4400 ESD Polyurethane Anti-Static Floor & Wall Paint | ANSI/ESD S20.20 | Zero VOC | Reinforcing Fibers

APPLICATION TEMPERATURE: 60-80 degrees F with relative humidity below 80%

CURE SCHEDULE

APPLICATION TEMPERATURE: 60-80 degrees F with relative humidity below 80%

APPLICATION INSTRUCTIONS

Recommendations before beginning:

 Read this entire document before application.

 Always wear protective goggles and gloves.

 Apply a test patch of the 4400 Staticide ESD Polycoat paint for adhesion, abrasion, resistance and aesthetics prior to coating large areas.

 Average coverage: 200-250 sq. ft. per gallon

 For best results, apply at temperatures between 60°F-80°F.

 Mix products thoroughly before using as solids may settle in storage. Fibers are noticeable in wet mixture but will be absorbed into the coating as the coating dries. Stirring with a paint stick my not be adequate for mixing solids into solution. Mixing with a drill attachment is recommended.

 Two coats are not required, but may be preferred as substrate absorbency varies.

NEW CONCRETE FLOORS

New concrete should cure for a minimum of thirty days before coating with product.

1. Clean and remove dirt/grease with diluted 4040 Staticide Cleaner Concentrate solution. Dilute 5:1 (water to concentrate). Scrub with auto scrubber with stripping pad or a stiff bristle broom brush.

2. Rinse twice with water. Residual acid, stripper or detergent will detrimentally affect the paint adhesion.

3. Test with litmus paper to ensure all the acid is removed and the floor has a neutral pH. Allow to dry 24 hours.

4. Determine porosity of floor using Porosity Test found on page 3 of this manual. Very dense, non-porous or treated concrete may require additional acid treatment.

5. Thoroughly mix paint with mixer or stirrer. This will ensure that the conductive additives are properly dispersed, allowing for proper adhesion and conductivity.

6. Pour a quantity of paint into a roller tray and completely wet the roller. A foam roller or 1⁄4” nap polyester roller with a five-foot extension handle is recommended. Roller will depend on surface. Saturate roller completely and apply paint in continuous strokes to avoid fiber clumping.

7. Allow floor to dry overnight at not less than 60°F before allowing light foot traffic to resume on the surface.

8. After drying, test the floor with a surface resistivity meter. If the reading is greater than 108 ohms and/or the readings on five separate test spots on the floor differ by more than a decade, apply a second coat of paint.

9. Allow floor to dry 3 days (72 hours minimum) at not less than 60°F before allowing general industrial traffic to resume.

10. Allow floor to dry 3 days (72 hours minimum) at not less than 60°F if applying optional coat of ESD floor finish. ACL dissipative floor finishes will provide an increase in gloss and durability.

OLD CONCRETE FLOORS

*NOTE* Simple cleaning may be insufficient to obtain maximum adhesion of paint to old concrete floors. Prior maintenance and exposure to polyethylene wax, silicone, epoxy sealers, oil spills and other coatings or chemicals will adversely affect product performance.

1. Follow steps #1 – #4 listed above.

2. Apply a test patch. If the test patch is acceptable, follow the instructions under “NEW CONCRETE FLOORS” starting at step #5.

3. If the test patch shows unacceptable adhesion after standing five days, proceed with the following:

a. Grit sand or solvent clean the concrete to remove all embedded sealers, waxes, floor polishes, oils, greases, fluids, and chemical spills of any type.

* NOTE* Consult your concrete contractor for details on proper equipment for floor sanding.

b. After sanding, wash the floor with detergent and warm water then wet vacuum.

c. Allow the floor to dry completely.

d. Apply another test patch. If adhesion, abrasion, resistance and aesthetics are acceptable, follow the instructions under “NEW CONCRETE FLOORS” starting at step #5.

VCT OR VINYL FLOORS

Prep the surface with the 4040 Universal Cleaner, rinse with water, and apply once the substrate is dry.

REGULAR MAINTENANCE

1. Allow 2 weeks of drying time after initial paint application before using a damp mop to clean coated floor.

2. Sweep or dust mop daily. Use sweeper, vacuum, or an untreated mop to clean the floor.

Porosity Test: Pour one ounce of water onto the concrete. If the water soaks in, the surface is porous enough for coating. If water beads up on the concrete, the surface is not porous and further treatment is required. The presence of laitance (fine white particles) will also require abrasive blasting, sanding or abrading to assure removal.

Dryness Test: Place a weighted rubber mat, piece of plastic sheet or other non-porous material on the surface for 24 hours. If the underside of the mat, plastic or concrete surface is dry after that time, then the floor is ready for the next step. If moisture persists, concrete surface cannot be coated.

Do not use a sweeping compound.

3. Damp mop weekly.

4. Remove all spills immediately.

5. Do not machine buff floor. Do not use abrasive cleaners or scrubbing machines with abrasive pads to clean the painted floor.

4400 Staticide® Premium Polyurethane ESD Coating may be touched up any time with additional coats.

FINAL NOTE

It is crucial to begin a program of taking regular readings of surface resistance from appropriate test sites to evaluate the floor and establish a proper maintenance program tailored to your requirements. All surface resistivity readings should be taken when the floor is at room temperature and dry. In order to conform to ANSI/EOS specifications and standards, use a resistance meter and procedure that measures relative humidity, temperature, and surface resistance such as the ACL 800 or ACL 880.

Apply 1 copper grounding strip every 1,000 sq’ of project surface area.

How to Ground 4400:  We also offer the option to include a Two-inch-wide copper grounding strip for grounding to earth grounds. Copper is 1.4 mil thickness (2.6 mil thickness with the conductive adhesive backing).  Recommend at least 1 grounding strip every 1,000 sq' of project surface area.  See the guide:  HOW TO GROUND ESD COATINGS

Porosity Test: Pour one ounce of water onto the concrete. If the water soaks in, the surface is porous enough for coating. If water beads up on the concrete, the surface is not porous and further treatment is required. The presence of laitance (fine white particles) will also require abrasive blasting, sanding or abrading to assure removal.

Dryness Test: Place a weighted rubber mat, piece of plastic sheet or other non-porous material on the surface for 24 hours. If the underside of the mat, plastic or concrete surface is dry after that time, then the floor is ready for the next step. If moisture persists, concrete surface cannot be coated.

Check out our customer projects using the 4400 ESD Polyurethane Coating!

Electronics Factory ANSI 20.20 ESD Anti-Static Floor