E7075 Smooth Primer | 100% Acrylic Latex | Stain Blocking | Concrete Stucco Wood Metal Plywood

COVERAGE RATE  (depending on texture and porosity of surface)

Masonry 100 - 250 square feet per Gallon

Stucco: 150-200 Square Feet Per Gallon

Plywood: 200 Square Feet Per Gallon

APPLICATION TEMPERATURE: Do not apply when temperatures are below 50°F or expects to drop below 40°F within a 24 hour period. If fog or rain is expected within 24 hours, DO NOT APPLY.

APPLICATION INSTRUCTIONS FOLLOW THESE SIMPLE APPLICATION STEPS

Surface Preparation:

Cleaning and General Preparation: Loose or peeling coatings must be removed by sand or water blasting. All loose or defective concrete or masonry and any surface contaminates such as dirt, oils, mildew, chalk and efflorescence which may adversely affect product adhesion and performance must be removed.

Application Instructions:

MIX THOROUGHLY PRIOR TO USE. For best mixing results, recommend a Jiffy style drill mixer.

Application can be done with brush, roller or sprayer.  For roller application suggest a 1/2" nap roller cover.  When applying with a sprayer suggest using a .017 orifice spray tip in a 5-17 configuration.  For smaller projects can use a fine .013 orifice spray tip in a 4-13 configuration.

CAUTION: Do not apply when temperatures are below 50°F or expected to drop below 40°F within a 24 hour period or when fog or rain is anticipated.

Stucco: 

Roll or spray at a rate of 150 to 250 square feet per gallon.

Exterior Plywood (Including T1-11): 

A. Seal all edges of panels

B. T1-11 should be brushed primed along the grain. If sprayed, apply liberally and then back roll.

C. Coverage will be approximately 200 square feet per gallon.

Drying Time: 

Dries to touch in 30 minutes. Can be sanded in 2 hours.  At 70F and higher temperatures, this product can be recoated after 2 hours.

Stain Blocking:

7075 Primer reduces tannin bleed on most woods and will reduce nail head rust and some light water stains. Important: Water base products contain emulsifiers and coalescents, which continue to evaporate after the product is touch dry.  However, in stain blocking applications, additional curing time will be needed. Do not thin for stain blocking properties. Some stains may require 2 coats of primer.

Water Stains: 

7075 Primer contains “stain blocking pigments” and will block out most water stains with one or two coats. When covering stains, remove as much of the stain as possible with paint thinner or TSP solution.

Limitations: 

• Do not apply over mildew
• Not recommended for below grade (NOTE: Retaining walls, planter boxes etc. must be waterproofed on the backside with a below grade waterproofing type material prior to back filling).
• Not recommended for application to frost covered surfaces.
• Not recommended for application if rain is expected within 24 hours.
• Do not apply when temperatures are below 50°F or expects to drop below 40°F within a 24 hour period or when fog or rain is in the 24 hour forecast.

Efflorescence: 

Must be removed prior to application of the E6475 Primer.  Suggest using Restore-N-Prep  OR by washing with a 10% Muriatic Acid Solution.

Mildew:

Must be removed prior to application of the E6475 Primer.  Mildew is a fungus, brown, black, grey or white in color which will rapidly grow through any coating applied over it. A solution of 50% household bleach and 50% water will kill the mildew. Rinse thoroughly. See precautions on bleach label before using.

Glossy Surfaces: 

Remove gloss by sanding or with a chemical deglosser.

Clean Up: 

Clean tools and hands with warm soapy water and rinse thoroughly.

Maintenance:

E6475 is NOT intended to be an exposed surface film.

Safety, Health & Environmental Recommendations: 

Use appropriate personal protective equipment. Consult label or material safety data sheet available in the Document Library.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.