Return to previous page
  • Overview
  • Specs
  • Coverage Rate

Clear-Seal 100% Urethane High Gloss Super Premium Sealer

Rainguard Clear-Seal™ 100% Urethane is an exceptionally tough, durable and breathable low gloss sealer.  This product creates a hard glossy film that is more UV resistant, stain resistant, and hot tire resistant than that of Clear-Seal™ acrylic urethane blended sealer.  It provides a nice looking high gloss finish for concrete, stone, masonry, unglazed tile and wood surfaces.  It is a water based, low VOC, single-component, self cross-linking clear urethane water based sealer.

Clear-seal is available in both a High Gloss and Low Gloss formula in 1 gallon and 5 gallon containers. For optimal results, add Urethane Quick Cure Performance Additive (select this option under the Performance Additive dropdown).

Clear-Seal is designed to increase chemical resistance, impact resistance, chip resistance, added UV protection and better absorption of the Clear-Seal.  Urethane Quick Cure Performance Additive mixes easily.  Add 2 oz of Urethane Quick Cure per gallon of Clear-Seal™ 100% Urethane. Mix for 5-10 minutes. Adding Urethane Quick Cure gives the solution a 72-hour pot life. Extend pot life by adding more Urethane Quick Cure if needed.

Where is Clear-seal High Gloss used?

  • Construction & Remodel Projects:   Commercial floors subject to heavy foot traffic, walkways, protection of outdoor and indoor painted wall murals
  • Homeowner projects:  Driveways, garage floors, decks, patios, porches, walkways, fences

Why Clear-Seal High Gloss Sealer?

  • Excellent Impact and wear resistant
  • Resists hot tire pick-up for vehicular applications
  • Performance Additive Available for Even Better Performance
  • Excellent Chemical and Stain Resistance
  • Resists UV rays – won’t yellow
  • Excellent adhesion
  • UV protectant
  • Anti-Slip Finish Available
  • Interior/Exterior Protection for Concrete, Brick, Pavers, Stone and Wood
  • Specified by architects in CSI Division:  099123, 099723, 099313

TECHNICAL INFORMATION

Color Clear
Sheen/Gloss Level High gloss
Re-Coat Time When completely dry, 4-6 hours typical.  Do not wait longer than 24 hours before applying a 2nd coat.  If you do, sand surface with 100-150 grit sandpaper, remove debris, wipe with acetone just before application
#Coats Recommended 1 – 2 coats depending on level of protection desired
Back in-service time 24 hours to walk-on and 72 hours to drive-on
Application method Spray, brush or roll (1/4″-3/8″ nap non-shed, water resistant) application.  Sprayer requires use of heavy-duty acetone pump sprayer (ie; Chapin Xtreme) or pesticide sprayer (ie Hudson, Ortho) with low volume fan tip
Where Can it be Used All Interior|Exterior architectural surfaces
Apply to New Concrete 28 days
Application Temperature 50F|10C t0 90F|32C Surface & Air temperature
 Base  Water
VOC Content <50 g/L
Use on Material All masonry, concrete, paver, stone, unglazed tile and wood surfaces
Odor Slight Latex Smell
Viscosity @77F (Brookfield) 50-100 cps
Direct Impact 140 inch-lbs
Reverse Impact 40 inch-lbs
Pencil Hardness 2H
Taber Abrasion, CS 17 Wheel, 5 to 7 Days 8.4 mg loss

CHEMICAL TEST DATA
IPA No Effect
MEK No Effect
Toluene No Effect
50% Sodium Hydroxide No Effect
50% Phosphoric Acid No Effect
50% Sulfuric Acid Stain Only
37% Hydrochloric Acid Stain Only
100% Acetic Acid Failure
COVERAGE RATE SQUARE FEET/GALLON
Porous Surfaces 250-300
Dense Surfaces 300-350
*Textured surfaces Decreases coverage rates

Reviews