6009 Epoxy Concrete Floor Coating is 100% Solids | Low Temp 35F | 17 Colors | Quick Cure

Coverage rate for 6009 depends on how thick applied.  At 100% solids, nothing lost to evaporation after it dries (compare to 50% solids epoxy at big box stores which lose 1/2 of material in container to evaporation).  For garage floors recommended 10 mils minimum (160 sq’/gallon) epoxy basecoat thickness.  One 3 gallon kit of 6009 protects most 2 car garages, covering 480 sq’ at 10 mils thick in a one coat application (applied at 160 sq’/gallon).

APPLICATION INSTRUCTIONS

Preparation:

Concrete must have a minimum 28 day cure prior to application. Remove any curing agent, form release materials, oils, wax, moisture or any material that may effect bonding. *Perform a Moisture Vapor Test before making the coating application on concrete.  Can use the ASTC CMW 8000 to help reduce hydrostatic vapor pressure prior to application of the 6009.

Use a concrete (diamond) grinder or brush blast on the surface to provide rough profile minimum 2 mils (remove slick, smooth surface so concrete feels like a 100 grit sandpaper). Review ASTM D4259 Abrading Concrete and ASTM F1869 Measuring Moisture Vapor Emission. Seal/repair all bug-holes, cracks and spalls, see ASTC data sheets on 830, 4034 and 3004 (joints).   Do not apply 6009 to floors that have not been properly repaired, treated and primed as needed or that do not have a pH of 7-8.5.

Optional:  To reduce chance of concrete outgassing or enhance color saturation, recommend E5015 Water Based Epoxy comes in 20 colors to match topcoat.  For quick recoat, one day day project OR application in damp conditions recommend E155CL Epoxy Clear Primer with recoat in 30 min – 1-1/2 hour for 100% solids topcoats and application over damp or moist concrete.

Thinning: Xylene, use sparingly for desired application result. Test before using on a large area

1) PRODUCT STORAGE: Product Must Be Stored In An Area That Will Bring The Product To Room Temperature Prior To Using. Continuous Storage Should Be Between 60 And 90 Degree F on wood pallets. Keep From Freezing and Keep out of direct sunlight.

2) PRODUCT MIXING: READ CAREFULLY.  Improper Mixing May Result In Product Failure.  This Product Has a 2 To 1 Mix Ratio By Volume- Mix 2 parts by volume Of Part A With 1 part by volume Of Part B. ( Example: to mix 1 gallon total 6009 to get started, measure 2/3 gallon Part A and mix with 1/3 gallon Part B).  Do not change the proportions and recommend do not mix more than you can use in 15 minutes.

Improper mixing may result in product failure.

For best mixing results and proper blending of parts A and B, recommend a Jiffy Mixer style drill mixer.

Use of an improper drill mixer can result in streaking of the color because the pigment has not been thoroughly blended.  It can also create curing problems if the hardener also called activator (Part B) is not thoroughly blended with the resin (Part A) which can cause some areas on your floor to remain soft and not harden properly.  DO NOT USE A PAINT MIXER.  Many mixing problems described above can be traced back to using a paint mixer..  DO NOT HAND MIX as this approach can also result in the same problems as using a paint mixer.

****IMPORTANT NOTE AFTER MIXING:****

Once parts A&B are thoroughly mixed, immediately pour 100% of all mixed product on the floor in a ribbon pattern, S or W shape over the area you want that amount of product to cover. The risk of leaving product in the bucket is that it will become hard and reduce the working time by a minimum of 50% and may harden and start smoking in the bucket before you get back to it.

Mix part A (resin – color) separately in a container 4-6 minutes with a Jiffy Mixer first before combing parts A and B (hardener) together.  Clean mixing tool with solvent after mixing part A before mixing part B to prevent starting the chemical reaction and shortening cure time.  Only start mixing Parts A and B together when ready to start project.  Pour Part B into Part A while mixing at slow speed, 650 rpm until a uniform blend is evident and streak Free.  Avoid Whipping Air Into The Coating during mixing.  Mix completely for approximately one to two minutes.

Be sure to work the bottom and edges of the bucket to ensure the entire contents of each part are mixed. The colored veins need to disappear. If the two components are not mixed completely the epoxy will not cross-link well and can develop curing problems that will lead to a substandard coating.  In 6009 that is colored, improper mixing can result in uneven color when pigment is not fully blended.

It’s very important when mixing not to run the drill too fast or pump the mixing paddle up and down. Doing either of these this will introduce air into the mix which will be rolled into the coating and create air bubbles at the surface. The epoxy should have a nice even consistency without any color streaks.

Pour the 6009 out on the floor immediately after mixing and do not let the 6009 sit in the bucket.  Leaving it in the bucket for as little as a minute or two can shorten the pot life by half or more.

3) PRODUCT APPLICATION: This Product Can Be First Applied Using A Flat, Knotched, Or Serrated Squeegee, moving product around the surface for the desired coverage rate (thickness), Then Back Rolled to ensure proper adhesion with the surface.  (example:  Project calls for 1 gallon 6009 to cover 320 sq’ – then after mixing pour 1 gallon in a S pattern over a 16’x20′ area, squeegee so product covers entire surface area and then Use A 3/8” Nap Roller To Back Roll).  Can use A Chip Brush To Cut Out edges. Maintain Temperatures Within The Recommended Ranges During The Application And Curing Process. It Is Best To Maintain A Wet Edge To Avoid Roller Marks. Direct Sunlight Or High Temperatures May Cause Visible Roller Making During Application.

4) RECOAT OR TOPCOATING:  Although the 6009 recoat window is typically 4-5 hours at 75F, it Is Best To Test The Coating Before Recoating Or Topcoating. This Is Done By Pressing Your Thumb On The Coating To Ensure A Fingerprint Impression Is Not Visible. If There Is No Impression Visible, Then Coating The Floor Can Be Done. Note, Colder Temperatures Require Longer Cure Times Before Product Can Be Recoated. Note, colder or hotter than 75 degrees can affect the curing time schedule   Prior To Coating The Floor, Make Sure There Are No Contaminants Exist. If Contaminants Or A Blush Exists, Remove With A Standard Detergent Cleaner And Ensure Floor Is Clean And Dry Prior To Coating.

Going past the re-coat window, typically 24 hours depending on temperature and humidity, means the 6009 has become too hard and needs to be sanded with a 100 grit sanding tool to rough up the surface, wiped clean with acetone and then once the acetone has flashed off, you can apply the next coating.

5) CLEANUP/FLOOR CLEANING: Use Solvents For Cleanup. When Cleaning The Floor, CAUTION! Some Cleaners May Affect The Color Of The Installed Floor. Test Each Cleaner Used In A Small Area, Ensuring No Damage Occurs. Restrict The Use Of The Floor To Light Traffic And Non-Harsh Chemicals Until The Floor Is Fully Cured. Allow The Floor To Remain Completely Dry During The Curing Process.

7) RESTRICTIONS: Restrict The Use Of The Floor To Light Traffic And Non-Harsh Chemicals Until The Coating Is Fully Cured. It Is Best To Let The Floor Remain Dry For The Full Cure Cycle. Dependent On Actual Complete System Application, Surface May Be Slippery, Especially When Wet Or Contaminated; Keep Surface Clean And Dry.  Consider using an anti-slip additive in applications where floor can become wet.

LIMITATIONS:

• Concrete; Best results over 2 to 3 mil profile and vapor barrier as needed.
• Colors Or Gloss May Be Affected By High Humidity, Low Temperatures, Chemical Exposure, Or Exposure To Lighting Such As Sodium Vapor Lights.
• For Best Results Use A 3/8” Nap lint free professional grade epoxy Roller cover
• Strongly recommend using a Jiffy style mixer for proper blending of product
• Slab On Grade Requires Moisture Barrier
• Substrate Temperature Must Be 5°F Above Dew Point
• All New Concrete Must Be Cured For At Least 28 Days
• Physical Properties Are Typical Values And Not Specifications
• Tire Contact May Cause Staining Or Discoloration (Long Term Parked Vehicles)
• Colors May Vary From Batch To Batch, Therefore Use Only Product From The Same Batch For An Entire Job.
• Temperature conditions: 4 to 5 hour re-coat set time based on 75F temperature.6009 will set faster in hotter conditions and slower in colder conditions.
• Surface may be slippery when wet, recommend using an anti-slip additive in applications where floor can become wet.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

Check out a couple of our customers previous projects using the 6009!

3 Car Carage Epoxy Floor with 6009

Warehouse Floor Protected by 6009

Garage Turned Man Cave

Machine Shop Shines with 6009 Epoxy