1007 Polyurea Coating Fast Set Waterproof Elastomeric Spray | Flexible 600%+ Elongation | 10-30 Second Set Time | 100% Solids

APPLICATION INSTRUCTIONS

Moisture Vapor Reduction

1007 should be applied to concrete surfaces as part of a “systems approach”. Use with CMW vapor barrier treatment for the concrete and the 7001 as the primer, pinholes are reduced.

Prime

Prime when needed using the 7001 primer.  The 1007 cross links with the 7001 primer and products excellent results when used together as a system.  . Prime 2 to 4 hours prior to the 1007 application for best results.  Spray the polyuria on the primer only after the primer has become tack free.

Note:  The best spray application results are obtained coating concrete when the ambient temperature is decreasing.  In applications where it is not possible to use the temperature to your advantage it is suggested that the CMW 8000 be used in conjunction with 7001 primer and the 1007 polyurea spray.

Preparation

Concrete must have a minimum 28 day cure prior to application. Remove any curing agent, form release materials, oils, wax, moisture or any material that may effect bonding. Clean and wash to remove contaminants and maintain pH 8.0-11.0. *

Perform a Moisture Vapor Test before making the coating application on concrete. Provide rough profile minimum 2 mils. Review ASTM D4259 Abrading Concrete and ASTM F1869 Measuring Moisture Vapor Emission. Seal/repair all bug-holes, cracks and spalls, see ASTC data sheets on 830, 4034 and 3004 (joints). Steel; Near white sand blast per SSPC-SP10/NACE 2. Welds, seams, edges, etc. grind/blast smooth and provide 2 mil profile. Immersion – review SSPC-SP1.

Application

Use only heated, high pressure spray equipment  & impingement gun. Maintain a fluid pressure minimum of 2,000 psi and minimum heat 160oF.  Substrate Surface temperature should be -20F to 120F. Apply at no less than 5F above dew point.   Apply at specified mil thickness over primer as required for the application.  Always preheat and mix Part B before use.  Avoid wet surfaces or exposure to moisture during application.

The 1007 polyurea coating is applied via high pressure heated spray equipment such as Arma Proportioners or Graco Reactor Series Polyurea Spray Pumps .

Spraying 1007 requires special equipment, user must be a professional applicator qualified in the use of high performance polyuria materials and specialty application equipment.

Finish

The finish of this product is best using a stipple surface with the 1007 over freshly applied 1007.

Color

Black, Medium Gray, Kaki Tan. Note: Aromatic systems will shift color from exposure to UV. Dark colors resists color change more then light colors.

Limitations

Do not use on wet surfaces or expose part A to moisture. Keep out of direct sunlight, store drum kits on wood pallets at room temperature. Always mix/agitate the part B before and while using using. Pre-heat drums as needed per environmental temperature. Best results over vapor barrier and/or compatible primer. Protect from cold during storage and shipping.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.