E211 Epoxy Primer & Sealer

Shelf LifeMinimum of 12 Months

                                                                                RECOAT TIME

                                                                                                    MINIMUM                              MAXIMUM

       TEMPERATURE                       TACK FREE                            RECOAT                              RECOAT

90°F                                   1-2 hours                              3-4 hours                                 3 days

75°F                                    2-3 hours                              4-6 hours                                 7 days

50°F                                  8-10 hours                             24-36 hours                           10 days

Times will be longer for films thicker than 3 mils.   For safety and proper product curing, good ventilation is necessary when painting indoors or in confined areas.  Be sure the batch numbers are all the same to provide uniform color.  Epoxy coatings may yellow or darken during application and after final cure.  This will affect the color but will have no effect on the performance of the product.  Heaters that emit carbon dioxide and carbon monoxide can cause the coating to yellow.

MIXING AND APPLICATION INSTRUCTIONS

SURFACE PREPARATION

Concrete: Remove all laitance, efflorescence, chemical containments, grease, oil, old paint and other foreign matter. The prepared surface must be clean, dry and structurally sound. Diamond grinding or water blasting may be necessary to achieve the proper profile. Acid etch or other chemical treatments should be evaluated.  Consult us for details of specific tests pertaining to acceptable pH and surface porosity. In all cases of surface preparation, the ph should be checked. A water dissipation test and a vapor barrier test should be run. Do not apply to slabs on grade unless a heavy unruptured vapor barrier has been installed under the slab.

MIXING INSTRUCTIONS

E211 is prepared by mixing 1 part Base (Part A) to 1 part Hardener (Part B) with an explosion proof variable speed drill and Jiffy mixer. Allow an induction time of 15 minutes before using. E211 may be thinned up to 10% with SA-50. Overthinning reduces the high film build capability.

Roller – Use a 3/8″ -1/2″ short nap phenolic core, shed resistant roller cover. Roll in the same direction always keeping a wet edge. Do not over roll product.

Brush– Use pure bristle brush

When spraying, use a 50% overlapping crosshatch pattern to minimize the occurence of pinholes. Do not apply to surfaces below 50F or above 95F. Do not apply over dew or frost. Do not apply if the temperature is within 5° of the Dew Point.

CAUTIONS

E211 is Flammable.  Keep away from all sources of ignition during mixing, application and cure.  The Hardener and Base can cause eye and skin burns as well as allergic reactions.  Use goggles, fresh air masks or NIOSH approved respirators, protective skin cream and protective clothing.  This product is sold without warranty as to performance expressed or implied.  Users are urged to make their own tests to determine the suitability for their particular conditions.

SEE SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS. KEEP AWAY FROM CHILDREN. NOT FOR RESIDENTIAL USE. FOR PROFESSIONAL AND INDUSTRIAL USE ONLY.

SEE MATERIAL SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.  FOR PROFESSIONAL AND INDUSTRIAL USE ONLY  KEEP AWAY FROM CHILDREN.  NOT FOR RESIDENTIAL USE NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY HARM.