E28 Cool Life Deck Coating | Infrared Heat Reflective Technology in 12 Colors | 100% Acrylic | Concrete Wood Masonry Metal | Chemical Resistant

COVERAGE RATE

Coverage will vary depending on the surface applied to.

Smooth Surfaces: Up to 400 Square Feet Per Gallon

Rough Surfaces: 100-300 Square Feet Per Gallon

APPLICATION TEMPERATURE: No recommended for application when the temperature is below 55°F. Rain may damage uncured products. If inclement weather threatens, cover the deck to protect new application. Do not allow any non-applied product to freeze.

Type	Acrylic Resin
Viscosity	90-95 KU’s at 77°F
Solids	46-49% by Weight 34-37% by Volume
Diluent	Water
Flash Point	>200°F
VOC	Coatings: 1.03 g/L Material: 0.35 g/L

APPLICATION INSTRUCTIONS FOLLOW THESE SIMPLE APPLICATION STEPS

Surface Preparation:

Concrete, concrete decks, floors and walk ways New concrete must age for a minimum of 30 days. Cool temperatures and high humidity may require a longer cure time.

Remove all grease, oil and wax with T. S. P. Solution. (One pound of T. S. P. to 1 gallon of water.) Scrub with stiff broom until surface is thoroughly clean. Rinse thoroughly with clear water. Power wash all concrete with 3000 lb. pressure washer, spray tip should be no further than 6” from concrete surface. A properly etched concrete surface should resemble the texture of fine or medium sandpaper. Let dry thoroughly before applying coating.

For Interior and/or Hard Troweled Cement:

MECHANICAL ETCHING METHOD: Use a grinder or bead blaster with a dust filter, or vacuum attachment, evenly over the surface. A small hand grinder may need to be used where horizontal meets vertical substrates. Rinse thoroughly using a pressure washer to remove all remaining dust and residue. A properly etched concrete surface should resemble the texture of fine or medium sandpaper. Let dry thoroughly before applying coating.

Mildew: DO NOT PAINT OVER MILDEW. Mildew is a fungus, brown, black, grey or even white in color, and will rapidly grow through any coating applied over it. A solution of 50% household bleach and 50% water will kill the mildew. Rinse thoroughly. See precautions on bleach label for handling before using.

Glossy Surfaces: Roughen gloss by sanding; then wash with a T.S.P. solution and rinse thoroughly with water.

Previously Painted Surfaces: Clean all surfaces and roughen all glossy surfaces by sanding. Clean all surfaces thoroughly with a T.S.P solution and then rinse thoroughly with water. Do not paint over loose or peeling paint.

Unpainted Surfaces: For maximum durability, prime all surfaces to be coated. Caulk all cracks and nail holes.

Wood: Clean and primer all new wood with E1575 Primer. Coat with 1-2 thin coats of E28 Series.
Metal: Clean and etch all new metal. Prime all bare metal with E1575 or E7075 primer.

Weather: Do not install any product if the temperature is below 550. Rain may damage uncured products. If inclement weather threatens, cover deck to protect new application. Do not allow any non-applied product to FREEZE.

Priming: For best results and when necessary as specified, prime surfaces with this product (28 Series) thinned with one quart of water before applying the top coat.

Application:

Box and mix all containers to insure consistent color. Neatly cut-in all edges with a brush and roll the main area using a 1/2” to 3/4” nap, good quality roller cover. Be sure to spread evenly in a “V” pattern, rolling in both directions. It is best not to apply this product in the direct sun at temperatures above 80°F. Thinning slightly with water and applying thin coats will help avoid streaks when working in direct sun. (See specifications for more application details).

Dry Time: Allow six (6) hours between coats and light foot traffic.  Allow forty-eight (48) hours before placing heavy objects on the surface. Cool temperatures and high humidity may require a longer cure time.

Maintenance:  See the E28 Maintenance Sheet in the Document Library

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.