Prime, Prep & Repair
Filter By Category
Questions about our products?
Call us for help picking the correct solution for your project. (630) 675-4509
Showing 1–50 of 114 results
-
Chalky Wall Sealer and Clear Acrylic Primer
- Flexible and breathable
- Helps prevent efflorescence
- Protects wood from swelling, shrinking, or grain raising
- Seals and binds chalked surfaces; improves adhesion of topcoat
- May be used on previously painted and properly prepared surfaces
-
4100 ESD Restorer | Cleaner Concentrate
- Lengthens maintenance cycle
- Removes black heel marks
- Revitalizes gloss
- Surface resistivity: 107–109 ohms per square @100 volts
- High solids concentrate
-
4020 ESD Neutralizer Cleaner Concentrate
- Economical concentrate
- Dilute 1:128 cleaner to water
- Neutral pH 7.2
- Low foam - no streaking formula
- Non-toxic and biodegradable safe for sewage & septic systems
-
4010 Acrylic ESD Floor Stripper Concentrate
- Prepares floor for application of acrylic based ESD floor finishes
- No ammonia or phosphates
- Effective in hard or soft water
- Low 6% V.O.C.
- Zero tribogeneration
-
4030 ESD Neutralizer Cleaner Ready-to-Use
- Ready-to-use (also available as a concentrate, see 4020)
- Neutral pH 7.2
- Low foam - no streaking formula
- Non-toxic and biodegradable safe for sewage & septic systems
- Non-abrasive
-
ScrubWorx 20.20 ESD Floor Cleaner Concentrate
- Static Conductive
- High Activity Cleaner
- Micro-Cleans & Conditions
- Chemically Seals Tiles
- Simple to Use
-
800 Slow Set Polyurea Adhesive Sealant & Caulk
- Back in-service 1 - 1.5 hours, recoat 30-45 minutes, full cure 6-8 hours
- High chemical & fuel resistance
- Highly adhesive to many substrates
- Good working time, quick gel time 6-10 minutes, trowel-able
- Cartridge or pump dispensed
-
830 Fast Set Polyurea Repair | Joint Sealant | Caulk | Adhesive | No Sag Walls | Concrete | Steel | Wood
- Vertical hold directly from the cartridge or static mixer
- Can be sprayed over with polyurea in a short time
- High chemical resistance, fuel resistant,
- Highly adhesive to many substrates
- Cold weather application down to -20F
-
ProGrout (formerly 4034) Polyurea Concrete Quick Repair | Ultra Low Viscosity | Apply Low Temp -20°F | Low Odor
- Back-in-service as fast as 30 min with heavy forklift loads
- Meets OSHA fork lift operator floor facility safety, surface conditions
- Save Bearings & Wheels On Electric Pallet Jacks and Electric Lifts.
- Meets USDA requirements
- Cold applications down to -20°F (-26°C)
-
3246 Polyurea Flexible Expansion Joint Filler | Quick Cure | Exterior Interior | Low Temp -20°F | Elongation 600%+
- Quick set with "Drive-Over" in 30 to 45 minutes
- High Density Polyurea
- Very Flexible with Elongation ASTM D124 >600%
- Meets USDA Requirements for intermittent contact
- Meets FAA P605 – for airfield joints
-
CMW 8000 Lithium Moisture Vapor Barrier and Concrete Densifier
- Blocks moisture vapor and hydrostatic pressure reducer
- Used in joints to stop vapor/water pressure damage to joint materials
- Permanent - becomes part of the concrete
- Stops minute fracture weeping of moisture (may require several coats)
- In areas of high humidity and salt air - reduces corrosive activity to rebar within concrete
-
7001 Polyurethane Primer Concrete & Steel | Quick Cure | Exceptional Adhesion | Low 35F Temp
- Concrete & Steel Primer For Epoxy, Urethane, Polyaspartic, Polyurea Coatings
- Cross-links With Polyurea, EPDM Roofing and other Plastic Materials Difficult to Bond to
- Deep Penetrating Exceptional 1200 psi Adhesion
- Superior Corrosion, Abrasion and Water Resistance
- For Use in Submerged Service Applications
-
6007 Wet Condition Epoxy For Concrete & Steel | Low Temp 35°F | 100% Solids
- May be applied in damp and wet conditions where wash-down of areas is problematic
- Withstands up to 15-18 psi hydraulic vapor pressure
- Provides protective attractive color coat epoxy flooring system
- Excellent working properties
- Exceptional corrosion protection of both concrete and steel
-
3003 Polyurea Slow Set Interior Control Joint Filler | Low Temp -20°F
- Offers load transfer across control joints for good protection of edges
- Back-in-Service "Drive-Over" in 30 to 60 minutes
- Longer working time than the 3004 Fast Set Polyurea
- 5-8 Minute Gel Time @ 77°F
- Meets USDA Requirements for incidental food contact
-
3004 Polyurea Fast Set Interior Control Joint Filler | Low Temp -20°F
- Quick Back-in-Service "Drive-Over" in only 20-30 minutes
- Offers load transfer across control joints for good protection of edges
- Ideal for High Speed Application using Machine Dispensing System or for small projects easy application using twin cartridge kits and 300 ml x 300 ml cartridge kits (total 21 oz or 600 ml per cartridge kit)
- Tack Free only 2-3 minutes
- Meets USDA Requirements for incidental food contact
-
E1015V Vertical Wall Epoxy Coating & Primer to 8 Mils No Sag | 11 Colo
- No sagging on vertical walls up to 8 mils per coat (4 mils DFT)
- Good for priming or coating concrete, wood or masonry.
- Good chemical and abrasion resistance
- Long 1 - 1.5 hour pot life
- Excellent adhesion 425 psi @elcometer
-
E5015 Epoxy Primer WB Coating | Concrete Wood Masonry | 20 Colors
- Versatile product good on concrete, masonry, wood surfaces
- Available in Clear and 20 Colors To Match With Topcoat
- Excellent as primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Long 1 - 1.5 hour pot life
-
E1409CL Moisture Vapor Barrier Epoxy Sealer Primer For Concrete ASTM F3010
- Helps reduce effects of moisture vapor transmission
- Control moisture vapor emission rates up to 20 lb/24hr/1000 sq' (ASTM F1869)
- 100% solids with 0 voc
- Low odor
- Easy to apply, most projects require only one coat
-
E57936 Lithium Concrete Densifier | Deep Penetrating
- Increases durability by improving resistance to freeze thaw effects
- Improves abrasion resistance and durability.
- Improves weathering, densifies and reduces efflorescence of natural stone, precast stone and cement.
- Protects and fortifies concrete as it seals against moisture damage.
- Application will reduce dusting and increase concrete life
-
E57937 Lithium Concrete Densifier Extra Strength | Deep Penetrating
- Increases durability by improving resistance to freeze thaw effects
- Improves abrasion resistance and durability.
- Improves weathering, densifies and reduces efflorescence of natural stone, precast stone and cement.
- Protects and fortifies concrete as it seals against moisture damage.
- Application will reduce concrete dusting and increase concrete life
-
E57940 Concrete Conditioner With Stain Guard
- Increases durability and stain resistance, gloss level and abrasion resistance.
- Improves weathering, densifies and reduces efflorescence.
- Protects and fortifies concrete as it seals against moisture damage.
- Application will reduce dusting and increase concrete life.
- Reduces water absorption into the substrate.
-
E5829V Vertical Interior Wall Expansion & Flexible Joint Sealant
- Flexible vertical interior joint filler - Elongation 67% at 70F (ASTM D-412)
- No sag formula for interior vertical wall and overhead applications
- Hybrid epoxy urethane 2 component formula
- 100% solids with 0 voc
- Low odor
-
E5829 Flexible Epoxy Urethane Interior Expansion and Control Joint Sealant
- Flexible interior joint filler and sealant- Elongation 50.4% at 70F (ASTM D-412)
- Hybrid epoxy urethane 2 component formula
- 100% solids with 0 voc
- Low odor
- Paintable surface
-
E5820 Oil Stop Epoxy Concrete Primer / Coating For Oil Contamination Areas
- Great for coating over oil contaminated concrete
- Can use as a primer before applying decorative coating systems
- Good as stand alone black colored coating with a satin sheen
- Excellent substrate penetration through oil contaminated surfaces
- Excellent adhesion where standard epoxies typically fail
-
E-Poly Pigment For All Floorguard Epoxy & Polyaspartic Coatings | 12 Colors
Starting at $52.00 -
MV2112 Moisture Vapor Barrier Primer Epoxy For Concrete Floors | ASTM F3010
- Reduce effects of moisture vapor transmission on concrete floors
- Control moisture vapor emission rates to 20 lb/24hr/1000 sq’ (ASTM F1869) or between 75% and 95% for ASTM F2170
- Class I Vapor Diffusion Retarder with Superior moisture vapor control, perm rating of <.10
- Primer to protect Polymeric coating systems, vinyl sheets, tile, cementitious overlays, terrazo, wood veneers, and carpet
- 100% solids with 0 voc
-
UW601 Underwater Concrete Crack Filler Epoxy Paste Repair
- Make Repairs Underwater or on Wet Surfaces
- Concrete and Masonry
- Both Horizontal & Vertical Repairs
- Good for Cracks up to 1/8" and Thin Build Repairs
- 100% solids with 0 voc
-
UW602 Underwater Pourable Concrete Crack Filler Epoxy Repair
- Make Repairs Underwater or on Wet Surfaces
- Concrete, Cement and Masonry
- Both Horizontal & Vertical Repairs
- Good for Cracks and Wide Variety of Repairs
- Easy to Use Pourable Formula
-
E130A Oil Contaminated Concrete & Asphalt Epoxy Mortar Patch Kit/Resurfacer
- Great for patching and repairing oil contaminated and damaged concrete
- Can be used to patch and repair asphalt surfaces
- Crack. holes and general surface repairs
- Apply up to 1/4" per coat
- Excellent abrasion and impact resistance
-
NE257P Novolac Epoxy Colored Primer Acid Solvent Chemical Resistant Fl
- Excellent primer companion to our NE253 and NE253SL Novolac Epoxy topcoats
- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Resists wide range of chemicals, solvents and acids
- Excellent adhesion 375 psi
- Long working time with 1 to 3 hour POT life
-
NE255P Novolac Epoxy Primer/Sealer Flexible Crack Bridging Chemical Resistant
- Excellent crack bridging, flexible high build primer eliminates need to repair hairline cracks in chemical exposure areas
- Use for priming light to medium duty secondary containment
- Tough, durable coating for surfaces exposed to vehicle traffic
- Outstanding abrasion and impact resistance with only 5 mg loss Taber Abrasion test and 100 inch lbs Gardner Impact Test
- Excellent adhesion 450 psi
-
NE256M Novolac Epoxy Mortar Acid Solvent Chemical Resistant Patch Kit/Resurfacer
- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Apply at 1/8" to 1/4" to resurface traffic and chemical spill areas
- Used in many chemical immersion projects, curbs, tanks and chemical troughs
- Resists wide range of chemicals, solvents and acids
- Excellent impact and abrasion resistance
-
NE258P Novolac Epoxy Clear Primer Acid Solvent Chemical Resistant Floor Coating
- Excellent primer companion to our NE256 Novolac Clear Epoxy topcoat
- Helps reduce air release generation when applying higher solids novolac topcoats
- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Resists wide range of chemicals, solvents and acids
- Excellent adhesion 365 psi
-
Pigment to Color 5500 Polyaspartic | 17 colors
Starting at $59.00 -
E343 Quick Fix Concrete Repair Epoxy Urethane Patch Kit | 10 Min Light Traffic | Low Temp 20°F
- Extremely Quick full cure 1 hour
- Tough Durable Repair as hard as concrete
- Good for use interior & exterior repairs
- Low viscosity Product for Outstanding Adhesion and Deep Penetration of Cracks
- Comes in both small and large patch kits including silica sand and liquid only options
-
E707LVP High Solids Epoxy Primer & Base Coat | Helps Prevent Outgassin
- High Solids Commercial Grade Epoxy Primer
- Helps reduce problems from concrete outgassing (air bubbles)
- Long POT Life (working time) 35-55 min
- Excellent Adhesion 430 psi
- Good Chemical Resistance
-
E100 Urethane Primer Finish Coat | Aluminum Galvanized & Rusty Steel | Dry Heat to 400 °F | Apply Down to18°F | Quick Cure
- Prime over Steel, metal, weathered galvanized steel, aluminum, fiberglass, polyurethane foam and previously painted surfaces
- Fast recoat 1-2 hours at 75°F & 50% R.H
- Cures down to 18°F dry and apply to 140°F
- High heat resistance up to 400°F dry
- Single component, easy to use
-
E1000 Epoxy Concrete Repair Kit | Holes to 1″ | Cracks | Spall | 3 Color
- Make quick, permanent repairs to concrete
- Patch cracks, spalled concrete and potholes
- Outstanding adhesion to concrete
- Excellent chemical, abrasion and impact resistance
- USDA approved for food processing plants
-
Universal Pigment Color for Polyaspartic, Epoxy & Urethane Coatings
Starting at $45.00 -
H20 HyperPRIME Epoxy Quick Cure Bonding Primer | Low Temp 45°F | 3 Hr Recoat
- Excellent Substrate Penetration with superior adhesion 450 psi
- Quick Cure 3 Hour Recoat Time - great for 1 day floor coating systems
- Great for concrete, wood and metal surfaces
- Helps protect Against Coating Damage from Outgassing of Concrete
- Fantastic freeze/thaw stability (passes 3+ cycles; -5 C to 23 C)
-
E105M Epoxy Mortar Concrete Resurfacer & Patch Kit
- Economical, Easy resurfacing old and damaged concrete floors
- Compressive Strength 8,400 psi ASTM D695
- Heat Deflection Temp 131.7F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
-
HDK H18 Fumed Silica Thickening Agent For Epoxy Concrete Crack and Joint Repair | (10kg) 22 lbs | Wacker
- Great thickening agent to wide range of coatings including epoxy and polyurethane coatings
- Allows coatings to be used as great concrete crack, hole, joint and spall repairs
- When mixed into fast cure epoxy, makes for very quick repairs
-
HyperCURE Concrete and Wood Repair Kit | Flexible 100% Elongation | Quick Cure | Easy To Apply | Recoat 15 – 30 min
- Superior Flexibility 100% Elongation
- Outstanding Bonding
- Fast Cure - 15 to 30 min recoat
- Rapid Cure Rate For Same Day System Application
- High D70 Hardness
-
E128AF Arctic Epoxy Mortar Concrete Patch Kit | Cold Condition -10°F to 40°F
- Tough, durable cold winter weather Concrete Patch and Repair
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- Excellent extreme cold condition patching -10°F to 40°F
- Great For Freezer, Cold Storage and Cold Winter Patching
-
E110M Epoxy Mortar Concrete Premium Resurfacer & Patch Kit
- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- 10% greater coverage/unit vs E105M Epoxy Mortar
- Compressive Strength 11,150 psi ASTM D695
- Heat Deflection Temp 158.9F ASTM D648
-
E126CW Cold Weather Epoxy Mortar Concrete Resurfacer & Patch Kit 35°F to 80°F
- Great for Cold Weather & Cold Freezer Storage
- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- Compressive Strength 11,284 psi ASTM D695
- Heat Deflection Temp 149.9F ASTM D648
-
E916MF Multi-Functional Heavy Duty Cleaner Concentrate | Floors Walls Equipment
- Rapidly removes dirt, grease and grime from wide variety surfaces
- Dissolves and removes food grease and many industrial oils and greases
- Use as general-purpose cleaner, floor cleaner, wax and floor finish stripper, engine degreaser and many other cleaning problems.
- Use by hand or through steam or pressure cleaning equipment, automatic floor scrubbers, etc
- Economical Concentrate Formula. Dilution rates to 1:30 for sensitive surfaces.
-
E915HD Heavy Duty Cleaner Degreaser Concentrate | 100% Biodegradable
- Heavy duty cleaner formulated for versatility and dependability.
- Rapidly removes dirt, grease and grime from wide variety surfaces
- Compatible with most industrial floor coatings incl Epoxies, Polyaspartics, Urethanes
- Dissolves and removes food grease and many industrial oils and greases
- Use as general-purpose cleaner, floor cleaner, wax and floor finish stripper, engine degreaser and many other cleaning problems.
-
E15M Epoxy Mastic Steel Primer DTM & Concrete Coating | Chemical Resistant | Low Temp 25F
- High solids DTM (direct-to-metal) chemical resistant steel primer or finish coat to steel and concrete
- Self priming to steel including tight rust
- Apply Vertical Surfaces to 8 mils DFT Steel & Concrete
- Great primer for use with our E1500HN (horizontal) and E555VN (vertical) Novolac Chemical Resistant Epoxies
- USDA Approved
-
E5013 Fast Set Clear Epoxy Primer WB Concrete | Wood | Masonry
- Versatile product good on concrete, masonry, wood surfaces
- Quick 4-6 hour Recoat for same day projects
- Excellent as clear primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Long 2 hour pot life