No products in the cart.
Return To ShopFree shipping Lower 48 States
$45.00
TECHNICAL INFORMATION |
|
---|---|
Color | Select 4 Mfg colors |
Sheen/Gloss Level | Flat Sheen |
Dry To Re-Coat | 1 hours |
#Coats Recommended | 1 – 2 coats |
Back in-service time | 2 hours to walk-on |
Application method | Low pressure hand pump or airless sprayer, brush, roller |
Where Can it be Used | All Interior|Exterior architectural surfaces |
Apply to New Concrete | 2 days |
Low Application Temperature | 40F|4.4C Surface & Air |
Base | Water |
VOC Content | <20 g/L |
Use on Material | All unpainted masonry, concrete and wood surfaces |
Satisfaction Guarantee | 3 years |
Certification/Test | |
---|---|
Leed 4.2 (1) point credit available | Meets LEED and SQAMD low VOC requirements |
Coverage Rate | Square Feet/Gallon |
---|---|
Wood | 200 |
Clay Brick | 125-150 |
Stucco | 100-150 |
Stone (stepping stones, cultured stones etc) | 100-125 |
Split Faced Block | 50-70 |
Precision Block | 6070 |
Lightweight Bock | 40-55 |
Adobe Block | 70-90 |
Clay Block | 50-60 |
Clay/Stone Pots | 60-70 |
Concrete | 125-150 |
*Textured surfaces | Decreases coverage rates |
Conditions Prior to Application | |
---|---|
Temperature (surface|air) | 40F to 90F (4.4C to 35C) and at least 5F above dew point |
Moisture of substrate | Less than 15% |
Humidity | Less than 90% |
Rain | No rain 24 hrs prior to, 24 hrs after application |
Cure time for newly poured concrete | Apply 10 days after pour |
Application method | Use low pressure hand pump or garden sprayer |
FOLLOW THESE SIMPLE APPLICATION STEPS
Application:
For a proper application, use a hand pumped garden sprayer. Apply 1 (one) heavy saturation coat to ensure the product can penetrate deep into the surface, sealing the pores or capillaries.
Once the 1st coat is dry to the touch apply the recommended 2nd saturation coat to ensure best results. Once the 2nd coat is completely dry you can now put any decor, furniture etc. back on the treated surface. IMPORTANT: Avoid letting any water to come in contact with your newly sealed surface for 24 hours. After full cure time is achieved (approximately 4-5 days) you can expect the full beading effect.
Wait to test water repellency after the full chemical cure period. To conduct a test, simply drip some water in a few places where you have sealed the surface, if the drips make the surface darken, this is an indication that it is still absorbing, meaning you need to apply another coating. (more common with older surfaces)
Vertical Surfaces:
Allow product to drip heavily before moving onto the next spot. Heavily saturate the surface maintaining at least a 6-inch drip or run down.
Horizontal Surfaces:
Apply the product until it starts to pool up slightly. You will know enough was applied in any given spot when the product starts to pool (puddle) up. The puddling will dissipate slowly into the pores so there is no need to back roll or brush them out.
Clean-Up: Clean-up is a breeze thanks to our water based formula. Simply rinse out equipment with fresh water after application until it runs clear. Any undesired over-spray on windows or glass can be immediately wiped off. If the product has already dried it can be cleaned off quickly with a rag, warm water, and a mild soap.
PRECAUTIONS & LIMITATIONS
1. All surfaces to be coated should be clean of any dirt and grime, efflorescence, lime run, form oils and release agents, grease, mud, excess mortar, and mold and mildew, etc.
2. All cracks should be pointed or caulked. All voids, bee holes, masonry surface defects and openings such as conduits, pipes, drains, door frames, vents, air conditioner openings, electrical openings, control joints, or any dissimilar materials should be repaired using urethane or other approved patching.
STORAGE
Store materials in a well-protected area between 45° and 90°F. Avoid freezing temperatures, direct sunlight, and moisture. Keep away from heat sources.
Certification/Test | |
---|---|
Leed 4.2 (1) point credit available | Meets LEED and SQAMD low VOC requirements |
Coverage Rate | Square Feet/Gallon |
---|---|
Wood | 200 |
Clay Brick | 125-150 |
Stucco | 100-150 |
Stone (stepping stones, cultured stones etc) | 100-125 |
Split Faced Block | 50-70 |
Precision Block | 6070 |
Lightweight Bock | 40-55 |
Adobe Block | 70-90 |
Clay Block | 50-60 |
Clay/Stone Pots | 60-70 |
Concrete | 125-150 |
*Textured surfaces | Decreases coverage rates |
$33.00 – $1,368.00
Weight | N/A |
---|---|
Dimensions | 12 × 6 × 10 in |
Color | |
CSI Spec | |
Product Material | |
Finish | |
Surface Applied To | |
Warranty | Standard 10 Year up to 20 Year Labor & Material Warranty |
Manufacturer |
Weight | N/A |
---|---|
Dimensions | N/A |
Color | |
Product Material | |
Finish | |
Surface Applied To | |
Warranty | 5 Year Labor & Material Warranty |
Manufacturer | |
CSI Spec | |
MPN | CR-0300 |
Weight | N/A |
---|---|
Dimensions | N/A |
Color | |
CSI Spec | |
Product Material | |
Finish | |
Surface Applied To | |
Warranty | 5 Year Labor & Material Warranty |
Manufacturer |
Copyright 2022 by Exterior Performance Coatings