HyperFLOW Metallic Epoxy

Adhesion350 psi @elcometer (concrete failure, no delamination

COVERAGE RATE

Surface porosity, temperatures, and application method will cause coverage rate to vary

CURE SCHEDULE @ 75F

APPLICATION TEMPERATURE: 45-90 degrees F with relative humidity below 85%

MIXING AND APPLICATION INSTRUCTIONS

MIXING PROCEDURE 

1. Pre condition product to temperature between 70-80F for best results
2. Add 12 oz of metallic pigment to A-Component in its respective container and mix using Jiffy mixer and drill at slow speeds for 5-10 mins until thoroughly homogenous
   1. Best to mix metallic pigment into A component and let saturate for 24 hours and pre-mix again prior to use
3. Pre-Mix B-Component in its respective container using clean Jiffy mixer and drill at slow speeds for 30 seconds or until thoroughly homogenous
4. Transfer A-component and B-component at a mix rate of 2A:1B by volume and mix for 2-3 minutes being sure to scrape sides of the bucket ensuring both components are thoroughly blended
   1. Do not mix at high RPMS or air entrapment may occur
   2. Do not pull mixing paddle in and out of the mix during process or air entrapment may occur

Use of an improper drill mixer can result in streaking of the color because the pigment has not been thoroughly blended.  It can also create curing problems if the hardener also called activator (Part B) is not thoroughly blended with the resin (Part A) which can cause some areas on your floor to remain soft and not harden properly.  DO NOT USE A PAINT MIXER.  Many mixing problems described above can be traced back to using a paint mixer..  DO NOT HAND MIX as this approach can also result in the same problems as using a paint mixer.

****IMPORTANT NOTE AFTER MIXING:****

Once parts A&B are thoroughly mixed, immediately pour 100% of all mixed product on the floor in a ribbon pattern, S or W shape over the area you want that amount of product to cover. The risk of leaving product in the bucket is that it will become hard and reduce the working time by a minimum of 50% and may harden and start smoking in the bucket before you get back to it.

Buildcoat: 50 Ft2 / Gal @ 32 Mils WFT • 60-65 Minute Working Time @ 52°F

• 40-45 Minute Working Time @ 70°F

• 25-30 Minute Working Time @ 88°F

COVERAGE RATES & WORKING TIMES

• Surface porosity, temperatures, and application method will cause coverage rate to vary.

• Ambient temps & humidity, product and surface temps, airflow and mix time affect overall

working times

APPLICATION PROCEDURE 

**Epoxy Sets faster in mass; Mixed material should not remain in bucket

**Be mindful of environmental variables and affects on estimated work times

1. .Pour mixed material across the surface. Use a lightweight padco applicator, 3/4" nap roller or squeegee to gauge material across surface achieving desired thickness

**Do not flip bucket upset down and allow to sit on surface

**Ensure you maintain a wet edge throughout application process

**Follow recommended coverage rates and wet film thickness

2. Create flow and movement using organic motions with preferred application tool

**Do not overwork material as color shift and blends will be more muted and muddy when using multiple colors

3. Allow coating to dry: 16-24 Hours @ 57F

8-12 Hours @ 75F

4.5 - 6 Hours @ 93F

**Do not force Dry

Recoat: 24 Hours @ 75F

**Surface should be abraded using 80-100 grit sanding screen to break surface tension, vacuumed, and solvent wiped with acetone to remove residual dust prior to applying final topcoat

• Light Traffic: 24 Hours @ 75F
• Heavy Traffic: 72 Hours @ 75F
• Equipment Traffic: 72 @ 75F

**Lower temps will further delay traffic time

MAINTENANCE

Inspect the installed floor by spot-cleaning and repairing any damaged or cracked areas as needed. To extend the life of the flooring system, implementing a daily maintenance program is strongly recommended to help ensure the floor remains safe for its intended use.

PRECAUTIONS 

• Refer to Safety Data Sheets (SDS) for safety precautions
• Safety precautions must be followed during storage, handling and use
• Personal Protective Equipment (PPE) shall be worn at all times of the application process including but not limited to long sleeve shirts, safety glasses, nitrile gloves and properly fitting NIOSH respirators
• All sources of ignition must be turned off and the area should be properly and adequately ventilated during both the application and curing processes
• The mixing area should be located on or near the project site and securely covered with plastic, cardboard or a tarp to protect against drips and spills
• Stage all materials, tools and cleaning supplies in a shaded area - out of direct sunlight - within the mixing area before beginning the application process
• Clean the mixing station and application tools after use with a VOC exempt solvent. Always follow all legal, health and safety guidelines when handling or storing solvents and materials, especially when working in confined spaces
• Dispose of empty packaging and other waste in accordance with all applicable federal, state, provincial and local regulations

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY  Floorguard Products® warrants that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine suitability of our product for your particular purpose. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER IFNORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

Beautiful Colors To Enhance Your Flooring Projects. Our Epoxy Pigment Is Sold In Quarts.  Easy To Use,  Just Pour And Blend with the HyperREZ UV Epoxy.  Add 6-7 Oz Per Mixed Gallon Of Pigment, Depending On Desired Color.  For A More Rich, Deeper Color, Add Up T0 10 Oz Of Pigment Per Mixed Gallon Of Epoxy.  Each 32 Oz Quart Colors 3-5 Gallons Of Floorguard Products Epoxy.