonry or brick
- Excellent adhesion 425 psi
- Quick recoat 5-10 hrs
- Selection of 3 color options
- Low voc <40 g/L
NE255P Novolac Epoxy Primer/Sealer Flexible Crack Bridging Chemical Resistant
From: $332.00- Excellent crack bridging, flexible high build primer eliminates need to repair hairline cracks in chemical exposure areas
- Use for priming light to medium duty secondary containment
- Tough, durable coating for surfaces exposed to vehicle traffic
- Outstanding abrasion and impact resistance with only 5 mg loss Taber Abrasion test and 100 inch lbs Gardner Impact Test
- Excellent adhesion 450 psi
- 100% solids, zero voc 0 g/L
NE256 Novolac Clear Epoxy Acid Solvent Chemical Resistant Floor Coating
From: $140.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Exceptional resistance to wide range of chemicals, solvents and acids
- Medium to High build for chemical spill areas, troughs, curbs and tanks
- Use as clear color coating or base for chip/flake or aggregate systems
- Excellent adhesion 400 psi
- Low voc <31 g/L
NE256M Novolac Epoxy Mortar Acid Solvent Chemical Resistant Patch Kit/Resurfacer
From: $83.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Apply at 1/8" to 1/4" to resurface traffic and chemical spill areas
- Used in many chemical immersion projects, curbs, tanks and chemical troughs
- Resists wide range of chemicals, solvents and acids
- Excellent impact and abrasion resistance
- Selection of 4 color options
- Low voc <14 g/L
NE258P Novolac Epoxy Clear Primer Acid Solvent Chemical Resistant Floor Coating
From: $346.00- Excellent primer companion to our NE256 Novolac Clear Epoxy topcoat
- Helps reduce air release generation when applying higher solids novolac topcoats
- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Resists wide range of chemicals, solvents and acids
- Excellent adhesion 365 psi
- Long working time with 1 to 3 hour POT life
NE259G Novolac Epoxy Grout Coat Acid Solvent Chemical Resistant Floor Coating
From: $183.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Resists wide range of chemicals, solvents and acids
- Low build epoxy to seal surface of existing mortar overlay system
- Great for topcoating/sealing poxy mortar power trowled or hand trowled systems
- Excellent adhesion 425 psi
- Selection of 3 color options
- Low voc <47 g/L
NE5928 Interior Expansion & Flexible Joint Novolac Chemical Sealant
From: $146.00- Flexible joint filler - Elongation 43.4% at 70F (ASTM D-412)
- Outstanding chemical and impact resistance
- Novolac epoxy urethane hybrid formula
- Excellent adhesion 420 psi
- 100% solids with 0 voc
- Low odor
- Paintable surface
NE5928V Vertical Interior Expansion & Flexible Joint Novolac Chemical Sealant
From: $145.00- Flexible vertical joint filler - Elongation 43.4% at 70F (ASTM D-412)
- No sag formula for vertical interior wall and overhead applications
- Outstanding chemical resistance
- Novolac epoxy and urethane hybrid formula
- Excellent impact resistance
- Good adhesion 380 psi
- 100% solids with 0 voc
- Low odor
- Paintable surface
NP-1 Cove Master Vertical Epoxy Mortar | 100% Solids | High Build | 4 Colors
From: $56.00- Easy construction of vertical cove bases
- 100% Solids Commercial Grade Epoxy
- High build formula
- 5 color options
- Comes as 3 part kit with aggregate or Liquid Only to add your own aggregate or NP1 can also be used as a primer.
UW601 Underwater Concrete Crack Filler Epoxy Paste Repair
$350.00- Make Repairs Underwater or on Wet Surfaces
- Concrete and Masonry
- Both Horizontal & Vertical Repairs
- Good for Cracks up to 1/8" and Thin Build Repairs
- Apply 35F - 90F
- 100% solids with 0 voc
- Low odor
UW602 Underwater Pourable Concrete Crack Filler Epoxy Repair
$325.00- Make Repairs Underwater or on Wet Surfaces
- Concrete, Cement and Masonry
- Both Horizontal & Vertical Repairs
- Good for Larger Cracks and Wide Variety of Repairs
- Easy to Use Pourable Formula
- 100% solids with 0 voc
- Low odor
FREE SHIPPING
All US Ground orders in Lower 48 States by FedEx and USPS
WORLDWIDE DELIVERY
Shipping Ground, Air, Ocean. Call about our Special Export Programs
Copyright 2021 by Exterior Performance Coatings