Paver Sealer & Water Repellent Premium Grade

APPLICATION INSTRUCTIONS

WORKING WITH CONCENTRATES

FOLLOW THESE SIMPLE APPLICATION STEPS

Clean and Prep:

Before pressure washing apply and brush out stains using Cleaner/Prep manufactured by Rainguard and available here on our website. Ensure the surface is clean and “bone dry”, thus allowing the sealer to absorb into the surface.

Application:

For a proper application, use a hand pumped garden sprayer. Apply 1 (one) heavy saturation coat to ensure the product can penetrate deep into the surface, sealing the pores or capillaries. Once the 1st coat is dry to the touch apply the recommended 2nd saturation coat to ensure best results. Once the 2nd coat is completely dry you can now put any decor, furniture etc. back on the treated surface. IMPORTANT: Avoid letting any water to come in contact with your newly sealed surface for 24 hours. After full cure time is achieved (approximately 4-5 days) you can expect the full beading effect.

Wait to test water repellency after the full chemical cure period. To conduct a test, simply drip some water in a few places where you have sealed the surface, if the drips make the surface darken, this is an indication that it is still absorbing, meaning you need to apply another coating. (more common with older surfaces)

Vertical Surfaces:

Allow product to drip heavily before moving onto the next spot. Heavily saturate the surface maintaining at least a 6-inch drip or run down.

Horizontal Surfaces:

Apply the product until it starts to pool up slightly. You will know enough was applied in any given spot when the product starts to pool (puddle) up with a milky-white color. The puddling will dissipate slowly into the pores so there is no need to back roll or brush them out.

Clean-Up:

Clean-up is a breeze thanks to our water based formula. Simply rinse out equipment with fresh water after application until it runs clear. Any undesired over-spray on windows or glass can be immediately wiped off. If the product has already dried it can be cleaned off quickly with a rag, warm water, and a mild soap.

PRECAUTIONS & LIMITATIONS

1. All surfaces to be coated should be clean of any dirt and grime, efflorescence, lime run, form oils and release agents, grease, mud, excess mortar, and mold and mildew, etc.

2. All cracks should be pointed or caulked. All voids, bee holes, masonry surface defects and openings such as conduits, pipes, drains, door frames, vents, air conditioner openings, electrical openings, control joints, or any dissimilar materials should be repaired using urethane or other approved patching.

STORAGE

Store materials in a well-protected area between 45° and 90°F. Avoid freezing temperatures, direct sunlight, and moisture. Keep away from heat sources.

What is a paver sealer and why do I need it?

A paver sealer is a protective treatment designed to penetrate and protect concrete, brick, or stone pavers from water damage, stains, and weathering. A high-quality silane/siloxane paver sealer creates a deep, breathable barrier that helps extend the life of your pavers while maintaining their natural look.

How does a water repellent paver sealer work?

Premium paver sealers use silane and siloxane technology to penetrate below the surface and chemically bond within the pores. This creates a hydrophobic (water-repelling) barrier that reduces water absorption, helping prevent:

• Cracking from freeze-thaw cycles
• Mold, mildew, and algae growth
• Staining from oil, dirt, and debris

Will this paver sealer change the appearance of my pavers?

No—this is a clear, natural-look penetrating sealer. It does not leave a glossy film or alter the color of your pavers. Instead, it preserves the original appearance while protecting from the inside out.

What surfaces can this paver sealer be used on?

This premium water repellent is ideal for:

• Any pavers wherever they are used
• Driveways, patios, walkways, and pool decks

Is this better than a wet-look or glossy paver sealer?

It depends on your goal:

• Penetrating (this product):
  • Natural look
  • Long-lasting protection
  • No peeling or re-coating issues
• Topical/wet-look sealers (like other Wet Look Sealers):
  • Adds shine and color enhancement
  • May require more maintenance
  • Can peel or wear unevenly over time

For durability and low maintenance, penetrating sealers are typically preferred.

How do I apply paver sealer?

Application is simple:

1. Clean the surface thoroughly and allow it to dry
2. Apply using a hand pumped garden sprayer
3. Once the first coat is dry to the touch, apply the recommended 2nd saturation coat to ensure best results.
4. Let cure for approximately 4-5 days

Pro tip: Apply in dry conditions with no rain in the forecast.

How much coverage will I get?

Coverage depends on surface porosity, but typical rates are:

• 125–150sq. ft. per gallon (first coat)
• More coverage on denser surfaces

Highly porous pavers may require a second coat. For assistance ensuring you have the right quantity for YOUR project reach out to us at 630-675-4509 or [email protected].

Is this paver sealer safe for the environment?

Yes—most premium water-based silane/siloxane sealers are:

• Low VOC
• Non-toxic once cured
• Safe for surrounding landscaping

Can I apply this over an existing sealer?

It depends:

• Penetrating sealers: Usually yes, if the surface is clean and absorbent
• Film-forming sealers: Must be removed before application

If water no longer absorbs into the surface, stripping may be required. For additional assistance on YOUR project, reach out to us at 630-675-4509 or [email protected].

What makes this premium grade paver sealer different?

Compared to standard sealers, premium formulas offer:

• Higher concentration of active ingredients
• Deeper penetration
• Longer-lasting protection
• Better resistance to water and stains

When is the best time to seal pavers?

The best time is:

• After installation (once pavers are clean and dry)
• During mild weather (50°F–90°F)
• When no rain is expected for 24–48 hours

How do I know if my pavers need sealing?

Try a simple water test:

• If water soaks in quickly → time to seal
• If water beads up → protection is still active