Shop
Filter By Category
Questions about our products?
Call or Text us for help picking the correct solution for your project. (630) 675-4509
Showing 1–50 of 74 results
-
1007 Polyurea Coating Fast Set Waterproof Elastomeric Spray | Flexible 600%+ Elongation | 10-30 Second Set Time | 100% Solids
- Excellent elongation – 600%+
- Protects wide variety surfaces - concrete, metal, wood etc
- Chemical Resistant
- High Impact & Abrasion Resistance
- Application temperature range 20°F to 200°F
-
5500 Polyaspartic Polyurea Coating Roll Down Low Temp 30°F | 87% Solid
- Beautiful Clear Appearance
- Quick recoat time in as little as 1 – 1.5 hours
- Waterproofing Elastomeric Systems
- Good In Submerged Service Projects Like Fountains
- Works well on concrete, brick, steel, wood, fiberglass
-
5500HS 100% Solids Polyaspartic Polyurea Coating Roll Down | Low Temp 30°F | Flexible 120% Elongation | 1:2 Mix Ratio | 1 Coat Coverage
- Beautiful Clear HIGH GLOSS Appearance
- 100% Solids For Thick 1 Coat Coverage Full Flake, Quartz, Silica Sand Systems to 16 mils DFT (100 sq'/gallon)
- Quick 24 hour back in-service (at 75F)
- Waterproofing Elastomeric Systems
- Good In Submerged Service Projects Like Fountains
-
5500M Matte Finish Polyaspartic Polyurea Coating Roll Down | Low Temp 30°F | 89% Solids | Flexible 120% Elongation
- Beautiful Clear MATTE FINISH Appearance
- Quick recoat time in as little as 1 – 1.5 hours and 24 hour back in-service (at 75F)
- Waterproofing Elastomeric Systems
- Good In Submerged Service Projects Like Fountains
- Outstanding Chemical Resistant
-
6007 Wet Condition Epoxy For Concrete & Steel | Low Temp 35°F | 100% Solids
- May be applied in damp and wet conditions where wash-down of areas is problematic
- Withstands up to 15-18 psi hydraulic vapor pressure
- Provides protective attractive color coat epoxy flooring system
- Excellent working properties
- Exceptional corrosion protection of both concrete and steel
-
6009 Epoxy Floor Coating Industrial & Commercial Low Temp 35°F | 100%
- Protective and attractive color coat epoxy flooring system
- Designed to seal floors against abrasion, water, oils and chemicals
- Good Color stability
- Wide application temperature range 35°F to 125°F (1.7°C to 52°C)
- Quick re-coat time 4-5 hours (at 75°F)
-
7001 Polyurethane Primer Concrete & Steel | Quick Cure | Exceptional Adhesion | Low 35F Temp
- Concrete & Steel Primer For Epoxy, Urethane, Polyaspartic, Polyurea Coatings
- Cross-links With Polyurea, EPDM Roofing and other Plastic Materials Difficult to Bond to
- Deep Penetrating Exceptional 1200 psi Adhesion
- Superior Corrosion, Abrasion and Water Resistance
- For Use in Submerged Service Applications
-
ARCRETE Epoxy Primer & Rebuild | Horizontal | Secondary Containment| Repair, Smooth or Level |100% Solids
- Rebuild for Repair, Smoothing or leveling of Horizontal Areas
- Solvent and VOC free product
- Used in High Build Areas
- Chemically Resistant
- Rapid Turnaround
-
Aspartic 100 High Build Polyaspartic for Concrete Floors | Low Temp 30°F | 100% Solids
- Tough, durable topcoat for interior epoxy floor coatings Very low to no odor great for sensitive odor indoor projects Can be used as high build topcoat up to 16 mils or 100 sq'/gallon Cold temperature application down to 30°F Excellent chemical and abrasion resistance UV Stable and will not yellow Beautiful high gloss appearance Designed for high traffic and industrial areas 100% Solids Performance Available in clear & 14 colors!
-
Aspartic 85 Polyaspartic Quick Cure Concrete Floor Coating | Low Temp 30°F
- Tough, durable topcoat for interior epoxy floor coatings
- Cold temperature application down to 30°F
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
-
Aspartic 85 Slow Set Polyaspartic Concrete Floor Coating | Low Temp 30°F | Low Odor Option
- Tough, durable topcoat for interior epoxy floor coatings
- Cold weather application down to 30°F
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
-
Bio-Chem E330 High Performance Epoxy | 100% Solids | Aggressive Chemical Exposures | High Heat
- Down-Hole Tubular Coating: Id and OD coating, especially suitable for "Ruffcoat" OD treatment
- Tank Lining: High hydrocarbon chemical resistance and early return to service make Bio-Chem E330 an ideal high build tank lining
- Hopper Car Lining: excellent physical and chemical resistance properties
- Concrete Containment: Excellent physical and chemical resistance properties
-
Bio-Dur E3000 Wet Surface High Temperature Epoxy Coating | Up To 350°F
- Anticorrosive Coating: Splash zone, excellent abrasion resistance above or below water
- Encapsulating Coating: Smooth, dense, easily decontaminated coating for steel and concrete
- High Heat, Anti-Abrasion Coating: High Tg coating with hard, abrasion-resistant pigmentation
- Repair Compound: Patching, leak sealing, etc. above and below water
- Wastewater: Reinforces, smooths, and protects concrete exposed to chemical or municipal waste
-
Bio-Dur E3050 Novolac Epoxy | High Temperature | Wet or Dry Surface Ap
- Encapsulating Coating: Smooth, dense, easily decontaminated coating for steel and concrete
- High Heat, Anti-Abrasion Coating: High Tg coating with hard, abrasion-resistant pigmentation
- Tank and Pipeline Liner: Chemical Resistance and high hardness create durable corrosion protective barrier
- Wastewater: Reinforces, smooths and protects concrete exposed to chemical or municipal waste
-
Bio-Flor E182 Acid Resistant Floor Epoxy | Fast Cure | Self Leveling | 100% Solids | Air Shippable
- Loading Docks: Generally used with aluminum oxide abrasive for maximum durability and traction. Reduces or eliminates sweating following sudden changes in weather from cold to hot and humid.
- Vinyl Asbestos Tile: Encapsulates after preparation by OSHA approved scrubbing. Seals and creates a tough, seamless flooring in any color.
- High Gloss
- 100% Solids
-
Bio-Flor E183 High Temperature Resistant Floor Epoxy | Fast Cure | Sel
- Loading Docks: Used with aggregate to add durability and traction. Reduces or eliminates sweating following sudden changes in weather from cold to hot and humid.
- High Temperature Exposure: Added high temperature components provide increased temperature resistance to dry heat and direct contact
- Vinyl Asbestos Tile: Encapsulates after preparation by OSHA approved scrubbing. Seals and creates a tough, seamless flooring in any color.
- High Gloss
- 100% Solids
-
Bio-Seal E206 Epoxy Coating | High Temperature Application | 100% Solids | VOC free | Up to 40 mils
- High Temperature Coating: for pipelines, tanks and other equipment. Provides outstanding protection against environment exposures and hydrocarbons
- High Temperature Service
- Ambient Hardening
- Single coat application up to 40 mils
- Long overcoat window
-
Bio-Seal E907 Resin | High Heat Tolerance | Quick Return to Service
- Saturation Resin: For use with reinforcing fibers and fabrics to create composite repairs of tank tops, pipes or similar structures
- Pressure Transfer Compound: Very high compressive strength and modulus provides an excellent material for void and annulus filing of pipe sleeves, void spaces, etc.
- Penetrating Sealer: Use to seal and protect concrete, brick and other similar surfaces against chemical attack and water penetration
-
Chem-Put E32 High Build Epoxy Coating for Chemical Exposures | 100% Solids
- Concrete Repair: High Build Application allows for concrete resurfacing after attack by chemical exposure
- Marine and Offshore: Heavy Duty Repair and sealing compound in wet environments
- Repair Compound: Patching, leak sealing, etc. above and below water on steel and concrete substrates
- Tank Lining: High hydrocarbon chemical resistance with early return to service makes an ideal high build tank lining
- 100% Solids
-
DT-454 Epoxy Quick Cure UV Concrete Floor Coating Low Temp 40F | 100% Solids
- Tough, Durable Epoxy Coating
- Quick cure 6-7 hour re-coat time
- Outstanding Bonding
- Good chemical, impact and abrasion resistance
- UV Resistance
-
E100 Urethane Primer Finish Coat | Aluminum Galvanized & Rusty Steel | Dry Heat to 400 °F | Apply Down to18°F | Quick Cure
- Prime over Steel, metal, weathered galvanized steel, aluminum, fiberglass, polyurethane foam and previously painted surfaces
- Fast recoat 1-2 hours at 75°F & 50% R.H
- Cures down to 18°F dry and apply to 140°F
- High heat resistance up to 400°F dry
- Single component, easy to use
-
E101C Moisture Cured Urethane Clear Heavy Traffic Floor Sealer | Dustproofer | Prevents Spalling
- Great heavy duty stain resistant floor sealer for warehouse and other heavy use areas
- Excellent adhesion and sealer for concrete, wood and masonry surfaces.
- Extremely hard, yet flexible film.
- Outstanding “wearing properties
- Highly resistant to abrasion and impact.
-
E104 Primer Moisture Cured Urethane Zinc Rich Primer
- Excellent "wetting out" and adhesion to sound rusty steel
- Fast recoating within 4 hours at 75F
- Cures down to 25F on dry surfaces
- "Open" recoat window with proper cleaning
- Passed 1,500 hours in salt spray cabinet
-
E116 Rust Inhibitive Epoxy Primer
- Excellent rust preventing properties
- Excellent resistance to "under cutting"
- Good flexibility and abrasion resistance
- Long recoat up to 6 months
- Outstanding adhesion and "wetting out" ability
-
E139FL Flexible Epoxy Primer & Floor Coating | 60% Elongation | 100% Solids | Indoor & Outdoor
- Exceptionally flexible epoxy with 60% elongation
- High Build up to 50 mils thick per coat
- 100% Solids Commercial Epoxy
- Excellent Adhesion 450 psi
- Tough Abrasion resistant Only 6 mg loss (Tabor test) and 160 inch lbs Gardner variable impact test
-
E145 Polyamide Epoxy Block Filler | Concrete Block & Masonry Vertical Walls | High Build to 11.5 Mils DFT One Coat
- Excellent Adhesion to Vertical Block and Masonry Surfaces
- Excellent filling properties provide ideal "hold out"
- High Build Apply to 11.5 mils DFT (dry film thickness) One Coat
- Basecoat for high performing coating systems
- Hard film with high impact
-
E1501HN Novolac Epoxy (Replaces E1500HN) | Superior Steel & Concrete Chemical Horizontal Protection | Secondary Containment
- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
- Great horizontal chemical protection for Secondary Containment for both steel and concrete surfaces
- Thin film self leveling to 40 mils DFT one coat
- Extremely tough with high wearing properties
-
E15M Epoxy Mastic Steel Primer DTM & Concrete Coating | Chemical Resistant | Low Temp 25F
- High solids DTM (direct-to-metal) chemical resistant steel primer or finish coat to steel and concrete
- Self priming to steel including tight rust
- Apply Vertical Surfaces to 8 mils DFT Steel & Concrete
- Great primer for use with our E1500HN (horizontal) and E555VN (vertical) Novolac Chemical Resistant Epoxies
- USDA Approved
-
E1703 Epoxy Concrete Primer & Sealer | 100% Solids | Chemical & Abrasion Resistant | Easy to Apply | Low VOC
- Outstanding as a primer on concrete
- Good abrasion resistance
- Excellent adhesion to concrete surfaces
- Used as a clear sealer for concrete floors
- Non-toxic when cured
-
E1850 Epoxy Floor Coating | 100% Solids | High Gloss | Abrasion Resistant | Long 30-40 Min Work Time | High Build To 60 Mils DFT One Coat
- Easy to Use With Long to 40 Min Work Time
- 100% solids
- Extremely high gloss, tile-like finish
- Outstanding wear and abrasion resistance
- Good resistance to blushing
-
E1875 Epoxy Resin | Chemical Resistance | 100% Solids
- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 70% Sulfuric Acid, 37% HCL and 50% Sodium Hydroxide
- Extremely tough with high wearing properties
- Excellent abrasion and impact resistance
- Good adhesion to concrete
-
E1900/E1901 Polyaspartic Clear Topcoat | 40-50 Min Work Time | Quick Cure | High Solids | Apply 40°F – 100°F | Chemical Abrasion Impact Resistant
- Excellent Clear Top coat for decorative flake and quartz granule systems and solid color epoxy coatings.
- Fast set back in service as quick as 5 hours for foot traffic at 75F
- Resistant to hot tire pick up.
- Highly resistant to chemical, abrasion and impact
- Meets USDA requirements for incidental food contact
-
E2.8 Poly-Chemcure Primer | Fast Recoat | Low-Temp | OEM/Steel Fabricator
- High performance primer can be prepared on carbon steel, galvanized steel and aluminum
- Recoating in 90 minutes is possible for maximum productivity
- No induction time and longer pot life will improve productivity
- A smooth, sandable primer at 3 mils DFT over abrasive blasted or power tool cleaned substrate is needed for additional corrosion resistance
- Application by brush and roller, in addition to spraying, may be necessary
-
E275 High Build Polyamide Epoxy Mastic | Chemical Resistant | Excellent Adhesion to Steel
- Excellent adhesion to steel
- Meets USDA Requirements
- A high build primer or finish coat
- Excellent against "undercutting"
- Can be applied up to 12 mils DFT
-
E322HW High-Gloss Aliphatic Urethane Abrasion & Chemical Resistant Low
- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Excellent abrasion resistance Only 22 mg loss (Tabor Abrasion test) Reduced to 10 mg loss using our High Wear 325 additive
- Cold temperature application down to 45F
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
-
E322SG Semi-Gloss Aliphatic Urethane Abrasion & Chemical Resistant Low
- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Excellent abrasion resistance Only 24 mg loss (Tabor Abrasion test) Reduced to 12 mg loss using our High Wear 325 additive
- Cold temperature application down to 45F
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
-
E344QC Polyaspartic Quick Cure Concrete Floor Coating | 85% Solids
- Tough, durable topcoat for interior epoxy floor coatings
- Excellent chemical and abrasion resistance
- UV Stable and will not yellow
- Beautiful high gloss appearance
- Fast Curing for quick back in-service
-
E356HG High Gloss Urethane Moisture Cured | Exceptional Abrasion & Chemical Resistance | UV Stable
- Superior abrasion resistance Only 4.4 mg loss (Tabor Abrasion test)
- Outstanding Chemical Resistance
- Excellent durability with impact resistance of 100 in lb (Gardner Impact test)
- Aliphatic, UV Stable and will not yellow
- Easy to Use One Part with Long 3-5 Hour Pot Life
-
E370P Hi-Gloss Hi Build Polyurethane | Non-Yellowing | For Vertical Concrete and Steel | Interior & Exterior | 21 Colors
- Great Interior & Exterior Vertical Concrete & Steel Protection
- Exceptional Exterior Durability
- High solids
- Tile-like finish.
- Easy to clean
-
E374 Clear Satin Polyurethane | Non-Yellowing | For Vertical Concrete and Steel | Walls
- Great Interior & Exterior Vertical Concrete & Steel Protection and as topcoat for light to medium duty foot traffic only applications
- Exceptional Exterior Durability
- High solids
- Easy to clean
- Good chemical and stain resistance
-
E398 High Build Acrylic Polyurethane | High Gloss
- Excellent weather resistance
- High Solids
- Low VOC
- Good chemical and stain resistance
- Excellent gloss and color retention
-
E444X Polyaspartic High Gloss Concrete Floor Coating | 84% High Solids | Non-Yellowing | Low Odor
- Tough, durable topcoat for epoxy floor coatings
- Indoor and Outdoor Application
- Can be Applied Direct to Concrete
- High solids 84%
- Easy to work with 1:1 mix ratio
-
E449 Polyaspartic Fast Cure High Gloss Concrete Floor Coating | 95% High Solids
- Tough, durable topcoat for epoxy floor coatings
- High solids 95%
- Quick back in service 3-5 hours light foot traffic
- Can be applied up 12 mils thick one coat (125 sq'/gallon)
- Excellent chemical and abrasion resistance
-
E450SF Polyaspartic Slow Cure High Gloss Concrete Floor Coating | 90% Solids (Formerly E449SF)
- Tough, durable topcoat for interior epoxy floor coatings
- High solids 90%
- Long Working time 20-25 min
- Can be applied up 12 mils thick one coat (120 sq'/gallon)
- Excellent chemical and abrasion resistance
-
E5015 Epoxy Primer WB Coating | Concrete Wood Masonry | 20 Colors
- Versatile product good on concrete, masonry, wood surfaces
- Available in Clear and 20 Colors To Match With Topcoat
- Excellent as primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Long 1 - 1.5 hour pot life
-
E5030CL Urethane Clear Sealer / Topcoat WB
- Attractive, clear aliphatic non yellowing finish
- Versatile product good on concrete and masonry surfaces
- Recoat only 1-2 hours & light foot traffic 2-4 hours
- Extended 24 hour pot life
- Excellent abrasion resistance (Taber Abrasor test only 10 mg loss)
-
E517M Flake Filled Epoxy Mastic Steel & Concrete Coating | Chemical Containment | Low Temp Cure 25F | Extremely Flexible
- Self Priming on steel
- Excellent as a primary containment coating for internal tank linings (when part of specified system)
- Excellent as a secondary containment coating
- Performs well over epoxy mortars and properly primed concrete surfaces
- Can be applied on damp surfaces
-
E5520 Low Gloss Urethane Water Base Abrasion & Chemical Resistant
- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Excellent abrasion resistance Only 23 mg loss (Tabor Abrasion test) Reduced to as low as 10 mg loss using our High Wear 325 additive
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
- Great for Indoor Concrete Floor Projects
-
E5521 High Gloss Urethane Water Base | Abrasion & Chemical Resistant | Low Odor | Vapor Permeable
- Outstanding durability with impact resistance of 120 in lb (Gardner Impact test)
- Excellent abrasion resistance Only 21 mg loss (Tabor Abrasion test) Reduced to as low as 10 mg loss using our High Wear 325 additive
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
- Great for Indoor Concrete Floor Projects
-
E555VN Novolac Epoxy | Superior Steel & Concrete Chemical Vertical Protection | Tank Linings
- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
- Vertical application to 10 mils DFT.
- Great for Secondary Containment for both steel and concrete surfaces
- Use as Primary Containment and Tank Linings when used as part of specified system