Cold weather
Showing 1–12 of 36 results
-
10x Polyurea Interior Control Joint Filler | Quick Cure | Cold Temperature Apply Down To 0F
- Quick Back in Service
- Ideal for High Speed Application using Machine Dispensing System or for small projects easy application using twin cartridge kits and 300 ml x 300 ml cartridge kits
- High Shore Hardness for superior protection and support to joint edges
- Cold Application down to 0F
- Rapid curing
-
3003 Polyurea Slow Set Interior Control Joint Filler | Low Temp -20°F
- Offers load transfer across control joints for good protection of edges
- Back-in-Service "Drive-Over" in 30 to 60 minutes
- Longer working time than the 3004 Fast Set Polyurea
- 5-8 Minute Gel Time @ 77°F
- Meets USDA Requirements for incidental food contact
-
3004 Polyurea Fast Set Interior Control Joint Filler | Low Temp -20°F
- Quick Back-in-Service "Drive-Over" in only 20-30 minutes
- Offers load transfer across control joints for good protection of edges
- Ideal for High Speed Application using Machine Dispensing System or for small projects easy application using twin cartridge kits and 300 ml x 300 ml cartridge kits (total 21 oz or 600 ml per cartridge kit)
- Tack Free only 2-3 minutes
- Meets USDA Requirements for incidental food contact
-
5500 Polyaspartic Polyurea Coating Roll Down Low Temp 30°F | 87% Solid
- Beautiful Clear Appearance
- Quick recoat time in as little as 1 – 1.5 hours
- Waterproofing Elastomeric Systems
- Good In Submerged Service Projects Like Fountains
- Works well on concrete, brick, steel, wood, fiberglass
-
5500HS 100% Solids Polyaspartic Polyurea Coating Roll Down | Low Temp 30°F | Flexible 120% Elongation | 1:2 Mix Ratio | 1 Coat Coverage
- Beautiful Clear HIGH GLOSS Appearance
- 100% Solids For Thick 1 Coat Coverage Full Flake, Quartz, Silica Sand Systems to 16 mils DFT (100 sq'/gallon)
- Quick 24 hour back in-service (at 75F)
- Waterproofing Elastomeric Systems
- Good In Submerged Service Projects Like Fountains
-
5500M Matte Finish Polyaspartic Polyurea Coating Roll Down | Low Temp 30°F | 89% Solids | Flexible 120% Elongation
- Beautiful Clear MATTE FINISH Appearance
- Quick recoat time in as little as 1 – 1.5 hours and 24 hour back in-service (at 75F)
- Waterproofing Elastomeric Systems
- Good In Submerged Service Projects Like Fountains
- Outstanding Chemical Resistant
-
6007 Wet Condition Epoxy For Concrete & Steel | Low Temp 35°F | 100% Solids
- May be applied in damp and wet conditions where wash-down of areas is problematic
- Withstands up to 15-18 psi hydraulic vapor pressure
- Provides protective attractive color coat epoxy flooring system
- Excellent working properties
- Exceptional corrosion protection of both concrete and steel
-
6009 Epoxy Floor Coating Industrial & Commercial Low Temp 35°F | 100%
- Protective and attractive color coat epoxy flooring system
- Designed to seal floors against abrasion, water, oils and chemicals
- Good Color stability
- Wide application temperature range 35°F to 125°F (1.7°C to 52°C)
- Quick re-coat time 4-5 hours (at 75°F)
-
Aspartic 100 High Build Polyaspartic for Concrete Floors | Low Temp 30°F | 100% Solids
- Tough, durable topcoat for interior epoxy floor coatings Very low to no odor great for sensitive odor indoor projects Can be used as high build topcoat up to 16 mils or 100 sq'/gallon Cold temperature application down to 30°F Excellent chemical and abrasion resistance UV Stable and will not yellow Beautiful high gloss appearance Designed for high traffic and industrial areas 100% Solids Performance Available in clear & 14 colors!
-
Aspartic 85 Polyaspartic Quick Cure Concrete Floor Coating | Low Temp 30°F
- Tough, durable topcoat for interior epoxy floor coatings
- Cold temperature application down to 30°F
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
-
DT-454 Epoxy Quick Cure UV Concrete Floor Coating Low Temp 40F | 100% Solids
- Tough, Durable Epoxy Coating
- Quick cure 6-7 hour re-coat time
- Outstanding Bonding
- Good chemical, impact and abrasion resistance
- UV Resistance
-
E100 Urethane Primer Finish Coat | Aluminum Galvanized & Rusty Steel | Dry Heat to 400 °F | Apply Down to18°F | Quick Cure
- Prime over Steel, metal, weathered galvanized steel, aluminum, fiberglass, polyurethane foam and previously painted surfaces
- Fast recoat 1-2 hours at 75°F & 50% R.H
- Cures down to 18°F dry and apply to 140°F
- High heat resistance up to 400°F dry
- Single component, easy to use