E591 100% Solids Wet Surface Epoxy Coating | Low Temp 35F

CURE SCHEDULE

APPLICATION TEMPERATURE: 40ºF – 120ºF  (40°F for steel and 50°F for concrete – with ability to cure down to 35°F only after at least 1-2 hours after application) with relative humidity below 90% Times may be longer for thickness above 5 dry mils. For safety and proper product curing, good ventilation is necessary when painting indoors or in confined areas.

Be sure the batch numbers are all the same to provide uniform color. Epoxy coatings may yellow or darken during application and after final cure. This will affect the color but will have no effect on the performance of the product. Heaters that emit carbon dioxide and carbon monoxide can cause the coating to yellow.

For maximum Interior gloss and color retention, apply 1 coat of E270 Polyester Epoxy. For maximum exterior gloss and color retention apply a topcoat of E370 polyurethane.

CHEMICAL RESISTANCE, SPLASH

MIXING AND APPLICATION INSTRUCTIONS

SURFACE PREPARATION Best method is a near white abrasive blast (SSPC-SP10) but E591 will perform well over minimally prepared surfaces depending on service requirements. Because of the lack of “standards” for minimal surface preparation, test applications should be made to determine adequate surface cleanliness and compatibility with existing paint.

Steel: Remove oil, grease and other chemical contaminants by solvent wipe or steam cleaning. Abrasive blast to a “Commercial” (SSPC-SP6) or “Near White” (SSPC-SP10) metal finish.

Galvanized Steel/Aluminum: Solvent clean per SSPC-SP1 or steam clean. Sweep blast to achieve a minimum 1 mil profile.

Previously Painted Surfaces: Solvent clean per SSPC-SP1 and/or power wash. Remove loose existing paint by wire brush or other hand tools. Feather edges. Make test application to check for compatibility.

Concrete: All new concrete must be cured at least 28 days. For on-grade concrete slabs, check that a moisture barrier film has been used. Testing may be necessary. Check for the presence of hardeners or residual forming membrane curing agents. Repair all cracks, bug holes, spalled concrete, voids and expansion joints

MIXING INSTRUCTIONS Stir each component to a uniform consistency with a variable speed drill with a Jiffy mixer. Then mix 3 parts Base A with 1 part Hardener B for 3 minutes. E591 may be reduced up to 20% with S-74 Reducer (or 100% MEK Solvent) per mixed gallon. Do not substitute reducers Improper mixing may result in product failure.

For best mixing results and proper blending of parts A and B, recommend a Jiffy Mixer style drill mixer.

NOTE:  Always wear protective gloves and clothing while mixing and applying E591.  Do not get on skin.

APPLICATION PROCEDURE FOR SPRAY APPLICATION (Airless or Conventional)

• When spraying, use a 50% overlapping crosshatch pattern to minimize the occurrence of pinholes. Do not apply to surfaces below 40°F or above 120°F. Do not apply over dew or frost. The surface temperature should be at least 5° above the Dew Point.

Roller – use a medium nap solvent resistant phenolic core roller.

Brush – use a pure bristle brush * Gloss will exhibit slight variation in brush or rolled film due to orientation of fillers. This does not affect product performance. For safety and proper product curing, good ventilation is necessary when painting indoors or in confined areas. Be sure the batch numbers are all the same to provide uniform color. Epoxy coatings may yellow or darken during application and after final cure. This will affect the color but will have no effect on the performance of the product. Heaters that emit carbon dioxide and carbon monoxide can cause the coating to yellow

CAUTION E591 Base is combustible. Keep away from all sources of ignition during mixing, application and cure. E591 Hardener (Part B) is corrosive and can cause eye and skin irritation as well as allergic reactions. The use of goggles, fresh air masks or NIOSH approved respirators, protective skin cream and protective clothing is a recommended standard practice when spraying coatings. Proper ventilation is always required. This product is sold without warranty as to performance expressed or implied. Users are urged to make their own tests to determine the suitability for their particular conditions.

LIMITATIONS:

• Do not apply over frost surfaces or extremely high humidity conditions.
• Do not apply over expansion joints.
• Do not apply if the surface temperature is within 5° of the dew point.
• Always apply a test patch of E591 for owners approval prior to application
• Partially used containers must be reclosed tightly to prevent moisture in air from reacting with material and forming a tough skin.  Skin can be removed and remaining material used.  Be sure to stir.

SEE MATERIAL SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.  FOR PROFESSIONAL AND INDUSTRIAL USE ONLY  KEEP AWAY FROM CHILDREN.  NOT FOR RESIDENTIAL USE NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY HARM.