E64 Rain Shield Elastomeric | Flexible 400% Elongation | 100% Acrylic | Ceramic Sphere Technology | Masonry Stucco Wood Metal Concrete | 800+ Colors

COVERAGE RATE

90-100 Square Feet Per Gallon  at 18 Mils wet (8.28 dry) film thickness

APPLICATION TEMPERATURE: Do not apply when temperatures are below 50°F or expects to drop below 40°F within a 24 hour period. If fog or rain is expected within 24 hours, DO NOT APPLY.

APPLICATION INSTRUCTIONS FOLLOW THESE SIMPLE APPLICATION STEPS

Surface Preparation:

Cleaning and General Preparation: Loose or peeling coatings must be removed by high pressure water blasting or other appropriate means. Remove all loose or defective concrete or masonry and any surface contaminates such as dirt, oils, mildew, chalk and efflorescence which may adversely affect product adhesion and performance.

Priming:

All surfaces should be primed with Rain Shield #6475 Acrylic Exterior Primer which contains ceramic spheres and special

additives to insure maximum adhesion of the coating system. NOTE: Applied primer which as been exposed to dirt, dust, salt air,

or chemical environments must be washed down and re-primed before the top coat is applied.

Application Instructions:

MIX THOROUGHLY PRIOR TO USE. For best mixing results, recommend a Jiffy style drill mixer.

Application can be done with brush, roller or sprayer.  For roller application suggest a heavy duty 3/4" nap roller cover.  When applying with a sprayer suggest using a heavy duty conventional airless pump with Maximum Flow Rate (GPM) of at least 1 gallon per minute) using a .021 orifice spray tip in a 5-21 configuration.  After application with sprayer, suggest dry backroll (adding no new paint) using a 1/2" nap roller cover.

CAUTION: Do not apply when temperatures are below 50°F or expected to drop below 40°F within a 24 hour period or when fog or rain is anticipated.

Drying Time: 

Dries to touch in two hours, recoat overnight. Drying time will vary depending upon temperature, humidity and film thickness. Do not apply under visible wet conditions.

Limitations: 

Do not apply over mildew Not recommended for below grade (NOTE: Retaining walls, planter boxes etc. must be waterproofed on the backside with a below grade waterproofing type material prior to back filling). Not recommended for application to frost covered surfaces. Not recommended for application if rain is expected within 24 hours. Do not apply when temperatures are below 50°F or expects to drop below 40°F within a 24 hour period or when fog or rain is in the 24 hour forecast.

Joint and Large Crack Treatment: 

Perimeter joints between unlike materials such as around doors, windows, vents, etc. and active joints such as curtain wall joints, expansion and control joints must be caulked and filled with an authorized elastomeric caulk carefully following the manufacturer’s

specifications.

Efflorescence: 

Must be removed by using Restore-N-Prep  OR by washing with a 10% Muriatic Acid Solution.

Mildew:

Mildew is a fungus, brown, black, grey or white in color which will rapidly grow through any coating applied over it. A solution of

50% household bleach and 50% water will kill the mildew. Rinse thoroughly. See precautions on bleach label before using.

Clean Up: 

Clean tools and hands with warm soapy water and rinse thoroughly.

Thinning: 

SPRAY APPLICATION: DO NOT THIN!!!

Maintenance:

Rain Shield systems are designed to be waterproof and can be water blasted to remove any dirt that may have accumulated on the surface over several years. Stubborn stains can be brushed to loosen the dirt before washing.

Safety, Health & Environmental Recommendations: 

Use appropriate personal protective equipment. Consult label or material safety data sheet available in the Document Library.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.