EZ-Coat Smooth Acrylic Coating | Metal, Wood, Concrete | Smooth Finish | Scratch Resistant

NON-Skid Properties

Meets ASTM C1028 for slip coefficient of friction and complies with ADA for slip resistance.

COVERAGE RATE: The coverage depends on the surface. Test the product on a small area of the substrate to estimate coverage Extremely porous surfaces may require multiple coats.

APPLICATION TEMPERATURE: 55°F-90°F with relative humidity below 80%

APPLICATION INSTRUCTIONS FOLLOW THESE SIMPLE APPLICATION STEPS

Precautions: Use material in a well-ventilated area. Protect the work of other trades. Protect shrubbery and other plants with drop cloths. Protect automobiles and all other areas not to be coated from overspray. Remove overspray from any windows, automobiles, metal, etc. as soon as possible should it occur. To prevent permanent staining, clean spills or leaks in a timely manner.

Temperatures should be above 50F and humidity below 80% for proper curing.

Store Materials in a well- protected area at 45-90F. Avoid freezing temperatures, direct sunlight & moisture. Keep away from heating sources.

Surface Preparation: Surface preparation is one of the most critical components before application of any product, but more specifically for floor coatings. All surfaces to be coated should be structurally sound, clean and dry. Failing wood boards should be removed or replaced. This includes wood rot, flaking or wood graining. Ensure all dust, debris, oil , grease, salts and other contaminants are free from the substrate  before application. All cracks and voids should be filled or patched. When applying over an existing coating, ensure the existing coating is deglossed and "dull" to improve adhesion. EZ-Bond will help with adhesion properties when needed. Our EasyClean Bio-Stripper is also ideal when existing coatings need to be completely removed.

Protect  the work of other trades. Protect shrubbery and other plants with drop cloths. Protect automobiles and all other areas not to be coated from overspray. Remove overspray from any windows, automobiles, metal, etc. as soon as possible. To prevent staining, clean spills or leaks in a timely manner.

Smooth Finish:

• We recommend applying using a 3/4 inch nap roller
• Two coats are recommended to achieve the desired dry film thickness (DFT) or at least 7-8 mils. Each coat is generally applied at a rate of 250-275 sq ft per gallon
• Allow for a sufficient drying in between coats. EZ-Coat should be dry to the touch before applying the second coat. At 75F 50% relative humidity this is approximately 1-2 hours
• Airless sprayers are recommended for the Smooth Version only ,if applying the texture, only use textured sprayers
• A 10-15% reduction with water is recommended for the first coat to "bite and penetrate porous substrates such as wood. DO NOT dilute when applying on metal or previously coated surfaces

Floor Application:

It is the duty of the applicator to ensure they are recommending the proper version to be used on a floor to avoid slip fall issues. We always recommend for floor applications to use our Textured Version to avoid slip fall hazards and improve traction of the coating. Depending on what the floors are being used for can be a factor and needs to be addressed by the applicator. RainguardPro will not be responsible for any accidents due to slipping or falling on the surface as it is the duty of the applicator to ensure it is the correct environment to be used in.

Concrete:

When applying on concrete, ensure the concrete is porous and able to rapidly absorb water. Concrete that is sealed or has an existing coating may affect long term adhesion. If concrete needs to bel lightly etched before application to open up the porosity due to a penetrating sealer, we would recommend our Restore-N-Prep product. Film-forming coatings should be addressed with a stripper to remove such as our Easy-Clean Bio-Stripper.

Ferrous Metal:

When applying direct to ferrous metal, always use a primer designed for this type of substrate as any water-based product can cause flash rusting.

Non-Ferrous Metal (Aluminum, Galvanized, Galvalume, Stainless Steel):

Remove all oils and coatings from the substrate via solvent wiping, IE SSPC-SP1. Etch or blast to create a 1-2 mil anchor profile or light etching before application. We recommend applying the EZ-Coat System within a few hours after scarification.

Dry Time: 

Test Panel: Always perform a test mockup to confirm acceptable conditions before proceeding with the general application. We recommend checking adhesion for proper results. When coating over existing coatings, ensure they are tightly adhered or removed before testing adhesion. EZ-Bond primer will improve adhesion to substrates and can be incorporated to improve the systems overall durability and adhesion performance.

Safe Handling: Use product only with adequate ventilation and/or an appropriate cartridge type respirator. Avoid contact with skin and wear protective gloves. Read the Safety Data Sheet before using.

Storage: Store materials in a well-protected area between 45° and 90°F. Avoid freezing temperatures, direct sunlight, and moisture. Keep away from heat sources.

Limitations:

• Substrate moisture content should not exceed 15%
• Always use the EZ-Bond primer on metal or previously coated substrates
• Not for use in submersible environments
• Do not apply in  below-grade settings without first priming with our Rubber-Lok membrane
• Do not apply on substrates with a pH exceeding 8
• Do not apply if rain is excepted within 24 hours of application
• Do not apply if temperatures are expected to drop below freezing within 24 hours of application

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.