6700 Premium ESD Static Dissipative Anti-Static Floor Paint | 9 Colors | ANSI/ESD S20.20-2014

CURE SCHEDULE

(at 77F or 25C and 50% RH)

APPLICATION TEMPERATURE: 50-90 degrees F with relative humidity below 75%

MIXING AND APPLICATION INSTRUCTIONS

RODUCT STORAGE: Store product in an area so as to bring the material room temperature before using.  Continuous storage should be between 60 and 90 degree F.  Low temperatures or great temperature fluctuations may cause product crystallization.

GENERAL SURFACE PREPARATION:  All surfaces must be sound, dry, clean and free of oil, grease, dirt, mildew, form release agents, curing compounds, loose and flaking paint and other foreign substances.

How to Ground 6700:  We offer a Two-inch-wide copper grounding strip for grounding to earth grounds. Copper is 1.4 mil thickness (2.6 mil thickness with the conductive adhesive backing).  Recommend at least 1 grounding strip every 1,000 sq’ of project surface area.  See the guide:  HOW TO GROUND ESD COATINGS

SCHEMATIC FOR GROUNDING AN ESD FLOOR COATING

NEW SURFACES: Concrete (concrete floors) and masonry Do not use on floors subject to hydrostatic pressure. Cure at least 30 days before painting. pH must be 10.0 or lower. Roughen slick poured or precast concrete and remove sealers by chemical cleaning or abrasive method such as sandsweeping. Rinse thoroughly with water and allow to dry. Must be internally dry. Remove loose aggregate. Prime with this product. Wood: sand smooth. Remove sanding dust. Prime with this product. Steel: Performance over hand or power tool cleaned surfaces is dependent on the degree of cleaning. Prime with a metal primer. Galvanized metal and aluminum: Clean off oils and other contaminates. Prime with a galvanized metal primer.

PREVIOUSLY PAINTED SURFACES Wash to remove contaminants. Rinse thoroughly with water and allow to dry. Dull glossy areas by light sanding. Remove sanding dust. Remove loose paint. Scrub heavy chalk areas and overhead (exterior) areas such as eaves with soap and water. Remove all mildew by washing with a solution of 16 oz (473 mL) liquid household bleach and two oz (59 mL) non-ammoniated liquid detergent per gallon (3.785 L) of water. Rinse thoroughly with water and allow to dry. Prime bare areas with primer specified under NEW SURFACES. WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC.  EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear an NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before starting project, find out how to protect yourself and others by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

SPREADING RATE:Apply at approx. 200 sq ft/gal. Actual coverage may vary depending on substrate and application method.

DRYING TIME:  At 770 F (250 C) and 50% RH, dries to touch in 2 to 4 hours, to recoat in 8 hours and to light foot traffic in 24 hours. Low temperature, high humidity, thick films or poor ventilation will increase these times.

PRODUCT APPLICATION:Mix thoroughly before use. May be applied by brush, roller or spray. No thinning required. For airless spray application, use a .015” – .019” tip at 2000 psi, adjust pressure as needed.  Do not apply when surface or air temperature is below 50F ( 10C) or if rain or heavy dew is expected within 48 hours of application. Two coats are suggested for best results. Spot treatments can be applied for worn areas over previously applied ACL Staticide Dissipative Floor Finish without any hot spots. For interior use, allow adequate ventilation during application and drying.

CLEANUP: Clean hands and tools immediately with warm, soapy water.  Clean spills right away with a damp cloth.

FLOOR CLEANING: Caution!  Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing your cleaning technique.  If no ill effects are noted, you can continue to clean with the product and process tested.

RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure).  It is best to let the floor remain dry for the full cure cycle. Dependent on actual complete system application, surface may be slippery, especially when wet or contaminated; keep surface clean and dry.

LIMITATIONS:

• Substrate temperature must be 5°F above dew point.
• All new concrete must be cured for at least 30 days prior to application.
• Physical properties are typical values and not specifications.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products

What is 6700 dissipative anti-static floor paint?

6700 is a water-based acrylic vinyl static dissipative coating designed for use in ESD-controlled environments. It provides consistent electrostatic control with a resistance range of 10⁷ to 10⁹ ohms, helping prevent static buildup on floors and surfaces.

What makes this a “static dissipative” coating?

A dissipative coating safely controls static electricity by allowing it to gradually discharge rather than build up or discharge suddenly. The 6700 coating falls within the 10⁷–10⁹ ohms range, making it ideal for controlled environments where sensitive electronics are present.

Does 6700 meet ESD standards?

Yes. 6700 conforms to ANSI/ESD S20.20-2014 when tested according to ANSI/ESD STM7.1, making it suitable for professional ESD compliance programs.

Where is 6700 ESD floor paint typically used?

This dissipative floor coating is recommended for:

• Electronics manufacturing and assembly areas
• ESD-protected environments
• Static-sensitive workspaces

It is specifically designed for environments where electrostatic discharge must be controlled.

What surfaces can 6700 anti-static coating be applied to?

6700 can be applied to multiple substrates including:

• Concrete floors
• Wood surfaces
• Metal surfaces
• Walls and other interior or exterior areas

Proper surface preparation is required for best performance.

Can this coating be used indoors and outdoors?

Yes. 6700 is suitable for both interior and exterior applications, offering flexibility across a wide range of projects.

How durable is 6700 dissipative floor paint?

This anti-static coating offers:

• Good resistance to abrasion
• Resistance to oils and washing
• Excellent adhesion and color retention

These features make it a reliable option for light to moderate traffic environments.

Does 6700 require a primer or topcoat?

• Primer: Recommended depending on substrate (especially for surfaces like tile, vinyl, or adhesives)
• Topcoat: Not required, but an optional acrylic clear finish can be used for added protection

This flexibility makes it easy to integrate into different floor systems.

How is grounding achieved with this ESD coating?

Grounding can be achieved using a copper grounding strip, typically installed at a rate of one strip per 1,000 sq ft, allowing the dissipative coating to safely channel static to ground.

What is the coverage rate for 6700 floor paint?

Coverage is approximately 200 square feet per gallon, depending on surface conditions and application method.

How long does it take to dry and cure?

At standard conditions (77°F, 50% RH):

• Dry to touch: 2–4 hours
• Recoat: 8 hours
• Light foot traffic: 24 hours
• Full cure: 3–5 days

Proper curing ensures optimal anti-static performance.

Is 6700 environmentally friendly?

Yes. This coating is:

• Low VOC (50 g/L)
• Non-hazardous
• Non-flammable

It is designed for safer application in industrial and commercial environments.

What finish and color options are available?

6700 features a low gloss satin finish and is available in:

• 9 standard colors (including gray, black, blue, green, beige, and safety yellow)
• Custom colors available upon request

This allows both functional and aesthetic flexibility.

Does this coating create “hot spots”?

No. The 6700 system is designed to provide uniform static dissipation with no hot spots, ensuring consistent ESD protection across the entire surface.

Can 6700 be used in heavy traffic environments?

For heavy-duty use such as forklift or pallet jack traffic, a more robust system (such as a multi-component epoxy/urethane system) is recommended instead of a single-component coating like 6700.

What preparation is required before applying 6700?

All surfaces must be:

• Clean and dry
• Free of oil, grease, and contaminants
• Properly cured (for concrete, at least 30 days)

Surface preparation is critical to ensure adhesion and long-term performance.

What temperature conditions are required for application?

Apply between 50°F and 90°F with relative humidity below 75% for best results