AcrylicPoly DTM² Acrylic Modified Polyurethane WaterProofer & Primer | Flexible | Metal Concrete Masonry Wood Plastic | Non-Yellowing

COVERAGE RATE

The coverage depends on the surface. Test the product on a small area of the substrate to estimate coverage. Extremely porous surfaces may require multiple coats.

The use of fluted, scored block, raked joints, sandblasted or etched surfaces will result in greater absorption and lower coverage rates, by up to 40%. Test these areas for the expected coverage rate before general application. Allow for this increased surface area when determining material requirements.

APPLICATION INSTRUCTIONS

Surface Preparation

Prior to application, all surfaces shall be clean and dry with no oils, dirt, debris, or minerals such as efflorescence, lime and calcium. These stains, along with others, will prevent proper penetration of AcrylicPoly DTM2 to sufficiently seal.

The use of Restore-N-Prep™ Concrete and Masonry Cleaner system is recommended as a pretreatment to clean masonry surfaces. Once clean, allow the surface to fully dry before sealing or applying a topcoat (See the Restore-N-Prep™ TDS for details)

Mixing Instructions

Stir for 2-3 minutes with a jiffy blade at slow speed (500 RPM) to fully disperse the product.

Application Instructions

When using an airless sprayer, suggest using a fine tip, 4-13 to 4-14 (.013 to .014 orifice) spray tip size

Smooth Surfaces

AcrylicPoly DTM2 may be applied directly over most surfaces without primer. Apply a light coat at a thickness of 3 to 4 wet mils.

Porous Surfaces

Most porous surfaces should have a sealer or filler to adequately eliminate potential pinholes before applying AcrylicPoly DTM2.

1. Apply one coat of AcrylicPoly DTM2 (3 – 4 mils wet per coat). Allow 4 hours between coats or when coating is tack free.
2. Any runs should be brushed or rolled out immediately before drying.
3. When dry, thickness should be 1.5-2 mils* *For heavy duty applications such as warehouse floors with heavy forklift traffic, DFT thickness should be 3-4 mils.

Dry Time: 45 minutes – 1 hour at 75°F Thinning is recommended to avoid lap marks and allow for proper self-leveling characteristics. Use clean water only.

IMPORTANT: Proper methods to protect from over spraying should be implemented. Atomized particles will adhere to most surfaces and are extremely difficult to remove. Temperature and humidity directly affect dry time. Conditions should be between 40 – 95 °F (5 – 35 °C) and humidity should not exceed 80%.

Re-Application

Apply a second coat within 48-hours for proper adhesion. If the first coat has dried longer than 48-hours, abrade the surface to promote adhesion of the second coat.

Safe Handling

Use product only with adequate ventilation and/or an appropriate cartridge type respirator. Avoid contact with skin and wear protective gloves. Read the Safety Data Sheet before using.

Precautions

For horizontal applications it is the responsibility of the contractor to use appropriate non-slip additive depending on the project conditions. Use material in a well-ventilated area. Protect the work of other trades. Protect shrubbery and other plants with drop cloths. Protect automobiles and all other areas not to be coated from overspray. Remove overspray from any windows, automobiles, metal, etc. as soon as possible should it occur. To prevent permanent staining, clean spills or leaks in a timely manner.

All surfaces to be coated should be clean of any dirt and grime, efflorescence, lime run, form oils and release agents, grease, mud, excess mortar, and mold and mildew, etc. All cracks should be pointed or caulked. All voids, beeholes, masonry surface defects and openings such as conduits, pipes, drains, door frames, vents, air conditioner openings, electrical openings, control joints, or any dissimilar materials should be repaired using urethane or other approved patching.

Do not apply to surfaces if moisture content is greater than 25% as measured with an electronic moisture meter. Do not apply materials in climates where freezing temperatures have existed prior to application. Allow adequate time for surfaces to thaw. Establish that air, surface, and material temperatures are above 40°F (4.4°C) and at least 5°F above the dew point prior to painting.

Do not apply at temperatures below 40°F when temperatures are expected to drop below 40°F within 48 hours of application. Do not apply if rain, snow, or lower temperatures are expected within 48 hours. Do not apply if relative humidity is greater than 90%.

Store materials in a well-protected area at 45°- 90°F. Avoid freezing temperatures, direct sunlight, & moisture. Keep away from heat sources.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.