Call us (630) 675-4509
Show
Filter by
Filter by
Filter by
Hot
5500 Polyaspartic Polyurea Coating Roll Down Low Temp 30°F | 87% Solids
From: $149.00- Beautiful Decorative High Gloss Appearance
- Cold Temperature Application to 30F using Fast Set
- Easy Squeegee/Roller Application
- Waterproof, Aliphatic Resists UV Non-Yellowing
- Indoor & Outdoor Floor and Countertop Projects
- Good In Submerged Service Projects Like Fountains
- Works well on concrete, brick, steel, wood, fiberglass
- Excellent Chemical & Abrasion Resistance
- Highly Adhesive, Flexible & Non-Brittle
- Optional Fast or Slow Set, High Heat & Humidty
- Great For Garage Floors Using Chips & Flakes
- Commercial and Industrial Applications
- Use as Stand Alone System or Topcoat to Epoxy
6007 Wet Condition Epoxy For Concrete & Steel | Low Temp 35°F
From: $593.00- Protect Problem Wet and Damp Areas
- Withstands to 20 PSI Hydralic Vapor Pressure
- Cold temperature down to 35°F
- Designed to Protect both Concrete and Steel
- Use as Primer With Topcoat or Floor Coating
- Offers Excelllent Moisture and Corrosive Protection with Outstanding Adhesion
- 100% Solids, no VOC, 2 Component
Hot
6009 Epoxy Floor Coating Industrial & Commercial Low Temp 35°F | 100% Solids | Quick Cure
From: $115.00- Commercial, Industrial, Residential Concrete Floors
- Cold temperature down to 35°F
- Tough - Attractive Looking Epoxy
- Good Chemical, Abrasion, Impact Resistance
- Quick 4 to 7 hour set time
- Self Priming With No Primer Required
- 100% Solids, no VOC, 2 Component
- Clear or Selection of Colors
- Excellent Protection at Lower Cost
Aspartic 100 High Build Polyaspartic for Concrete Floors | Low Temp 30°F | 100% Solids
From: $99.99- Tough, durable topcoat for interior epoxy floor coatings
- Very low to no odor great for sensitive odor indoor projects
- Can be used as high build topcoat up to 16 mils or 100 sq'/gallon
- Cold temperature application down to 30°F
- Excellent chemical and abrasion resistance
- UV Stable, Will Not Yellow
- Beautiful high gloss appearance
- Designed for high traffic and industrial areas
- High solids 100%
- Available clear & 14 colors (Pigment Sold Separate)
Aspartic 85 Polyaspartic Quick Cure Concrete Floor Coating | Low Temp 30°F
From: $79.50- Tough, durable topcoat for interior epoxy floor coatings
- Cold temperature application down to 30°F
- Fast Curing for quick 5-7 Hours Back in-Service Light Foot Traffic
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
- Designed for high traffic and industrial areas
- High solids 85%
- Available in clear & 14 colors (Colored Pigment Sold Separately)
DT-454 Epoxy Quick Cure UV Concrete Floor Coating Low Temp 40F | 100% Solids
From: $70.00- Tough, Durable Epoxy Coating
- Quick cure 6-7 hour recoat time
- Outstanding Bonding
- UV Resistant
- Good chemical, impact and abrasion resistance
- Cold temperature application down to 40F
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 14 colors! (Pigment sold separately)
E-Green Polyurea Basecoat for Concrete Floors | Low Temp 40°F | 100% Solids | 300% Elongation
From: $65.00- Tough, durable plant based Polyurea Coating
- Extreme Flexibility (300% Elongation)
- Exceptional Adhesion >500 psi ASTM D4541
- Cold temperature application down to 0°F
- Can be used as high build basecoat up to 16 mils or 100 sq'/gallon
- Excellent chemical and abrasion resistance
- Designed for high traffic and industrial areas
- 100% Solids Performance
- Available in clear & 14 colors!
- Quick Cure 1 Day System
- Little to NO ODOR
E15M Epoxy Mastic Steel Primer DTM & Concrete Coating | Chemical Resistant | Low Temp 25F
From: $95.00- High solids DTM (direct-to-metal) chemical resistant steel primer or finish coat to steel and concrete
- Self priming to steel including tight rust
- Apply Vertical Surfaces to 8 mils DFT Steel & Concrete
- Great primer for use with our E1500HN (horizontal) and E555VN (vertical) Novolac Chemical Resistant Epoxies
- USDA Approved
- Tight film, low permeability.
- Exceptional adhesion Exceeds 500 psi
- Excellent impact resistance 90 in lb
- Excellent abrasion resistance CS 17 Wheel, 1000 cycles, 1000 g Load 21 mg loss
- Excellent against rust “undercutting”
- Easy to apply brush, roll and spray
- Low temp cure version to 25°F
- Available 13 colors
E322HW High-Gloss Aliphatic Urethane Abrasion & Chemical Resistant Low Temp 45°F
From: $60.00- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Cold temperature application down to 45°F
- Excellent abrasion resistance Only 22 mg loss (Tabor Abrasion test) Reduced to 10 mg loss using our High Wear 325 additive
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
- Easy to Use with Long 2-4 Hour Pot Life
- Great for both Indoor and Outdoor Concrete Floor Projects
- Comes in wide Variety of Clear and 18 Different Colors
- Solvent Based - Excellent adhesion
E322SG Semi-Gloss Aliphatic Urethane Abrasion & Chemical Resistant Low Temp 45°F
From: $60.00- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Cold temperature application down to 45°F
- Excellent abrasion resistance Only 24 mg loss (Tabor Abrasion test) Reduced to 12 mg loss using our High Wear 325 additive
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
- Easy to Use with Long 2-4 Hour Pot Life
- Great for both Indoor and Outdoor Concrete Floor Projects
- Comes in wide Variety of Clear and 18 Different Colors
- Solvent Based - Excellent adhesion
E517M Flake Filled Epoxy Mastic Steel & Concrete Coating | Chemical Containment | Low Temp Cure...
From: $125.00- Self Priming on steel
- Excellent primary containment coating for internal tank linings (when part of specified system)
- Excellent secondary containment coating
- Performs well over epoxy mortars and properly primed concrete surfaces
- Can be applied on damp surfaces
- Excellent chemical resistance to acids, caustics, solvents
- Outstanding impact and abrasion resistance.
- Exceptional adhesion Exceeds 700 psi
- Excellent flexibility pass 7/8" mandrel 180º Bend
- Apply Vertical Surfaces to 15 mils one coat
- Meets USDA requirements.
- Low temp cure version to 25°F
- Low VOC 72 grams/Liter
E591 Wet Surface Epoxy | Apply Underwater | Cures to 35°F | Concrete – Steel | Floors – ...
From: $120.00- May be applied on wet or under water surfaces
- Cold temperature application down to 35°F
- Self-priming on steel and on most concrete applications
- Long 40-50 POT Life at 75F
- Ideal for marginally prepared and painted surfaces
- Outstanding impact and abrasion
- High film build - Up to 20 mil DFT per coat on horizontal surfaces
- Vertical surfaces to 12 mils
- Excellent coating for manholes
- 100% solids and 0 g/L VOC's
- 3 Colors Available
E650 Non-Skid Epoxy Floor & Deck Low Temp 25°F | OSHA ADA Navy Spec Mil-PRF-24667B
From: $107.00- Heavy duty non-skid resistance for concrete & steel
- Available in regular cure and cold temp formula to 25°F
- Designed for wet areas
- Meets ADA and OSHA requirements for safe co-efficient of friction (COF) when properly applied
- Meets Navy Military Specification Mil-PRF-24667B for Non-Skid Deck Coatings
- Excellent adhesion, abrasion and impact resistance
- Resistant to grease, oil, salt water, alcohol, detergent, gasoline, hydraulic fluid
- Excellent coating for Diamond Plate
- Easy to apply, ready to use non-skid coating
- Comes in 4 colors
H20 HyperPRIME Epoxy Quick Cure Bonding Primer | Low Temp 45°F | 3 Hr Recoat
From: $40.00- Excellent Substrate Penetration with superior adhesion 450 psi
- Great for concrete, wood and metal surfaces
- Helps protect Against Coating Damage from Outgassing of Concrete
- Quick Cure With 3 Hour Recoat Time - great for 1 day floor coating systems
- Available in Clear plus 6 Colors
- Water Base, No Offensive odors
- Cold temperature application down to 45F
- Good chemical and Stain Resistance
- Easy Application
HyperBOND Epoxy | Wet Condition Moisture Tolerant | Concrete Floor Coating | Low Temp 40F | 100% Sol...
From: $60.00- Tough, Durable Epoxy Coating
- Outstanding Bonding
- Water Insensitive and Can Be Applied In Wet Conditions
- Withstands up to 9 lbs. of hydrostatic pressure
- Cold temperature application down to 40F
- Long 30-35 min working time
- Resistant to Blushing/Sweating
- Good chemical, impact and abrasion resistance
- High solids 100%
- Available in clear & 13 colors! (Pigment sold separately). In 3 gallon kits only, available pre-colored in 3 colors
HyperFLEX Epoxy | Flexible Membrane Concrete Wood Steel | 150% Elongation | Low Temp 40°F | 100% Sol...
From: $74.00- Tough, Durable Epoxy Coating and Flexible Membrane
- Very Flexible with Elongation rating 150% @ASTM D-638
- Great for Quick Crack Repair and Control Joint Filler (when mixed with Fumed Silica)
- Can be used as a (1) basecoat for full broadcast floors, (2) flexible membrane, (3) repair gel to fill joints, cracks, & divots
- Cold temperature application down to 40°F
- Concrete & Wood Floors and Countertops
- Superior Flexibility and Outstanding Bonding
- Rapid Cure Rate For Same Day Flake and Solid Color System Application
- When used as membrane or basecoat HyperFLEX cures about 2 hours
- When used for gel repair cures about 10-15 minutes
- Good chemical and abrasion resistance
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 13 colors! (Pigment sold separately)
HyperREZ UV Epoxy Concrete Floor Coating | 45 min Work time | 100% Solids | Ultra Clear Great for Me...
From: $70.00- Tough, durable epoxy floor and countertop coating
- Cold temperature application down to 40F
- High Build Applications up to 32 mils/coat (50 sq'/gal)
- Long Working Time
- Good chemical and abrasion resistance
- UV Resistant
- High gloss appearance
- Designed for high traffic and industrial areas
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 14 colors (Colored Pigment Sold Separately)
Copyright 2024 by Exterior Performance Coatings LLC