Return to previous page
  • Overview
  • Specs
  • Coverage Rate
  • Application

Product Description

4100 ESD Anti-Static Restores Floor Gloss & Resistivity

ACL Staticide 4100 Restorer Cleaner renews static decay properties, surface resistivity and the durability of ACL floor finishes. Special conductive additives clean while simultaneously breaking down electrical discharge and returning floor finishes to safe specifications. No harmful chemicals like ammonia, phosphates, alkali, nonylphenol (NP), or nonylphenol ethoxylate (NPE) are used in the formulation. This special detergent can be applied with a mop or in a standard burnishing machine for easy application. Comes in a concentrate, 1 part 4100 to 10 parts water.

Neutral cleaners that are safe for most floor polishes can often harm ESD-safe finishes by introducing contaminants and abrasive ingredients. 4100 Restorer Cleaner will lift dirt and reestablish shine in problem areas that are prone to wear by heavy traffic. In addition, this unique concentrated formula break down electrical discharge, lower resistivity, and return floors to safe specifications.

Whether used as a spot-cleaner or as a detergent for full floor maintenance, including Restorer Cleaner as part of the Staticide® dissipative floor finish maintenance plan can save companies money by successfully prolonging cleaning and strip cycles.

Available as a concentrate, this cost-effective solution is suitable for mops, auto-scrubbers, and standard burnishing machines.

Where is 4100 used?

  • Electronics manufacturing and assembly, ESD protected areas electronic, medical, clean
    room manufacturing facilities

Why 4100 ESD Anti-Static Cleaner?

  • Lengthens maintenance cycle
  • Removes black heel marks
  • Revitalizes gloss
  • Surface resistivity: 107–109 ohms per square @100 volts
  • High solids concentrate
  • Dilution ratio 1:10 (1 part cleaner to 10 parts water)
  • Covers approximately 1,000 – 1,500 square feet per diluted gallon
  • Can be easily buffed
  • pH neutral
  • Low foam formulation
  • Zinc-free and no ammonia, phosphates, alkali, acids or formaldehyde
  • Non-toxic and biodegradeable
  • Low VOC <1%
  • Versatile application with mops, auto-scrubbers and standard burnishing machines

TECHNICAL INFORMATION

Surface Resistivity 107 – 109 ohms per square
VOC < 1%
Solids 25%
COVERAGE RATE SQUARE FEET/GALLON PER COAT
Average concrete surface 1500 – 2000

APPLICATION INSTRUCTIONS

Sweep floor with untreated, dry mop.  Dilute Restorer Cleaner 10:1 (10 parts water to 1 part concentrate).  Using a clean rayon mop, apply a thin coat of mixed solution to the floor by fully saturating mop and then wringing out excess cleaner so that the floor is not over saturated with moisture.  Remove soiled solution.  Allow floor to dry one hour before resuming traffic.

For auto scrubbers, gently scrub diluted solution with clean polishing pad (white).  Use 1,500 – 2,000 RPM with light pressure setting to prevent removal of finish.

Check resistivity and apply a second treatment if ncessary.  Consult floor finish application procedure for details and precise instructions.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

Reviews