Rubber-Lok Liquid Synthetic Rubber | Ultra Flexible 1000% Elongation | Stops Leaks | Low VOC | UV Resistant | Concrete Stucco Masonry Wood Metal Asphalt Bitumin

COVERAGE RATE

Spread rates can vary depending on application needs. Below-Grade Applications would require 80-mils DFT. Above-Grade Applications require 40-mils DFT

APPLICATION INSTRUCTIONS FOLLOW THESE SIMPLE APPLICATION STEPS

Surface Preparation

Clean substrate from any contaminants that could prevent adhesion, including but not limited to oil, grease, dust, and debris. Solvents and commercial cleaners should not leave a residue per SSPC-SP1.

The use of Restore-N-Prep™ Concrete and Masonry Cleaner system is recommended as a pre-treatment to clean masonry surfaces. Once clean, allow the surface to fully dry before sealing or applying a top-coat (See the Restore-N-Prep™ TDS for details)

Application

Remove all contaminants and loose material, such as dust, dirt, oil, silicone, release agents, wax, mildew, salt deposits, heavy oxidation, and chalky or loose coating. Check the entire surface and thoroughly power wash it. Do not apply at temperatures below 45°F nor during, nor 24 hours preceding inclement weather, including rain, fog, mist, or freezing temperatures. PROTECT FROM FREEZING DURING SHIPMENT AND STORAGE. Do not store material at temperatures below 50°F. Flush all equipment with water before use. Stir Rubber-Lok thoroughly until uniformly blended but avoid excessive mixing to prevent air entrapment.

Safe Handling

Use product only with adequate ventilation and/or an appropriate cartridge type respirator. Avoid contact with skin and wear protective gloves. Read the Safety Data Sheet before using.

Clean Up

Clean up promptly by washing with acetone or recommended clean up solvent before product cures Once cured, product can only be removed from equipment mechanically. Cured product can only be removed mechanically. Dispose of according to local, state, and federal requirements.

Spread Rates

Spread rates can vary depending on application needs. Below-Grade applications would require 80-mils Dry-Film Thickness (DFT). Above-Grade applications would only require 40-mil Dry-Film Thickness (DFT).

Precautions

This is a high gloss finish and can be slippery when wet. Use material in a well-ventilated area. Protect the work of other trades. Protect shrubbery and other plants with drop cloths. Protect automobiles and all other areas not to be coated from overspray. Remove overspray from any windows, automobiles, metal, etc. as soon as possible should it occur. To prevent permanent staining, clean spills or leaks in a timely manner.

All surfaces to be coated should be clean of any dirt and grime, efflorescence, lime run, form oils and release agents, grease, mud, excess mortar, and mold and mildew, etc. If an acid etch or an acid stain has been applied to the surface, it must be thoroughly flushed to remove all residue and then allowed to dry completely.

Do not apply to surfaces if moisture content is greater than 25% as measured with an electronic moisture meter. Do not apply materials in climates where freezing temperatures have existed prior to application. Allow adequate time for surfaces to thaw. Establish that air, surface, and material temperatures are above 50°F (4.4°C) and at least 5°F above the dew point prior to painting. Do not apply at temperatures below 50°F when temperatures are expected to drop below 50°F within 48 hours of application. Do not apply if rain, snow, or lower temperatures are expected within 48 hours. Do not apply if relative humidity is greater than 90%.

Store materials in a well-protected area at 45°- 90°F. Avoid freezing temperatures, direct sunlight, & moisture. Keep away from heat sources.

California Prop 65

WARNING: This product can expose you to chemicals including bitumen (asphalt), which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.