E116 Rust Inhibitive Epoxy Primer

CURE TIME

Temperature                                         Tack Free                                       Minimum Recoat                    

90°F                                                   2 hours                                                  3-4 hours

75°F                                                   3 hours                                                  4-5 hours

50°F                                                   8 hours                                                18-24 hours

Time will be longer for films thicker than 4 mils.  When spraying, use a 50% overlapping crosshatch pattern to minimize the occurrence of pinholes.  Do not apply to surfaces below 45°F or above 120°F.  Do not apply over dew or frost.  Do not apply if the temperature is within 5° of the Dew Point.

MIXING AND APPLICATION INSTRUCTIONS

SURFACE PREPARATION

Remove all dirt, grease, oil, chemical contaminants, soil and any other foreign matter before abrasive blast cleaning. Prepare and paint only clean, dry surfaces in accordance with Steel Structures Painting Council (SSPC Or National Association of Corrosion Engineers (N.A.C.E.) specifications.

1. Steel (Non- Immersion)

• Steel: Remove oil, grease and other chemical contaminants by solvent wipe or steam cleaning. Abrasive blast to a “Commercial” (SSPC-SP6) or “near White (SSPC-SP10) metal finish
• Galvanized Steel/ Aluminum: Solvent clean per SSPC-SP1 or steam clean. Sweep blast to achieve a minimum 1 mil profile.
• Previously Painted Surfaces: Solvent clean per SSPC-SP1 and/or power wash. Remove loose existing paint by wire b rush or other hand tools. Feather edges. Make test application to check for compatibility.

MIXING INSTRUCTIONS

Stir each component to a uniform consistency, using a variable speed explosion proof drill with Jiffy Mixer. Make sure any pigment settled to the bottom is incorporated. Do not vary proportions. E116 Primer is prepared by mixing 1 part Base (Part A) to 1 part Hardener (Part B) with a Jiffy Mixer. Be sure material is thoroughly mixed together. Allow an induction or “sweat in” time for 30 minutes before using.

APPLICATION PROCEDURE

Airless Spray                           Graco                             Conventional Spray               DeVilbiss                                

Gun                                          Silver Plus                       Gun                                        MBC or JGA

Pump                                       Xtreme 33:1                    Fluid Tip                                  E

Tip Range                                 .015 – .021                      Air Cap                                   704 or 777

Hose                                        3/8 inch I.D                     Atomizing Pressure                  50-60 psi

Pressure                                   2300-2700 psi                 Fluid Pressure                         15-25 psi

Filter Size                                  60 Mesh                         Hose                                          3/8 inch ID

When spraying, using a 50% overlapping crosshatch pattern to minimize the occurrence of pinholes. Do not apply to surfaces below 45F or above 120F. Do not apply over dew or frost. The surface temperature should be at least 5F above the dew point.

Roller– Thin up to 10% by volume with SA-65 Reducer, depending on temperature. Use a 3/8″-1/2″ nap phenolic core, shed resistant roller cover. Roll in the same direction always keeping a wet edge. Do not over roll product.

Brush– Use pure bristle brush

For Safety reasons and to assist curing of the wet film, proper ventilation is necessary thorough application and cure. When using a pigmented Finish Coat, be sure the batch numbers are all the same to provide a uniform color.

Finish Coat, be sure the batch numbers are all the same to provide a uniform color.

V.O.C.

Unthinned                                Thinned 5%                                 Thinned 10%             

            2.82 lbs/gal                               3.02 lbs/gal                                  3.20 lbs/gal

(338 GMS/Liter)                           (362 GMS/Liter)                             (384 GMS/Liter)

CAUTIONS

E116 Epoxy is flammable.  Keep away from all sources of ignition during mixing, application and cure.  The HARDENER (Part B) and mixtures of BASE (Part A) with HARDENER (Part B) can cause eye and skin burns as well as allergic reactions.  The use of goggles, fresh air masks or NIOSH approved respirators, protective skin cream and protective clothing is a recommended standard practice when spraying coatings. This product is sold without warranty as to performance expressed or implied.  Users are urged to make their own tests to determine the suitability for their particular conditions.

SEE SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS. KEEP AWAY FROM CHILDREN. NOT FOR RESIDENTIAL USE. FOR PROFESSIONAL AND INDUSTRIAL USE ONLY.

SEE MATERIAL SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.  FOR PROFESSIONAL AND INDUSTRIAL USE ONLY  KEEP AWAY FROM CHILDREN.  NOT FOR RESIDENTIAL USE NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY HARM.