Call us (630) 675-4509
Exterior Performance Coatings offers a wide range of professional-grade solid epoxy and urethane floor coatings for most commercial, residential, and industrial projects. Whether your floor gets light foot traffic or you’re looking to protect an industrial garage floor from heavy vehicular traffic, we’ve got you covered. Our industrial floor coatings are quick-setting and able to endure low temperatures.
Exterior Performance Coatings is the ideal place for contractors and DIY enthusiasts to purchase outdoor floor finishes. All of our industrial floor coating products are professional-grade so you can achieve professional results without breaking the bank. We also offer free shipping in the continental US.
Show
Filter by
Filter by
Filter by
1007 Polyurea Coating Fast Set Waterproof Spray | Elastomeric 100% Solids
$7,326.00- 100% Pure Polyurea Waterproof Spray Coating
- Fast 10-30 Sec Set Time - Quick Back In-Service
- Flexible Elastomeric Spray 600%+ Elongation
- Excellent Chemical, Abrasion Impact Resistance
- Unlimited mil/coat & unlimited recoat window
- Use on Concrete, Metal, Wood
- Good for Garages, Marine Enviroments, Secondary Containment, Industrial Applications
4700SS ESD Static Dissipative Acrylic Polyurethane Anti-Static Floor Paint | ANSI/ESD S20.20-2014
From: $311.00- Economical Acrylic Polyurethane Anti-Static Floor Coating
- Static dissipative: 105 to 108 ohms
- Conforms to ANSI/ESD S20.20-2014 when tested according to ANSI/ESD STM7.1
- For Concrete & Unfinished Hard Floor Surface
- Consistent Resistivity 100 kilohms to 100 meg ohms Regardless of Humidity
- Data Center, Warehouse, Electronics Mfg, Assembly
- Water Base, UV Resistant, Comes in Dark Grey
4800 Ultra II Static Dissipative Clear Urethane Floor Finish
From: $325.00- Abrasion Resistant Urethane Enhanced Finish
- For Concrete, Epoxy, ESD epoxy, Dissipative Tile
- Increase Strip Cycle to 24 Mos
- Meets ANSI S20.20-2007
- UL Listed Slip Resistant
- Great For Electronics, Medical, ESD Protected Areas
Hot
5500 Polyaspartic Polyurea Coating Roll Down Low Temp 30°F | 87% Solids
From: $149.00- Beautiful Decorative High Gloss Appearance
- Cold Temperature Application to 30F using Fast Set
- Easy Squeegee/Roller Application
- Waterproof, Aliphatic Resists UV Non-Yellowing
- Indoor & Outdoor Floor and Countertop Projects
- Good In Submerged Service Projects Like Fountains
- Works well on concrete, brick, steel, wood, fiberglass
- Excellent Chemical & Abrasion Resistance
- Highly Adhesive, Flexible & Non-Brittle
- Optional Fast or Slow Set, High Heat & Humidty
- Great For Garage Floors Using Chips & Flakes
- Commercial and Industrial Applications
- Use as Stand Alone System or Topcoat to Epoxy
6007 Wet Condition Epoxy For Concrete & Steel | Low Temp 35°F
From: $593.00- Protect Problem Wet and Damp Areas
- Withstands to 20 PSI Hydralic Vapor Pressure
- Cold temperature down to 35°F
- Designed to Protect both Concrete and Steel
- Use as Primer With Topcoat or Floor Coating
- Offers Excelllent Moisture and Corrosive Protection with Outstanding Adhesion
- 100% Solids, no VOC, 2 Component
Hot
6009 Epoxy Floor Coating Industrial & Commercial Low Temp 35°F | 100% Solids | Quick Cure
From: $115.00- Commercial, Industrial, Residential Concrete Floors
- Cold temperature down to 35°F
- Tough - Attractive Looking Epoxy
- Good Chemical, Abrasion, Impact Resistance
- Quick 4 to 7 hour set time
- Self Priming With No Primer Required
- 100% Solids, no VOC, 2 Component
- Clear or Selection of Colors
- Excellent Protection at Lower Cost
7001 Polyurethane Primer Concrete & Steel | Quick Cure | Exceptional Adhesion | Low 35F Temp
From: $80.00- Concrete & Steel Primer For Epoxy, Urethane, Polyaspartic, Polyurea Coatings
- Cross-links With Polyurea, EPDM Roofing and other Plastic Materials Difficult to Bond to
- Deep Penetrating Exceptional 1200 psi Adhesion
- Superior Corrosion, Abrasion and Water Resistance
- For Use in Submerged Service Applications
- Quick 1 hr recoat (based on temp & humidity)
- Semi-flexible & impact resistance
- Reduced concrete outgassing problems
- Moisture Cured easy to use 1 Component
- Wide application range 35°F - 125°F (1.7°C - 52°C)
Advanced Waterproofer Multi-Surface 10 Yr Water Repellent
From: $19.00- Designed For Homeowners Wanting Superior Protection Against Moisture and Stains
- 10 Year Premium Water Sealer
- Unpainted Porous Concrete, Block, Brick, Wood, Stone
- Clear Finish, Will Not Yellow
- Water Base, Low VOC, Eco-Friendly
- Easy To Apply
Aluminum Oxide High Wear Abrasion Resistant Additive | 220 Grit | 325 Grit for Urethane & Polya...
From: $31.00- Significantly improves abrasion resistance of floor coatings
- Helps create a tough, durable, abrasion resistant surface
- Simple and easy to add while mixing a coating
- Works with any urethane and thin film polyasprtic coating
- Works well with high performance 2 part floor coatings
- Does not change physical properties of the coating
- Well bonded into the body of the coating
- High hydrolitic stability
- White Color in options 220 grit and 325 grit
AM1016 Anti-Microbial Mildew Resistant Anti-Slip Epoxy Floor Coating – 3 Gal Kit
From: $210.00- Adds slip resistant finish to concrete floors
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Good for surfaces subject to bare foot traffic
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical and abrasion resistance
- Wide selection clear plus 20 colors
- Water base
AM253 Novolac Anti-Microbial Epoxy Resists Mildew Growth Acid Solvent Chemicals
From: $398.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Resists high concentration acids, some chlorinated solvents incl xylene, MEK
- High build for heavy duty traffic, chemical troughs, curbs
- Great for tanks, chemical spill areas
- Works on cement, masonry or brick
- Excellent adhesion 425 psi
- Quick back in-service, light foot traffic 10-18 hrs
- Low voc 47 g/L
AM257P Novolac Primer Anti-Microbial Epoxy Resists Mildew Growth Acid Solvent Chemicals
From: $325.52- Outstanding Spill & Splash Acid, Solvent, Chemical surface protection
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Excellent primer companion to AM253 Novolac Anti-Microbial Epoxy
- Resists wide range of chemicals, solvents, acids
- Excellent adhesion 375 psi
- Long working time 1 to 3 hour POT life
- Selection of 3 color options
AM322HW Anti-Microbial Mildew Resistant Aliphatic High-Gloss Urethane Low Temp 45°F
From: $212.00- Tough, durable high performance urethane
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Outstanding impact resistance 160 in lb (Gardner test)
- Excellent abrasion resistance 22 mg loss (Tabor test) Drops to 10 mg adding High Wear 325
- Excellent Chemical Resistance
- Aliphatic, UV Stable. will not yellow
- Easy to Use Long 2-4 Hour Pot Life
- Great for Indoor & Outdoor Projects
- Wide Variety of Clear and 18 Colors
- Solvent Based - Excellent adhesion
AM5015 Anti-Microbial Mildew Resistant Epoxy Primer WB
From: $94.00- Versatile epoxy primer for concrete, masonry, wood
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Available 20 Colors To Match Topcoat
- Excellent primer for epoxy, polyaspartic, urethane
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical & abrasion resistance
- Water base
AM707HB Anti-Microbial Mildew Resistant Epoxy Floor Coating | 100% Solids
From: $162.00- High Build - 100% Solids Commercial Epoxy
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Long POT Life (working time) 30-50 min
- Excellent Adhesion 450 psi
- Abrasion resistant Only 32 mg loss (Tabor test)
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
- Wide Variety of 20 Different Colors
Aspartic 100 High Build Polyaspartic for Concrete Floors | Low Temp 30°F | 100% Solids
From: $99.99- Tough, durable topcoat for interior epoxy floor coatings
- Very low to no odor great for sensitive odor indoor projects
- Can be used as high build topcoat up to 16 mils or 100 sq'/gallon
- Cold temperature application down to 30°F
- Excellent chemical and abrasion resistance
- UV Stable, Will Not Yellow
- Beautiful high gloss appearance
- Designed for high traffic and industrial areas
- High solids 100%
- Available clear & 14 colors (Pigment Sold Separate)
Aspartic 85 Polyaspartic Quick Cure Concrete Floor Coating | Low Temp 30°F
From: $79.50- Tough, durable topcoat for interior epoxy floor coatings
- Cold temperature application down to 30°F
- Fast Curing for quick 5-7 Hours Back in-Service Light Foot Traffic
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
- Designed for high traffic and industrial areas
- High solids 85%
- Available in clear & 14 colors (Colored Pigment Sold Separately)
Aspartic 85 Slow Set Polyaspartic Concrete Floor Coating | Low Temp 30°F | Low Odor Option
From: $99.99- Tough, durable topcoat for interior epoxy floor coatings
- Cold weather application down to 30°F
- Benefits of a Polyaspartic With Longer 45-60 minutes Working Times
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
- Designed for high traffic and industrial areas
- High solids 85%
- Available in clear & 14 colors (Colored Pigment Sold Separately)
- LOW ODOR version now available for indoor projects.
Brick Sealer and Water Repellent Premium Grade Brick Wall | Chimney | Patio
From: $27.00- Brick Sealer is a Specialty Premium Grade Water Repellent and Sealer Designed for Brick
- Prevents Damage From Wind Driven Rain
- Tough, Durable, Stain Resistant Natural Finish
- Protects Mortar From Moisture
- To 5 Year Satisfaction Guarantee
- Eco-Friendly and Easy To Apply
CLEAR-SEAL 100% Urethane High Gloss Super Premium Sealer
From: $167.00- High Gloss Super Premium Sealer
- Hot Tire Pickup & UV Resistant
- Great For Driveways, Walkways, Decks, Wall Murals
- Water Base, Low VOC, Eco-Friendly
- Chemical and Spill Resistant
- Excellent Adhesion
- Anti-Slip Finish Available
- For Concrete, Brick, Pavers, Stone, Unglazed Tile and Wood
- Specified by Architects in 099123, 099723, 099313
CLEAR-SEAL 100% Urethane Low Gloss Super Premium Sealer
From: $167.00- Low Gloss Super Premium Sealer
- Hot Tire Pickup & UV Resistant
- Great For Driveways, Walkways, Decks, Wall Murals
- Water Base, Low VOC, Eco-Friendly
- Chemical and Spill Resistant
- Excellent Adhesion
- Anti-Slip Finish Available
- For Concrete, Brick, Pavers, Stone, Unglazed Tile and Wood
- Specified by Architects in 099123, 099723, 099313
CLEAR-SEAL High Gloss Acrylic Urethane Sealer
From: $75.00- High Gloss Premium Sealer
- Hot Tire Pickup & UV Resistant
- Great For Driveways, Walkways, Decks, Wall Murals
- Water Base, Low VOC, Eco-Friendly
- 5 Year Labor & Material Warranty
- Specified by Architects in 099123
CLEAR-SEAL Low Gloss Acrylic Urethane Sealer
From: $80.00- Low Gloss Premium Sealer
- Hot Tire Pickup & UV Resistant
- Great For Driveways, Walkways, Decks, Wall Murals
- Water Base, Low VOC, Eco-Friendly
- 5 Year Labor & Material Warranty
- Specified by Architects in 099123
CMW 8000 Lithium Moisture Vapor Barrier and Concrete Densifier
From: $54.00- Deep Penetrating Concrete Vapor Barrier
- Reduce Hydrostatic Vapor Pressure on Concrete Floors
- Prevent Damage to Floor Coatings and Flooring
- Densifier Adds 20% - 40% Strength to Concrete
- Helps Stops Efflorscence and Concrete Dusting
- Permanent One Time Application
CoatZF ESD Low-VOC Dissipative Clear Floor Finish | Static Control | ESD and Non-ESD Floors | 5 Gall...
$450.00- Zinc-free
- Static dissipative (1 x 10E6 to < 1 x 10E10 ohms) Coating - ANSI/ESD STM7.1 and ESD TR53
- Low tribocharging (<100 volts) coating - ANSI/ESD STM97.2
- 23% Solids- 2 Coat System** Reduces labor needed for initial install and on-going maintenance of the floor
- Hard, wear resistant – ASTM Standard D2134.93
- UL listed for slip resistance
Concrete Sealer and Water Repellent Premium Grade Clear Protection
From: $43.00- Concrete Sealer is a Specialty Premium Grade Water Repellent and Sealer Designed for Concrete
- Protects Against Winter Salt & Freeze/Thaw
- Prevents Damage From Wind Driven Rain
- Tough, Durable, Stain Resistant Natural Finish
- Protects Mortar From Moisture
- To 5 Year Satisfaction Guarantee
- Eco-Friendly and Easy To Apply
DT-454 Epoxy Quick Cure UV Concrete Floor Coating Low Temp 40F | 100% Solids
From: $71.00- Tough, Durable Epoxy Coating
- Quick cure 6-7 hour recoat time
- Outstanding Bonding
- UV Resistant
- Good chemical, impact and abrasion resistance
- Cold temperature application down to 40F
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 14 colors! (Pigment sold separately)
E-Green Polyurea Basecoat for Concrete Floors | Low Temp 40°F | 100% Solids | 300% Elongation
From: $65.00- Tough, durable plant based Polyurea Coating
- Extreme Flexibility (300% Elongation)
- Exceptional Adhesion >500 psi ASTM D4541
- Cold temperature application down to 0°F
- Can be used as high build basecoat up to 16 mils or 100 sq'/gallon
- Excellent chemical and abrasion resistance
- Designed for high traffic and industrial areas
- 100% Solids Performance
- Available in clear & 14 colors!
- Quick Cure 1 Day System
- Little to NO ODOR
E-Poly Pigment For All Floorguard Epoxy & Polyaspartic Coatings
From: $52.00- Universal E-Poly Pigment Designed to Color All Epoxy & Polyaspartic Coatings manufactured by Floorguard Products
- Add a Beautiful Decorative Color to Your Epoxy Project
- 14 Different Colors to Choose From!
- Sold in Quart Containers - Typically colors 3-5 Gallons When Mixed Into Clear Epoxy or Polyaspartic
- Pigment can be Pre-mixed into Floorguard Epoxy & Polyaspasrtic Coatings on all orders 60 gallons or more with 4-7 days lead time (when ordered in 10 or 15 gallon kits as appropriate)
E100 Urethane Primer Finish Coat | Aluminum Galvanized & Rusty Steel | Dry Heat to 400 °F | App...
From: $55.00- Prime over Steel, metal, weathered galvanized steel, aluminum, fiberglass, polyurethane foam and previously painted surfaces
- Excellent “wetting out” properties and performance over sound rusty surfaces
- Outstanding abrasion & chemical resistance
- Very good weather resistance
- Excellent corrosion resistance, passed 1,200 hrs in salt cabinet
- Fast recoat 1-2 hours at 75°F & 50% R.H
- Cures down to 18°F and apply up to 140°F
- High heat resistance to 400°F dry
- Single component, easy to use
- Topcoat with most Epoxy, Urethane Alkyds, Silicone, Enamels and Acrylic
- Excellent barrier coat over lead based coatings
- USDA Approved
E1016 Anti-Slip Epoxy Concrete Floor Coating – 3 Gal Kit
From: $196.00- Adds a slip resistant finish to concrete floors
- Good for use on surfaces subject to bare foot traffic
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical and abrasion resistance
- Wide selection of clear plus 20 color options
- Water base
E101C Moisture Cured Urethane Clear Heavy Traffic Floor Sealer | Dustproofer | Prevents Spalling
$85.00- Great heavy duty stain resistant floor sealer for warehouse and other heavy use areas
- Excellent adhesion and sealer for concrete, wood and masonry surfaces.
- Extremely hard, yet flexible film.
- Outstanding “wearing properties
- Highly resistant to abrasion and impact.
- Excellent stain resistance.
- Keeps concrete dusting down.
- Good chemical resistance.
- Easy to clean and maintain.
- Quick recoat as soon as 1-2 hours
- One component, easy to use - No mixing 1-2 hour POT Life.
E105M Epoxy Mortar Concrete Resurfacer & Patch Kit
From: $66.00- Economical Easy resurfacing old and damaged concrete floors
- Compressive Strength 8,400 psi ASTM D695
- Heat Deflection Temp 131.7F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- 100% solids epoxy
- Comes complete with epoxy & aggregate
- Selection of 5 color options
- Application temp range 55°F to 90°F
E110M Epoxy Mortar Concrete Premium Resurfacer & Patch Kit
From: $73.00- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- 10% greater coverage/unit vs E105M Epoxy Mortar
- Compressive Strength 11,150 psi ASTM D695
- Heat Deflection Temp 158.9F ASTM D648
- High Build Resurfacing 1/8" to 1"
- Spot Patching up to 2" - 3" thick
- Long 30-40 min POT Life
- 100% solids epoxy
- Comes complete with epoxy and aggregate
- Selection of 5 color options
- Application temp range 55°F to 90°F
E126CW Cold Weather Epoxy Mortar Concrete Resurfacer & Patch Kit 35°F to 80°F
From: $71.00- Great for Cold Weather & Cold Storage Facilities
- Application range 35°F to 80°F
- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- Compressive Strength 11,284 psi ASTM D695
- Heat Deflection Temp 149.9F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- 100% solids epoxy
- Comes complete with epoxy and aggregate
- Selection of 5 color option
E128AF Arctic Epoxy Mortar Concrete Patch Kit | Cold Condition -10°F to 40°F
From: $70.00- Tough, Durable Cold Winter Weather Concrete Patch & Repair
- Excellent Extreme Cold Condition Patching -10°F to 40°F
- Great For Freezer, Cold Storage and Outdoor Winter Repairs
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- Excellent chemical resistance
- Excellent Abrasion and Impact Resistance
- Compressive Strength 11,000 psi ASTM D695
- Quick recoat 1-2 hrs & 2-4 hrs light foot traffic
- Selection of 3 color options
- Easy to Use 3 part kit Includes Silica Sand or Liquid Only
E130A Oil Contaminated Concrete & Asphalt Epoxy Mortar Patch Kit/Resurfacer
From: $66.00- Great for patching and repairing oil contaminated and damaged concrete
- Can be used to patch and repair asphalt surfaces
- Can be applied up to 1/8" one application
- Crack. holes and general surface repairs
- Excellent abrasion and impact resistance
- 100% solids
- Easy to Use 3 part kit Includes Silica Sand or Liquid Only
E139FL Flexible Epoxy Primer & Floor Coating | 60% Elongation | 100% Solids | Indoor & Out...
From: $65.00- Exceptionally flexible epoxy with 60% elongation
- High Build up to 50 mils thick per coat
- 100% Solids Commercial Epoxy
- Excellent Adhesion 450 psi
- Tough Abrasion resistant Only 6 mg loss (Tabor test) and 160 inch lbs Gardner variable impact test
- For use with broadcast systems and as flexible membrane primer
- Wide Variety of 15 Colors
E1409CL Moisture Vapor Barrier Epoxy Sealer Primer For Concrete ASTM F3010
From: $247.00- Reduce effects of moisture vapor transmission on concrete floors
- Control moisture vapor emission rates to 20 lb/24hr/1000 sq' (ASTM F1869)
- Used as Sealer/Primer to protect Polymeric coating systems, vinyl sheets, tile, cementitious overlays, terrazo, wood veneers, and carpet
- 100% solids with 0 voc
- Easy to apply with one coat most projects
- Meets ASTM F3010 for vapor permeance at the recommended thickness
E1500HN Novolac Epoxy | Superior Steel & Concrete Chemical Horizontal Protection | Secondary Co...
$340.00- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
- Great horizontal chemical protection for Secondary Containment for both steel and concrete surfaces
- Thin film self leveling to 40 mils DFT one coat
- Extremely tough with high wearing properties
- Excellent abrasion resistance and impact resistance
- Meets USDA requirements
E15M Epoxy Mastic Steel Primer DTM & Concrete Coating | Chemical Resistant | Low Temp 25F
From: $95.00- High solids DTM (direct-to-metal) chemical resistant steel primer or finish coat to steel and concrete
- Self priming to steel including tight rust
- Apply Vertical Surfaces to 8 mils DFT Steel & Concrete
- Great primer for use with our E1500HN (horizontal) and E555VN (vertical) Novolac Chemical Resistant Epoxies
- USDA Approved
- Tight film, low permeability.
- Exceptional adhesion Exceeds 500 psi
- Excellent impact resistance 90 in lb
- Excellent abrasion resistance CS 17 Wheel, 1000 cycles, 1000 g Load 21 mg loss
- Excellent against rust “undercutting”
- Easy to apply brush, roll and spray
- Low temp cure version to 25°F
- Available 13 colors
E183HB Epoxy Floor Coating High Build | Quick Back In-Service | Abrasion & Chemical Resistant |...
From: $324.00- High Build - Impact & Chemical Resistant
- Quick back in-service light foot traffic 8-14 hrs
- Full chemical resistance only 3 days
- Excellent Adhesion 450 psi
- Abrasion resistant Only 23 mg loss (Tabor test)
- Excellent Chemical Resistance
- High build apply 10 to 20 mils one coat (80 - 160 sq'/gal)
- Wide Variety of 19 Different Colors
E322HW High-Gloss Aliphatic Urethane Abrasion & Chemical Resistant Low Temp 45°F
From: $60.00- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Cold temperature application down to 45°F
- Excellent abrasion resistance Only 22 mg loss (Tabor Abrasion test) Reduced to 10 mg loss using our High Wear 325 additive
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
- Easy to Use with Long 2-4 Hour Pot Life
- Great for both Indoor and Outdoor Concrete Floor Projects
- Comes in wide Variety of Clear and 18 Different Colors
- Solvent Based - Excellent adhesion
E322SG Semi-Gloss Aliphatic Urethane Abrasion & Chemical Resistant Low Temp 45°F
From: $60.00- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Cold temperature application down to 45°F
- Excellent abrasion resistance Only 24 mg loss (Tabor Abrasion test) Reduced to 12 mg loss using our High Wear 325 additive
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
- Easy to Use with Long 2-4 Hour Pot Life
- Great for both Indoor and Outdoor Concrete Floor Projects
- Comes in wide Variety of Clear and 18 Different Colors
- Solvent Based - Excellent adhesion
E344QC Polyaspartic Quick Cure Concrete Floor Coating | 85% Solids
From: $73.00- Tough, durable topcoat for interior epoxy floor coatings
- Fast Curing for quick back in-service
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
- Designed for high traffic and industrial areas
- High solids 85%
- Available in clear & 13 colors (Colored Pigment Sold Separately)
E352P Hi-Gloss Polyester Polyurethane Floor Coating | Chemical Abrasion Resistant | Exterior Interio...
From: $205.00- Great Interior & Exterior Horizontal Concrete & Steel Protection
- Exceptional Exterior Durability
- Excellent weather resistance
- Non-chalking and non-yellowing with excellent gloss and color retention
- Extremely tough, yet flexible
- A tile-like finish.
- Easy to clean
- Excellent chemical and stain resistance
- Highly resistant to abrasion and impact
- Outstanding wearing properties
- Handles up to 250°F Dry Service
- Long 4 hour POT life @ 75ºF
- Available in clear and 11 colors
E356HG High Gloss Urethane Moisture Cured | Exceptional Abrasion & Chemical Resistance | UV Sta...
From: $70.00- Superior abrasion resistance Only 4.4 mg loss (Tabor Abrasion test)
- Outstanding Chemical Resistance
- Excellent durability with impact resistance of 100 in lb (Gardner Impact test)
- Aliphatic, UV Stable and will not yellow
- Easy to Use one part with Long 3-5 Hour Pot Life
- Great for both Indoor and Outdoor Concrete Floor Projects
- Solvent Based With Excellent adhesion
E370P Hi-Gloss Hi Build Polyurethane | Non-Yellowing | For Vertical Concrete and Steel | Walls
From: $118.00- Great Interior & Exterior Vertical Concrete & Steel Protection
- Exceptional Exterior Durability
- High solids
- Tile-like finish.
- Easy to clean
- Good chemical and stain resistance
- Highly resistant to abrasion and impact.
- Excellent gloss and color retention to UV exposure
- Pass 2500 hrs - QUV Accelerated Weathering ASTM D4587
- Outstanding wearing properties.
- Non-chalking and non-yellowing
- High film build
- Handles up to 300°F Dry Service
- Long 4-6 hour POT life @ 75ºF
- Available in clear and 21 colors
E449 Polyaspartic Fast Cure High Gloss Concrete Floor Coating | 95% High Solids
From: $73.00- Tough, durable topcoat for epoxy floor coatings
- High solids 95%
- Quick back in service 3-5 hours light foot traffic
- Can be applied up 12 mils thick one coat (125 sq'/gallon)
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
- Designed for high traffic and industrial areas
- Available in clear & 13 colors (Colored Pigment Sold Separately)
E450SF Polyaspartic Slow Cure High Gloss Concrete Floor Coating | 90% Solids (Formerly E449SF)
From: $80.00- Tough, durable topcoat for interior epoxy floor coatings
- High solids 90%
- Can be applied up 12 mils thick one coat (120 sq'/gallon)
- Long Working time 20-25 min
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
- Designed for high traffic and industrial areas
- Available in clear & 13 colors (Colored Pigment Sold Separately)
E5013 Fast Set Clear Epoxy Primer WB Concrete | Wood | Masonry
From: $60.00- Versatile product good on concrete, masonry, wood surfaces
- Quick 4-6 hour Recoat for same day projects
- Excellent as clear primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Long 2 hour pot life
- Excellent adhesion 425 psi
- Good chemical and abrasion resistance
- Water base
E5015 Epoxy Primer WB Coating | Concrete Wood Masonry | 20 Colors
From: $51.00- Versatile product good on concrete, masonry, wood surfaces
- Excellent as primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Available in Clear and 20 Colors To Match With Topcoat
- Long 1 - 1.5 hour pot life
- Excellent adhesion 425 psi
- Good chemical and abrasion resistance
- Water base
E5030CL Urethane Clear Sealer / Topcoat WB
From: $55.00- Attractive, clear aliphatic non yellowing finish
- Versatile product good on concrete and masonry surfaces
- Recoat only 1-2 hours & light foot traffic 2-4 hours
- Extended 24 hour pot life
- Excellent abrasion resistance (Taber Abrasor test only 10 mg loss)
- High Gloss (>80 at 60 degrees)
- Flexible (120% Elongation at break)
- Water based
E517M Flake Filled Epoxy Mastic Steel & Concrete Coating | Chemical Containment | Low Temp 25F
From: $125.00- Self Priming on steel
- Excellent primary containment coating for internal tank linings (when part of specified system)
- Excellent secondary containment coating
- Performs well over epoxy mortars and properly primed concrete surfaces
- Can be applied on damp surfaces
- Excellent chemical resistance to acids, caustics, solvents
- Outstanding impact and abrasion resistance.
- Exceptional adhesion Exceeds 700 psi
- Excellent flexibility pass 7/8" mandrel 180º Bend
- Apply Vertical Surfaces to 15 mils one coat
- Meets USDA requirements.
- Low temp cure version to 25°F
- Low VOC 72 grams/Liter
E5520 Low Gloss Urethane Water Base Abrasion & Chemical Resistant
From: $64.00- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Excellent abrasion resistance Only 23 mg loss (Tabor Abrasion test) Reduced to as low as 10 mg loss using our High Wear 325 additive
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
- Great for both Indoor and Outdoor Concrete Floor Projects
- Very Low voc 35 g/L, water based formula
E555VN Novolac Epoxy | Superior Steel & Concrete Chemical Vertical Protection | Tank Linings
$142.00- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
- Vertical application to 10 mils DFT.
- Great for Secondary Containment for both steel and concrete surfaces
- Use as Primary Containment and Tank Linings when used as part of specified system
- Excellent abrasion resistance with ceramic filler
- Excellent in battery storage room areas.
- Meets USDA requirements
- May be applied in cold, damp conditions to 45°F with curing down to 35°F
E572500 Non-Slip Skidproofer High Performance Epoxy Coating
From: $131.00- Great protection for problem slippery or wet concrete areas
- Outstanding slip resistance with a very aggressive textured anti-slip profile
- Excellent chemical and abrasion resistance
- Designed for high traffic and industrial areas
- Good For Docks, Ramps, Walkways etc
- 100% solids, 2 component
E57936 Lithium Concrete Densifier | Deep Penetrating
From: $40.00- Increases durability by improving resistance to freeze thaw effects
- Improves abrasion resistance and durability.
- Improves weathering, densifies and reduces efflorescence of natural stone, precast stone and cement.
- Protects and fortifies concrete as it seals against moisture damage.
- Application will reduce dusting and increase concrete life
E57937 Lithium Concrete Densifier Extra Strength | Deep Penetrating
From: $49.00- Increases durability by improving resistance to freeze thaw effects
- Improves abrasion resistance and durability.
- Improves weathering, densifies and reduces efflorescence of natural stone, precast stone and cement.
- Protects and fortifies concrete as it seals against moisture damage.
- Application will reduce concrete dusting and increase concrete life
- Extra Strength formula for improved performance
- Comes in both ready-to-use and money saving concentrate options
E57940 Concrete Conditioner With Stain Guard
From: $60.00- Increases durability by improving resistance to freeze thaw effects
- Improves abrasion resistance and durability.
- Improves weathering, densifies and reduces efflorescence of natural stone, precast stone and cement.
- Protects and fortifies concrete as it seals against moisture damage.
- Application will reduce dusting and increase concrete life
E5820 Oil Stop Epoxy Concrete Primer / Coating For Oil Contamination Areas
From: $50.00- Great for coating over oil contaminated concrete
- Can use as a primer before applying decorative coating systems
- Good as stand alone black colored coating
- Excellent substrate penetration through oil contaminated surfaces
- Excellent adhesion where standard epoxies typically fail
- Long 1 - 2 hour pot life
- High solids, 2 component
E591 Wet Surface Epoxy | Apply Underwater | Cures to 35°F | Concrete – Steel | Floors – ...
From: $120.00- May be applied on wet or under water surfaces
- Cold temperature application down to 35°F
- Self-priming on steel and on most concrete applications
- Long 40-50 POT Life at 75F
- Ideal for marginally prepared and painted surfaces
- Outstanding impact and abrasion
- High film build - Up to 20 mil DFT per coat on horizontal surfaces
- Vertical surfaces to 12 mils
- Excellent coating for manholes
- 100% solids and 0 g/L VOC's
- 3 Colors Available
E650 Non-Skid Epoxy Floor & Deck Low Temp 25°F | OSHA ADA Navy Spec Mil-PRF-24667B
From: $107.00- Heavy duty non-skid resistance for concrete & steel
- Available in fast cure, cold temp formula to 25°F
- Designed for wet areas
- Meets ADA and OSHA requirements for safe co-efficient of friction (COF) when properly applied
- Meets Navy Military Specification Mil-PRF-24667B for Non-Skid Deck Coatings
- Excellent adhesion, abrasion and impact resistance
- Resistant to grease, oil, salt water, alcohol, detergent, gasoline, hydraulic fluid
- Excellent coating for Diamond Plate
- Easy to apply, ready to use non-skid coating
- Comes in 4 colors
E671CL Epoxy Floor Coating | Clear | 100% Solids | For Metallic Pigment and Full Flake & Quartz...
From: $52.00- Clear epoxy great for use with metallic pigments and full flake or quartz broadcast systems
- High Build - 100% Solids Commercial Epoxy
- Good Adhesion 350 psi
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
E700HV Epoxy | Exceptionally Tough | Abrasion & Chemical Resistant | No Topcoat Required
From: $64.00- Saves Money - Eliminates Need for Urethane or Polyaspartic Topcoat
- Extremely Tough D-90 Shore Hardness
- Exceptional Abrasion resistance Only 19 mg loss (Tabor test)
- Excellent Adhesion 420 psi
- Good Chemical Resistance
- Great Looking Very High gloss (80-105 at 60 degrees @ glossmeter)
- 97% Solids Commercial Epoxy
- High build 15-30 mils one coat (53 - 106 sq'/gal)
- Wide Variety of 20 Colors
E707HB High Build 100% Solids Epoxy Floor Coating | 20 Colors
From: $55.00- High Build - 100% Solids Commercial Epoxy
- Long POT Life (working time) 30-50 min
- Excellent Adhesion 450 psi
- Abrasion resistant Only 32 mg loss (Tabor test)
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
- Wide Variety 20 Different Colors
E707LVP High Solids Epoxy Primer & Base Coat | Helps Prevent Outgassing | 20 Colors
From: $54.00- High Solids Commercial Grade Epoxy Primer
- Helps reduce problems from concrete outgassing (air bubbles)
- Long POT Life (working time) 35-55 min
- Excellent Adhesion 430 psi
- Good Chemical Resistance
- Wide Variety 20 Different Colors
E814R Co-Polymer Liquid Rubber Roof Walkway Coating | Slip Resistant
From: $76.00- Exceptionally tough, durable one part waterproof roof walkway
- Offers excellent anti-slip walking surface
- Excellent adhesion EPDM, APP, TPO, Hypalon, Concrete, Wood, Metal
- Available in 12 colors
- Excellent waterproof with E96 Vapor Transmission Class I 0.025 perms and Water Absorption 0.04%
- Excellent weathering
- Excellent UV stability
- Good resistance to dirt pickup
- Excellent low temp flexibility with 500%+ Elongation
- Resists mildew and fungi growth
- Good resistance to Alkalis and acids
E903M Urethane Cement High Build Mortar | Wet Heat to 200F | Hot Oil & Water Wash | Resist Fung...
From: $200.00- Excellent heat and thermal shock resistance to 200F
- Very good chemical resistance to organic and inorganic acids and solvents
- Resistant to Fungi Growth: Passes rating of 1 @ ASTM G-21
- Seamless hygienic finish with no grout lines
- High build repairs to 1"
- Excellent bonding characteristics
- Low odor, fast installation and fast cure.
- Low temp application down to 45F
- Available 3 colors gray, tan and tile red
E903SL Urethane Slurry | High Wet Heat 200F | Hot Oil & Water Wash | Moisture & Fungi Resi...
From: $100.00- Excellent heat and thermal shock resistance to 200F wet heat
- Very good chemical resistance to organic and inorganic acids and solvents
- Excellent Moisture vapor transmission to 12 pounds per 1,000 sq. ft. over a 24 hour period as per ASTM E1907
- Resistant to Fungi Growth: Passes rating of 1 @ ASTM G-21
- Good anti-skid surface
- Excellent bonding characteristics
- Great protection for food and beverage industry, food processing plants, dairy farms, industrial kitchens and wine cellars.
- Low temp application down to 45F
- Available 3 colors gray, tan and tile red and 2 package sizes
- E903SL Urethane Slurry is the high performance basecoat to the E903TC Urethane Top Coat high heat System
E903TC Urethane Topcoat | High Wet Heat 200F | Hot Oil & Water Wash | Moisture & Fungi Res...
From: $100.00- Excellent heat and thermal shock resistance to 200F wet heat
- Very good chemical resistance to organic and inorganic acids and solvents
- Excellent Moisture vapor transmission to 12 pounds per 1,000 sq. ft. over a 24 hour period as per ASTM E1907
- Resistant to Fungi Growth: Passes rating of 1 @ ASTM G-21
- Good anti-slip surface
- Excellent bonding characteristics
- Great protection for food and beverage industry, food processing plants, dairy farms, industrial kitchens and wine cellars.
- Low temp application down to 45F
- Available 3 colors gray, tan and tile red
- E903TC Urethane is the high performance topcoat to the E903SL Urethane high heat Slurry System
E903UCB Cove Base Urethane Mortar | HIgh Heat 250F | Anti-Fungal
From: $87.00- Easy construction of vertical cove bases
- Seamless hygienic finish with no grout lines
- Resistant fo fungi growth
- Low odor, fast installation, fast cure
- Thermal shock to 250F & chemical resistance
- 3 color options
Floor-lok Concrete Floor Sealer and Curing Aid Concentrate
$170.00- Concrete Floor Sealer, Dustproofer, Curing Aid
- Clear Silane Siloxane Formula
- Penetrating Leaves No Film
- Will Not Yellow
- Water Base, Low VOC, Eco-Friendly
- 1 Year Labor / Material Warranty
- Specified by Architects in 099123
Gloss Sealer For Masonry and Wood | Premium Grade Acrylic
From: $42.00- Premium Grade Sealer and Water Repellent Offering a Nice Glossy Look
- For Concrete, Masonry, Brick, Wood
- Use on Painted or Unpainted Surfaces
- Adds Stain Resistance for Easier Cleanup
- Clear Finish Will Not Yellow
- To 5 Year Satisfaction Guarantee
- Eco-Friendly and Easy To Apply
GroundWorx SF ESD Static Conductive Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014
From: $960.00- Conductive 2 Part Water Based Thin Film Epoxy Floor Coating
- Conductive range 2.5 x 104 - 3.5 x 107 ohms
- System Resistance (w/ ESD Footware) < 3.5 x 107 (fully compliant) ANSI/ESD STM 97.1
- Warrantied ANSI S20.20 performance
- Meets ANSI/ESD S20.20-2014 (S97.1 and S97.2), DOD 4145.26M, HDBK263A
- Easy to Install
- For Concrete, Wood, VCT Tile Floors
- Use in Electronics Mfg, Assembly, ESD Protected Areas
- 6 Colors. Pewter Gray Color available for immediate shipment
GroundWorx Ultra (HB-97.2) ESD Static Conductive Epoxy Primer 100% Solids | Forklift Traffic | ANSI/...
From: $555.00- Static dissipative or conductive high build epoxy electrical protection when used with the GroundWorx Ultra ESD Urethane Topcoat which comes in either dissipative >1.0 x 10e6 ohms or conductive <1.0 x 10e6 ohms electrical resistance, limiting Static Charge Generation to <15 volts
- Great for high traffic, high wear commercial & industrial applications as high build 14 mil ESD system at <$4.00/sq' material cost
- Use on Concrete, Wood and old VCT surfaces
- Moisture tolerant primer
- Excellent adhesion 350 psi
- 100% solids, 0 g/L voc
- Conforms to ESDA, ANSI standard S20.20-2014 when used with GroundWorx Ultra ESD Urethane Topcoat
- Gloss sheen
- 8 standard colors & custom colors available
H20 HyperPRIME Epoxy Quick Cure Bonding Primer | Low Temp 45°F | 1 Hr Recoat
$347.00- Excellent Substrate Penetration with superior adhesion 450 psi
- Great for concrete, wood and metal surfaces
- Helps protect Against Coating Damage from Outgassing of Concrete
- Quick Cure With 1 Hour Recoat Time - great for 1 day floor coating systems
- Available in Clear plus 6 Colors
- Water Base, No Offensive odors
- Cold temperature application down to 45F
- Good chemical and Stain Resistance
- Easy Application
- Available in Clear and 4 colors
H20 zioTHANE Low Gloss Urethane Concrete Floor Sealer / Topcoat
From: $89.00- Tough, Durable Concrete Floor Sealer
- Topcoat for Epoxy Floor Coatings
- Excellent Chemical and Abrasion Resistance
- Exceptional Impact Resistance
- Aliphatic, UV Stable and Will Not Yellow
- Beautiful Clear, Low Gloss Appearance
- Designed for High Traffic and Industrial Areas
- Water Based, Low voc <10 g/L
H20 ZioTHANE Semi-Gloss Urethane Concrete Floor Sealer/Topcoat
From: $89.00- Tough, Durable Concrete Floor Sealer
- Topcoat for Epoxy Floor Coatings
- Excellent Chemical and Abrasion Resistance
- Exceptional Impact Resistance
- Aliphatic, UV Stable and Will Not Yellow
- Beautiful Clear, High Gloss Appearance
- Designed for High Traffic and Industrial Areas
- Water Based, Low voc <10 g/L
HyperBOND Moisture Tolerant Epoxy Concrete Floor Coating | Low Temp 40F | 100% Solids
From: $69.00- Tough, Durable Epoxy Coating
- Outstanding Bonding
- Cold temperature application down to 40°F
- Water Insensitive and Can Be Applied In Wet Conditions
- Withstands up to 9 lbs. of hydrostatic pressure for use in areas with moisture.
- Resistant to Blushing/Sweating
- Good chemical, impact and abrasion resistance
- High solids 100%
- Available in clear & 14 colors! (Pigment sold separately)
HyperCRETE Urethane Slurry | High Wet Heat 200F & Dry Heat 300F | Hot Oil & Water Wash
$265.00- Excellent heat and thermal shock resistance
- Very good chemical resistance to organic and inorganic acids and solvents
- Quick 4 hour recoat and 12 hour full service times
- Works great for commercial kitchens and industrial areas subject to hot water and hot oil spills
- Excellent bonding characteristics
- Rapid curing and harnders
- No VOC's and no odor
- Low temp application down to 45F
- Available 2 colors tile red and gray
HyperCURE Concrete Repair Kit | Flexible | Quick Cure
$165.00- Superior Flexibility and Outstanding Bonding
- Fast Cure - 15 to 30 min recoat
- High Hardness
- High Tensile & Tear Strength
- Tough, Durable Epoxy Concrete Crack Repair, Holes, Spalls and Control Joint Filler
- Rapid Cure Rate For Same Day System Application
HyperFLEX Epoxy | Flexible Membrane Concrete Wood | Low Temp 40°F | 100% Solids
From: $74.00- Tough, Durable Epoxy Coating and Flexible Membrane
- Very Flexible with Elongation rating 150% @ASTM D-638
- Great for Quick Crack Repair and Control Joint Filler (when mixed with Fumed Silica)
- Can be used as a (1) basecoat for full broadcast floors, (2) flexible membrane, (3) repair gel to fill joints, cracks, & divots
- Cold temperature application down to 40°F
- Concrete & Wood Floors and Countertops
- Superior Flexibility and Outstanding Bonding
- Rapid Cure Rate For Same Day Flake and Solid Color System Application
- When used as membrane or basecoat HyperFLEX cures about 2 hours
- When used for gel repair cures about 10-15 minutes
- Good chemical and abrasion resistance
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 14 colors! (Pigment sold separately)
HyperREZ UV Low Temp 40°F High Build Epoxy Concrete Floor Coating | 100% Solids
From: $74.00- Tough, durable epoxy floor and countertop coating
- Cold temperature application down to 40F
- High Build Applications up to 32 mils/coat (50 sq'/gal)
- Long Working Time
- Good chemical and abrasion resistance
- UV Resistant
- High gloss appearance
- Designed for high traffic and industrial areas
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 14 colors (Colored Pigment Sold Separately)
Metallic Epoxy Color Pigment | Marbled 3-D Look | Pearlescent | Translucent 4oz (113g)
From: $19.99- Create a Beautiful Metallics Epoxy Floor System
- Vibrant and Exciting Pearlescent looking colors
- 3 Dimensional Marbled Appearance
- Unlimited Designs - Endless Possibilities
- 50 Different UV Resistant Colors
- See our 5 new Color Shifting, unique Multi-Colored pigments
- Add Metallics Pigment to HyerREZ UV Epoxy Or E671CL Epoxy as Part of 3 Step System
- Floor & Countertop projects on concrete and wood
- Pigment ships as Powder in Easy to Use 4 oz Container
Micro-seal Silane Siloxane Water Repellent | Concrete Brick Block Stucco
From: $33.00- Best in Class Multi-Surface Moisture Protection
- Used on Construction Projects Worldwide
- ASTM Tested to Stop 98 mph Wind Driven Rain
- Clear Penetrating, No Change in Appearance
- 10 to 20 Year Labor / Material Warranty
- Water Base, Low VOC, Eco-Friendly
- Specified by Architects in 03300, 04220, 07190, 099123, 09960
MV2112 Moisture Vapor Barrier Primer Epoxy For Concrete Floors | ASTM F3010
From: $105.00- Reduce effects of moisture vapor transmission on concrete floors
- Control moisture vapor emission rates to 20 lb/24hr/1000 sq’ (ASTM F1869) or between 75% and 95% for ASTM F2170
- Superior moisture vapor control
- Class I Vapor Diffusion Retarder with perm rating of <.10
- Primer to protect Polymeric coating systems, vinyl sheets, tile, cementitious overlays, terrazo, wood veneers, and carpet
- 100% solids with 0 voc
- Meets ASTM F3010 for vapor permeance at the recommended thickness
NE253 Novolac Colored Epoxy Acid Solvent Chemical Resistant High Build
From: $55.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Resistant to high concentration acids, some chlorinated solvents incl xylene, MEK
- Resists wide range of chemicals, solvents and acids
- High build for heavy duty traffic projects, chemical troughs and curbs
- Great for tanks and chemical spill areas for cement, masonry or brick
- Excellent adhesion 425 psi
- Quick back in-service, light foot traffic 10-18 hrs
- Selection of 3 color options
- Low voc 47 g/L
NE253SL Novolac Epoxy Colored Slurry Acid Chemical Resistant Floor Coating
From: $55.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Apply to 1/16" thick to resurface traffic, chemical spill areas
- Resists wide range of chemicals, solvents and acids
- Resistant to high concentrations of acids and even some chlorinated solvents incl xylene, MEK
- Excellent adhesion 425 psi
- Quick back in-service with light foot traffic 10-18 hours
- Selection of 3 color options
- Low voc 22 g/L
NE253V Novolac Vertical Wall Colored Epoxy Chemical Resistant Acid Solvent
From: $55.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Resistant to high concentration acids, some chlorinated solvents incl xylene, MEK
- Apply up to 10 mils on vertical walls
- Resists wide range of chemicals, solvents and acids
- Medium build for chemical troughs and curbs
- Great for tanks and chemical spill areas for cement, masonry or brick
- Excellent adhesion 425 psi
- Quick recoat 5-10 hrs
- Selection of 3 color options
- Low voc <40 g/L
NE255P Novolac Epoxy Primer/Sealer Flexible Crack Bridging Chemical Resistant
From: $55.00- Excellent crack bridging, flexible high build primer eliminates need to repair hairline cracks in chemical exposure areas
- Use for priming light to medium duty secondary containment
- Tough, durable coating for surfaces exposed to vehicle traffic
- Outstanding abrasion and impact resistance with only 5 mg loss Taber Abrasion test and 100 inch lbs Gardner Impact Test
- Excellent adhesion 450 psi
- 100% solids, zero voc 0 g/L
NE256 Novolac Clear Epoxy Acid Solvent Chemical Resistant Floor Coating
From: $55.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Exceptional resistance to wide range of chemicals, solvents and acids
- Medium to High build for chemical spill areas, troughs, curbs and tanks
- Use as clear color coating or base for chip/flake or aggregate systems
- Excellent adhesion 400 psi
- Low voc <31 g/L
NE256M Novolac Epoxy Mortar Acid Solvent Chemical Resistant Patch Kit/Resurfacer
From: $83.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Apply at 1/8" to 1/4" to resurface traffic and chemical spill areas
- Used in many chemical immersion projects, curbs, tanks and chemical troughs
- Resists wide range of chemicals, solvents and acids
- Excellent impact and abrasion resistance
- Selection of 4 color options
- Low voc <14 g/L
NE258P Novolac Epoxy Clear Primer Acid Solvent Chemical Resistant Floor Coating
From: $55.00- Excellent primer companion to our NE256 Novolac Clear Epoxy topcoat
- Helps reduce air release generation when applying higher solids novolac topcoats
- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Resists wide range of chemicals, solvents and acids
- Excellent adhesion 365 psi
- Long working time with 1 to 3 hour POT life
NE259G Novolac Epoxy Grout Coat Acid Solvent Chemical Resistant Floor Coating
From: $55.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Resists wide range of chemicals, solvents and acids
- Low build epoxy to seal surface of existing mortar overlay system
- Great for topcoating/sealing poxy mortar power trowled or hand trowled systems
- Excellent adhesion 425 psi
- Selection of 3 color options
- Low voc <47 g/L
NE5928 Interior Expansion & Flexible Joint Novolac Chemical Sealant
From: $146.00- Flexible joint filler - Elongation 43.4% at 70F (ASTM D-412)
- Outstanding chemical and impact resistance
- Novolac epoxy urethane hybrid formula
- Excellent adhesion 420 psi
- 100% solids with 0 voc
- Low odor
- Paintable surface
NE5928V Vertical Interior Expansion & Flexible Joint Novolac Chemical Sealant
From: $145.00- Flexible vertical joint filler - Elongation 43.4% at 70F (ASTM D-412)
- No sag formula for vertical interior wall and overhead applications
- Outstanding chemical resistance
- Novolac epoxy and urethane hybrid formula
- Excellent impact resistance
- Good adhesion 380 psi
- 100% solids with 0 voc
- Low odor
- Paintable surface
NP-1 Cove Master Vertical Epoxy Mortar | 100% Solids | High Build | 4 Colors
From: $56.00- Easy construction of vertical cove bases
- 100% Solids Commercial Grade Epoxy
- High build formula
- 5 color options
- Comes as 3 part kit with aggregate or Liquid Only to add your own aggregate or NP1 can also be used as a primer.
Hot
PerfectPrimer Floating Floor Prep (formerly PerfectPaint) | Seal-Prime-Paint One Step | Asbestos Til...
From: $470.00- SEAL - PRIME - PAINT all in one step wide range of dangerous and difficult flooring materials: asbestos, lead, mastics, glue, cements without need for expensive removal
- Great bonding to smooth, non-porous surfaces found in commercial offices and homes including VCT, ceramic tile, vinyl, linoleum
- Safely encapsulate, rather than grind asbestos and lead prior to application of vinyl, tile, wood or other resilient flooring
- Reduce surface prep, expense and project completion time
- No need for scraping, grinding, solvents, soy gels, or removal of mastics
- Molecular adhesion ensures a strong bond to difficult non-porous surface
- Leaves a nice paint finish to your flooring project
- Water based Non-Toxic, no harmful VOCs
- Cleans up with water
Pigment Color For 5500 Polyaspartic Coating
$64.00- Pigment Designed to Color the 5500 Polyaspartic made by ASTC Polymers
- Add a Beautiful Decorative Color to Your 5500 Polyaspartic Project
- 7 Different Colors to Choose From!
- Sold in Quart Containers - Colors 2-3 Gallons When Mixed Into Clear 5500
Pigment For E344QC, E449 and E450SF Polyaspartic
From: $45.00- Pigment Designed to Color E344QC and E449SF Polyaspartic Coating
- Add a Beautiful Decorative Color to Your Polyaspartic Project
- 13 Different Colors to Choose From!
- Use 16 oz pigment per 3 gallon kit E344 QC and E449SF or 5-6 oz pigment per gallon
Plugger 10 Clear Masonry & Wood Acrylic Flat Sealer
From: $43.00- Flat Sheen Acrylic Water Sealer
- Clear, Will Not Yellow
- Protect With Little Change in Appearance
- 3 Year Warranty
- Water Base, Low VOC, Eco-Friendly
- Professional Grade
- Painted & Unpainted Concrete, Masonry, Wood
Plugger 25 Clear Masonry & Wood Acrylic Flat Sealer
From: $48.00- Flat Sheen Acrylic Water Sealer
- Clear, Will Not Yellow
- Protect With Little Change in Appearance
- 5 Year Warranty
- Water Base, Low VOC, Eco-Friendly
- Professional Grade
- Painted & Unpainted Concrete, Masonry, Wood
Polyurethane HD IsoFree Aliphatic 2K Floor Coating | High Gloss Satin Matte | Low Temp 40 °F
From: $64.00- UV Resistant Will Not Yellow
- Zero VOC- SCAQMD Compliant
- Choice of High Gloss, Satin or Matte Finish
- Clear & White Color
- Excellent Adhesion
- Outstanding Chemical Resistance
- MEK Double rub @50% solids Passed 2,000 Cycles Test
- For Concrete, Brick, Wood, Metal, Tile (glazed & unglazed)
Satin-Lok Wet Look High Gloss Acrylic Sealer
From: $58.00- High Gloss Wet Look Acrylic Water Sealer
- UV Resistant Will Not Yellow
- 5 Year Warranty
- Water Base, Low VOC, Eco-Friendly
- Professional Grade
- Painted & Unpainted Concrete, Masonry, Wood
UW601 Underwater Concrete Crack Filler Epoxy Paste Repair
$350.00- Make Repairs Underwater or on Wet Surfaces
- Concrete and Masonry
- Both Horizontal & Vertical Repairs
- Good for Cracks up to 1/8" and Thin Build Repairs
- Apply 35F - 90F
- 100% solids with 0 voc
- Low odor
UW602 Underwater Pourable Concrete Crack Filler Epoxy Repair
$325.00- Make Repairs Underwater or on Wet Surfaces
- Concrete, Cement and Masonry
- Both Horizontal & Vertical Repairs
- Good for Larger Cracks and Wide Variety of Repairs
- Easy to Use Pourable Formula
- 100% solids with 0 voc
- Low odor
Wet Look High Gloss Acrylic Sealer For Wood & Masonry
From: $44.00- High Gloss "Wet Look" Acrylic Sealer
- Beautiful Appearance
- Interior and Exterior Surfaces
- For Concrete, Masonry, Brick, Stone, Wood
- Breathable Coating
- UV Resistant Will Not Yellow and Eco-Friendly
Whiteboard Paint Dry Erase Water Based Polyurethane Coating
From: $60.99- Turns almost any surface into a Dry Erase Whiteboard
- Comes in Clear or White Color
- Write on it only 72 hours after application
- Tough, Durable, Long Lasting Dry Erase Surface
- Scratch Resistant
- Great Chemical and acid resistance
- MEK Double rub @50% solids Passed 2,000 Cycles Test
- Non-yellowing & UV resistant topcoat
- Odor Free and Zero VOC's
- Water Based and Non-Flammable
FREE SHIPPING
All US Ground orders in Lower 48 States by FedEx and USPS
WORLDWIDE DELIVERY
Shipping Ground, Air, Ocean. Call about our Special Export Programs
Copyright 2022 by Exterior Performance Coatings