E100 Moisture Cured Urethane Aluminum & Steel Primer Finish Coat | Dry Heat to 400 °F

CURE SCHEDULE

APPLICATION TEMPERATURE: 38ºF – 140ºF with relative humidity below 90%

E100 is a Fast Cure product for cold weather applying to surfaces down to 38° (needs to remain at this temp or above for at least 1 hour) and then during curing process temperatures further dropping ok to as low as 18°F.

MIXING AND APPLICATION INSTRUCTIONS

SURFACE PREPARATION Steel For best results, sand blast to a SSPC-SP6 “commercial” blast finish.  Where blasting is not appropriate, remove all loose rust and mill scale by power wire brushing or hand tool cleaning.  A tightly adherent rusty surface is acceptable.

Galvanized Steel – Aluminum

• New – Brush blast per SSPC-SP7 before applying E100.
• Old, Weathered, or Rusty – Remove all oil, grease, dirt, and other foreign matter.  Surface should be reasonably clean, dry, and free of contaminants.  Remove all loose rust, etc., as outlined above under steel

Previously Painted Surfaces Remove all loose, peeling, or blistered paint, and any other surface contaminants.  Make sure surface is sound and dry.  Apply a test patch of E100 over existing coating to insure good adhesion.

MIXING INSTRUCTIONS E100 is made ready for use by stirring so that the aluminum pigment is thoroughly dispersed in the resin and a uniform “silver” color is achieved.  Do not use a paint shaker.  When used over a period of time, stir occasionally to maintain uniform mix.  Thinning is not usually necessary.  If needed, use up to 10% SA-50 Urethane Reducer which is a water free grade (100% Xylene).  Always keep partially used containers tightly sealed to prevent air moisture from reacting with the material and forming a tough skin.   Skin can be removed and remaining material used.

For best mixing results and proper blending of parts A and B, recommend a Jiffy Mixer style drill mixer.

Use of an improper drill mixer can result in curing problems if the hardener also called activator (Part B) is not thoroughly blended with the resin (Part A) which can cause some areas on your floor to remain soft and not harden properly.  DO NOT USE A PAINT MIXER.  Most mixing problems described above can be traced back to using a paint mixer..  DO NOT HAND MIX as this approach can result in the same problems as using a paint mixer.

NOTE:  Always wear protective gloves and clothing while mixing and applying E100.  Do not get on skin.  E100 is difficult to remove.

APPLICATION PROCEDURE  E100 may be applied by brush, roll, or spray.  For rolling, use a ¼” – 3/8” shed resistant phenolic core cover.  When brushing, use a bristle brush.  For spray it is important that a moisture/oil trap be used on incoming air and that fluid lines be flushed first with an anhydrous solvent (water free) such as S-74.  Also, flush every 1-2 hours during use to keep lines clean from material build up.  Required equipment is as follows:

1. Airless Spray – Use a minimum 20:1 ratio pump with 80-100 psi inbound air. Recommend a .013” – .017:” tip.   Adjust pressure for proper atomization based on selected tip.

2. Convention Spray – Use a dual regulated pot with 15-25 psi fluid pressure and 40-50 psi atomization pressure.  A Binks #18 with a tip/air cap is recommended.

When spraying, use a 50% overlapping crosshatch pattern to minimize the occurrence of pinholes.  Do not apply to surfaces below 18°F or above 140°F.  Do not apply over dew or frost.  The surface should be dry and at least 5°F above the dew point.

RECOAT TIME Based on temperature of 75°F and 50% R.H. (relative humidity), E100 is tack free in 1-2 hours and may be overcoated in 2-3 hours.  Always check for fingernail hardness.  For maximum adhesion, recoat no longer than 6 hours at 75°F and 50% R.H.  High temperatures and humidity will shorten recoat time.  E100 must be top coated as soon as E100 has dried.  If E100 gets rained on or has condensation form on its surface, a sweep blast is necessary to abrade the surface before applying a topcoat.

CAUTIONS E100 is flammable.  Keep away from all sources of ignition during mixing application and cure.  Contains aromatic polyisocyanates.  Proper ventilation is necessary when painting indoors or confined areas.  Vapors and spray mist may cause eye/skin irritation as well as allergic reactions.  Always wear protective clothing, goggles, impervious groves and use NIOSH approved respirators.   For industrial use only.  Keep out of reach of children.  This product is sold without warranty as to performance expressed or implied.  Users are urged to make their own tests to determine the suitability for their particular conditions.

LIMITATIONS:

• Do not apply over frost, wet or damp surfaces or extremely high humidity conditions.
• Not recommended as tank lining for constant immersion.
• Must be recoated the same day.
• Partially used containers must be reclosed tightly to prevent moisture in air from reacting with material and forming a tough skin.  Skin can be removed and remaining material used.  Be sure to stir.

SEE MATERIAL SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.  FOR PROFESSIONAL AND INDUSTRIAL USE ONLY  KEEP AWAY FROM CHILDREN.  NOT FOR RESIDENTIAL USE NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY

We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications.

NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT.

We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products.

Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY HARM.