PaintPlus | Epoxy-Like Toughness | Hard Wearing | Water Based | PerfectPrimer Topcoat | Easy to Use

1 Coat Application: 275-325 Square Feet Per Gallon

2 Coat Application: 175-200 Square Feet Per Gallon (2 coats recommended if project will have heavier traffic)

APPLICATION INSTRUCTIONS

SURFACE PREPARATION: All surfaces must be dry, clean, free of chalk and loose paint, grease, oil, wax, silicone, efflorescence etc. Asphalt and previously painted concrete must be scrubbed with PerfectCleaner according to label directions, or a strong detergent such as TSP. Rinse thoroughly with clean water and allow to stand until completely dry. New and/or unpainted concrete must be primed when required due to asbestos contamination with PerfectPrimer first.  Surface should be roughed up or “etched” with a 25% solution of muriatic acid to water. Apply solution to concrete and allow to stand until bubbling ceases, rinse THOROUGHLY with clean water and allow to stand until completely dry. Wear proper eye, skin, and respiratory protection.

PRODUCT MIXING: For best mixing results recommend a Jiffy Mixer style drill mixer.

APPLICATION: Stir well to a smooth consistency immediately before use. Apply with a high 3/8″ or 1.2″ quality medium nap synthetic roller cover and a Nylon or Polyester brush.

UNPAINTED CONCRETE: First coat MUST be thinned with 1 pint of clean water per gallon of paint and brushed or rolled well into surface. Dries to touch in one hour, second coat may be applied after 12 hours dry time.

ASPHALT AND PREVIOUSLY PAINTED CONCRETE: Apply 2 coats allowing 12 hours between coats. For added slip prevention, up to one pound of clean and dry fine silica sand may be added to each gallon of paint. For best service, add sand in first coat material only. Stir occasionally during application to prevent settling of sand. Will take foot traffic in two hours, however, seven days curing time MUST elapse prior to automobile traffic exposure.

Do not apply PaintPlus over the following surfaces or coatings: Hydraulic cement, silicone or silicate sealers, epoxies, polyurethanes, and some glossy paints. To determine whether proper adhesion is possible, apply a small test patch of Sure-Grip to an inconspicuous area of the substrate in question and allow to dry 48 hours. Check adhesion by applying and then removing a piece of duct tape from the test patch. If any paint remains on the duct tape, the surface is not suitable for coating.

CLEANUP: Clean all hands and tools with soap and warm water immediately after use. Clean spatters immediately with warm soapy water. If spatters are allowed to dry, clean with xylene, lacquer thinner, or other strong solvent (read cautions and instructions on solvent label). CAUTION, some solvents may dissolve asphalt

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.