Micro-Seal With Graffiti Control & Water Repellent For Porous Wall Surfaces

HOW TO USE?

FOLLOW THESE SIMPLE STEPS

1. MICRO-SEAL WITH GRAFFITI CONTROL should be applied using low-pressure airless or hand pump spray equipment.

2. Avoid atomizing material by using a spray tip size of .035 to .051. Spray head should be held 8 to 12 inches from the surface so that the flood coat runs down the wall approximately 6-12 inches below the point of application.

3. Avoid application in windy weather.

4. Trigger gun off at the end of each pass to avoid using excessive

materials. Stop all applications only at corners, joints, seams, or edges.

5. Apply second coat wet on wet after first coat has been allowed to penetrate for 20-30 minutes. Immediately roll or brush out runs and drips to ensure even appearance.

Chart above shows 1st coat coverage rate and 2nd coat coverage rate at 2x rate of 1st coat when 2nd coat is applied 20-30 min after 1st coat (example:  Dense Masonry surface project 1st coat 150 sq’/gallon and 2nd coat at 2x rate or 300 sq’/gallon).   When applying 2nd coat 1 to 3 days after 1st coat, apply 2nd coat at rate 50% more than 1st coat chart above>

GRAFFITI REMOVAL:

In many instances, non-abrasive household cleaners safely and effectively remove tagging. However, in the event tagging can’t be removed with these cleaners, then use Rainguard’s VANDLCLEAN SUPER GRAFFITI REMOVER for best results. Follow manufacturer’s recommendations and instructions for use. In addition, warm water power-washing has also been known to assist in the removal of tagging. Please refer to the manufacturer for additional assistance.

PRECAUTIONS & LIMITATIONS

1. All surfaces to be coated should be clean of any dirt and grime, efflorescence, lime run, form oils and release agents, grease, mud, excess mortar, and mold and mildew, etc.

2. All cracks should be pointed or caulked. All voids, bee holes, masonry surface defects and openings such as conduits, pipes, drains, door frames, vents, air conditioner openings, electrical openings, control joints, or any dissimilar materials should be repaired using urethane or other approved patching.

STORAGE

Store materials in a well-protected area between 45° and 90°F. Avoid freezing temperatures, direct sunlight, and moisture. Keep away from heat sources.

What is Micro-Seal with Graffiti Control?

Micro-Seal with Graffiti Control is a penetrating protective sealer designed to shield surfaces from graffiti, stains, and environmental damage. It creates an invisible barrier that allows for easy graffiti removal without damaging the underlying substrate.

How does Micro-Seal graffiti protection work?

Micro-Seal works by penetrating into porous surfaces and forming a clear, breathable barrier. This barrier prevents paints, inks, and dyes from bonding permanently, making graffiti easier to remove with appropriate cleaners. Micro-Seal with Graffiti Control provides both heavy-duty graffiti and water repellent performance on a wide variety of vertical and horizontal surfaces. It seals the pores of the surface, making graffiti easier to use. Check out VandlClean Graffiti Remover Spray for making graffiti easier to clean.

What surfaces can Micro-Seal be applied to?

Micro-Seal is ideal for a wide range of surfaces, including:

• Concrete
• Brick
• Masonry
• Stone
• Stucco
• Pavers
• Wood
• Unglazed Tile

It is especially effective on porous surfaces commonly targeted by graffiti.

Is Micro-Seal a sacrificial or permanent anti-graffiti coating?

Micro-Seal is typically considered a semi-permanent (durable) anti-graffiti solution. Unlike sacrificial coatings that require reapplication after cleaning, Micro-Seal offers multiple cleanings before reapplication is needed.

How do you remove graffiti from a Micro-Seal protected surface?

Graffiti can be removed using a compatible graffiti remover like our VandlClean Graffiti Remover Spray  without damaging the surface. In most cases:

1. Apply VandlClean Graffiti Remover Spray
2. Lightly agitate if needed
3. Rinse clean

Because of the protective barrier, graffiti does not penetrate deeply, making removal faster and easier.

Does Micro-Seal change the appearance of the surface?

No—Micro-Seal is designed to be clear and non-film forming, so it:

• Maintains the natural look of the substrate
• Does not create a glossy or artificial finish
• Preserves texture and color

Is Micro-Seal breathable?

Yes. Micro-Seal is breathable, allowing moisture vapor to escape while still blocking contaminants. This helps prevent:

• Trapped moisture
• Efflorescence issues
• Surface deterioration

How long does Micro-Seal graffiti protection last?

Longevity depends on exposure and cleaning frequency, but typically:

• Provides long-term protection (multiple years)
• Withstands multiple graffiti removals
• May require reapplication in high-traffic or high-vandalism areas

Can Micro-Seal be used in high-traffic or commercial areas?

Yes. Micro-Seal is commonly used for:

• Commercial buildings
• Public infrastructure
• Schools and campuses
• Parking structures
• Urban environments

Its durability makes it ideal for areas prone to repeated graffiti.

Is Micro-Seal environmentally friendly?

Most Micro-Seal formulations are designed to be:

• Low odor
• Low VOC
• Safer for use in populated areas

(Always confirm specific VOC compliance based on your region.)

Can Micro-Seal be applied over existing coatings?

It depends on the surface. Micro-Seal performs best when applied to clean, uncoated, porous substrates. Existing coatings may prevent proper penetration and reduce effectiveness. For specific help on YOUR project, reach out to us at 630-675-4509 or at [email protected].

What is the coverage rate for Micro-Seal?

Coverage varies depending on porosity:

• Dense surfaces: higher coverage (more sq ft per gallon)
• Porous surfaces: lower coverage

Testing a small area is recommended for accurate estimates. Check out our Coverage Rate tab to see coverage for each type of substrate required.

What makes Micro-Seal different from other anti-graffiti coatings?

Micro-Seal stands out because it:

• Penetrates instead of forming a surface film
• Maintains natural appearance
• Allows breathability
• Provides multi-clean protection (not just one-time use)

Is Micro-Seal good for historic or decorative surfaces?

Yes. Because it is invisible and non-film forming, it is ideal for:

• Historic masonry
• Architectural stone
• Decorative concrete

It protects without altering the original look.

Does Micro-Seal prevent all graffiti?

No product can prevent graffiti entirely, but Micro-Seal makes it significantly easier and faster to remove, reducing labor and long-term damage. To review all of our anti-graffiti coatings check out our Anti-Graffiti Page. For further help on YOUR project reach out to us at 630-675-4509 or [email protected].