Return to previous page
Filters
Show
E100V Vertical Wall Epoxy - blue Color

E100V Vertical Wall High Build Epoxy Coating | To 12 Mils No Sag | 12 Colors | Underwater Concrete

From: $50.00

  • No sagging on vertical walls to 12 mils per coat
  • Good chemical and abrasion resistance
  • Works well on underwater concrete decorative surfaces including pools and water features
  • Long 45 - 90 min pot life
  • Outstanding adhesion 475 psi @elcometer
  • Wide selection of 12 color options
  • 100% solids, very low voc
Select options
E100V Vertical Wall Epoxy Coating

E1015V Vertical Wall Epoxy Coating & Primer to 8 Mils No Sag | 11 Colors

From: $50.00

  • No sagging on vertical walls up to 8 mils per coat
  • Good for priming or coating concrete, wood or masonry.
  • Good chemical and abrasion resistance
  • Long 1 - 1.5 hour pot life
  • Excellent adhesion 425 psi @elcometer
  • Wide selection of 11 color options
  • Water base
Select options
E15M Epoxy for Steel and Concrete

E15M Epoxy Mastic Steel Primer DTM & Concrete Coating | Chemical Resistant | Low Temp 25F

From: $95.00

  • High solids DTM (direct-to-metal) chemical resistant steel primer or finish coat to steel and concrete
  • Self priming to steel including tight rust
  • Apply Vertical Surfaces to 8 mils DFT Steel & Concrete
  • Great primer for use with our E1500HN (horizontal) and E555VN (vertical) Novolac Chemical Resistant Epoxies
  • USDA Approved
  • Tight film, low permeability.
  • Exceptional adhesion Exceeds 500 psi
  • Excellent impact resistance 90 in lb
  • Excellent abrasion resistance CS 17 Wheel, 1000 cycles, 1000 g Load 21 mg loss
  • Excellent against rust “undercutting”
  • Easy to apply brush, roll and spray
  • Low temp cure version to 25°F
  • Available 13 colors
Select options
color chart

E370P Hi-Gloss Hi Build Polyurethane | Non-Yellowing | For Vertical Concrete and Steel | Walls

$125.00

  • High solids
  • A tile-like finish.
  • Low V.O.C.
  • Easy to clean
  • Good chemical and stain resistance
  • Highly resistant to abrasion and impact.
  • Excellent gloss and color retention
  • Outstanding wearing properties.
  • Non-chalking and non-yellowing
  • High film build
Select options

Out of stock

E505 Vertical Wall Epoxy Block Filler

E505V Vertical Wall Epoxy Concrete Block Filler to 20 Mils No Sag | 11 Colors

From: $117.00

  • No sagging on vertical concrete and cement block walls up to 20 mils per coat
  • Great epoxy block filler
  • Good chemical and abrasion resistance
  • Long 45 - 90 min pot life
  • Excellent adhesion 420 psi @elcometer
  • Wide selection of 11 color options
  • 100% solids, very low voc
Select options
E517M Epoxy Mastic For Steel and Concrete

E517M Flake Filled Epoxy Mastic Steel & Concrete Coating | Chemical Containment | Low Temp 25F

From: $120.00

  • Self Priming on steel
  • Excellent primary containment coating for internal tank linings (when part of specified system)
  • Excellent secondary containment coating
  • Performs well over epoxy mortars and properly primed concrete surfaces
  • Can be applied on damp surfaces
  • Excellent chemical resistance to acids, caustics, solvents
  • Outstanding impact and abrasion resistance.
  • Exceptional adhesion Exceeds 700 psi
  • Excellent flexibility pass 7/8" mandrel 180º Bend
  • Apply Vertical Surfaces to 15 mils one coat
  • Meets USDA requirements.
  • Low temp cure version to 25°F
  • Low VOC 72 grams/Liter
Select options
E555N Novolac Epoxy Chemical Resistant

E555VN Novolac Epoxy | Superior Steel & Concrete Chemical Vertical Protection | Tank Linings

$162.00

  • Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
  • For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
  • Vertical application to 10 mils DFT.
  • Great for Secondary Containment for both steel and concrete surfaces
  • Use as Primary Containment and Tank Linings when used as part of specified system
  • Excellent abrasion resistance with ceramic filler
  • Excellent in battery storage room areas.
  • Meets USDA requirements
  • May be applied in cold, damp conditions to 45°F with curing down to 35°F
Select options
E590 - E591 Wet Surface Epoxy

E591 Wet Surface Epoxy | Cures to 35°F For Concrete and Steel | Floors – Walls

From: $130.00

  • May be applied on wet or under water surfaces
  • Cold temperature application down to 35°F
  • Self-priming on steel and on most concrete applications
  • Long 40-50 POT Life at 75F
  • Ideal for marginally prepared and painted surfaces
  • Outstanding impact and abrasion
  • High film build - Up to 20 mil DFT per coat on horizontal surfaces
  • Vertical surfaces to 12 mils
  • Excellent coating for manholes
  • 100% solids and 0 g/L VOC's
  • 3 Colors Available
Select options

E903UCB Cove Base Urethane Mortar | HIgh Heat 250F | Anti-Fungal

From: $87.00

  • Easy construction of vertical cove bases
  • Seamless hygienic finish with no grout lines
  • Resistant fo fungi growth
  • Low odor, fast installation, fast cure
  • Thermal shock to 250F & chemical resistance
  • 3 color options
Select options
Efflorescence Blocker For Concrete Masonry Floors and Walls

Efflorescence Blocker Protects Concrete and Masonry Surfaces | Floors and Walls

From: $74.00

  • Blocks efflorescence & alkali from coming to surface
  • Concrete & Masonry Floors and wall Surfaces
  • Ideal for planters and groundwater penetration
  • Excellent exterior durability
  • Direct and reverse impact resistant
  • Works as a universal primer
  • Water and stain resistant
  • Wet and dry adhesion
Select options

Out of stock

Novolac Epoxy Acid Solvent Chemical Resistant NE253

NE253V Novolac Vertical Wall Colored Epoxy Chemical Resistant Acid Solvent

From: $57.00

  • Outstanding Spill & Splash Acid, Solvent, Chemical protection
  • Resistant to high concentration acids, some chlorinated solvents incl xylene, MEK
  • Apply up to 10 mils on vertical walls
  • Resists wide range of chemicals, solvents and acids
  • Medium build for chemical troughs and curbs
  • Great for tanks and chemical spill areas for cement, masonry or brick
  • Excellent adhesion 425 psi
  • Quick recoat 5-10 hrs
  • Selection of 3 color options
  • Low voc <40 g/L
Select options

NP-1 Cove Master Vertical Epoxy Mortar | 100% Solids | High Build | 4 Colors

From: $56.00

  • Easy construction of vertical cove bases
  • 100% Solids Commercial Grade Epoxy
  • High build formula
  • 5 color options
  • Comes as 3 part kit with aggregate or Liquid Only to add your own aggregate or NP1 can also be used as a primer.
Select options

Copyright 2021 by Exterior Performance Coatings