ESD Cleaning Buffing Pads | Use with Eco Scrub Degreaser
Starting at $40.00
- Gray Scrub Pad provides great initial maintenance for light to moderate soiled floors
- Maroon Scrub Pad provides great maintenance for moderate to heavy soiled floors
- Use for both sides of scrub pad
- 1,500 square ft coverage
- Enhanced cleaning for ESD floor systems
Overview
- Description
- Additional Information
- More Options
ESD Cleaning Buffing Pads | Use with Eco Scrub Degreaser
ESD Gray and Maroon Scrubbing pads are used with the Eco Scrub Degreaser. These scrubbing pads allow for better maintenance on ESD floor systems along with the Eco Scrub degreaser.
The Gray Initial Scrub Pad is used for initial maintenance. Light – Moderate soiled floor and normal to moderate floor stripping.
The Maroon Deep Scrub Pad is used for continued maintenance. Moderate – heavy soiled floor and aggressive floor stripping / restoration.
Both scrubbing pass cover approximately 1,500 SF using both sides.
Why ESD Cleaning Buffing Pads?
- Gray Scrub Pad provides great initial maintenance for light to moderate soiled floors
- Maroon Scrub Pad provides great maintenance for moderate to heavy soiled floors
- Use for both sides of scrub pad
- 1,500 square ft coverage
- Enhanced cleaning for ESD floor systems
- Use with the Eco Scrub Degreaser.
| Weight | N/A |
|---|---|
| Dimensions | N/A |
| Size | |
| Surface Applied To | |
| Manufacturer | |
| Color | ESD Gray (Light – Moderate), ESD Maroon (Moderate – Heavy) |
-

CoatZF ESD Low-VOC Dissipative Clear Floor Finish | Static Control | ESD and Non-ESD Floors | 5 Gallon
- Zinc-free
- Static dissipative (1 x 10E6 to < 1 x 10E10 ohms) Coating - ANSI/ESD STM7.1 and ESD TR53
- Low tribocharging (<100 volts) coating - ANSI/ESD STM97.2
- 23% Solids- 2 Coat System** Reduces labor needed for initial install and on-going maintenance of the floor
- Hard, wear resistant – ASTM Standard D2134.93
-

GroundWorx Basics (SF) ESD Static Conductive Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014
- Water - based epoxy, matte finish
- Conductive range 2.5 x 104 - 3.5 x 107 ohms
- System Resistance (w/ ESD Footware) < 3.5 x 107 (fully compliant) ANSI/ESD STM 97.1
- Great low cost solution for concrete, wood, VCT Tile floors
- Extended working time - POT life 40+ minutes
-

GroundWorx Ultra (HB-97.2) ESD Static Conductive Epoxy Basecoat 100% Solids | Forklift Traffic | ANSI/ESD S20.20-2014
- Static dissipative or conductive high build epoxy electrical protection when used with the GroundWorx Ultra ESD Urethane Topcoat, which comes in either dissipative >1.0 x 10e6 ohms or conductive <1.0 x 10e6 ohms electrical resistance, limiting Static Charge Generation to <15 volts
- Great for high traffic, high wear commercial & industrial applications as high build 14 mil ESD system at <$4.00/sq' material cost
- Great for high traffic, high wear commercial & industrial applications
- Use on Concrete, Wood and old VCT surfaces
- Moisture tolerant primer
-

GroundWorx Ultra (HB-97.2) ESD Urethane Top Coat | Static Dissipative or Conductive | ANSI S20.20-2014
- Optional Static conductive <1.0 x 10e6 ohms or Dissipative >1.0 x 10e6 and <1.0 x 10e9 ohms high performance electrical protection, limiting Static Charge Generation to <15 volts
- Great for high traffic (forklift & pallet jack), high wear commercial & industrial applications with high build 14 mil system
- Conforms to ESDA, ANSI standard S20.20-2014 when used with the GroundWorx Ultra ESD Epoxy Primer
- Use on Concrete, Wood and old VCT surfaces
- Tough surface: impact resistance 140 psi and tabor abrasion test 25 mg loss
-

GroundWorx Basics (SF) ESD Static Dissipative Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014
- Water - based epoxy, matte finish
- Static Dissipative 10e6 - 10e9 ohms
- Great low cost solution for concrete, wood, VCT Tile floors
- Extended working time - 40+ minutes
- Quick turnaround - Light traffic 12 hours after application
-

GroundWorx Ultra Elevated Moisture Epoxy Primer | For Use In GroundWorx Ultra Epoxy Systems | Zero VOC | Recoat in 5 Hours
- Protects ESD Coatings System from moisture related issues (withstands up to 8lbs of moisture vapor pressure)
- Apply when relative humidity is up to 95%
- Significantly reduce chance of concrete outgassing
- Great for high traffic (forklift & pallet jack), high wear commercial & industrial applications
- Conforms to ESDA, ANSI standard S20.20-2014 when used with the GroundWorx Ultra ESD Epoxy Basecoat and the companion Ultra Urethane Toopcoat
-

ScrubWorx 20.20 ESD Floor Cleaner Concentrate
- Static Conductive
- High Activity Cleaner
- Micro-Cleans & Conditions
- Chemically Seals Tiles
- Simple to Use
You may also like…
-

CoatZF ESD Low-VOC Dissipative Clear Floor Finish | Static Control | ESD and Non-ESD Floors | 5 Gallon
- Zinc-free
- Static dissipative (1 x 10E6 to < 1 x 10E10 ohms) Coating - ANSI/ESD STM7.1 and ESD TR53
- Low tribocharging (<100 volts) coating - ANSI/ESD STM97.2
- 23% Solids- 2 Coat System** Reduces labor needed for initial install and on-going maintenance of the floor
- Hard, wear resistant – ASTM Standard D2134.93
-

GroundWorx Basics (SF) ESD Static Conductive Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014
- Water - based epoxy, matte finish
- Conductive range 2.5 x 104 - 3.5 x 107 ohms
- System Resistance (w/ ESD Footware) < 3.5 x 107 (fully compliant) ANSI/ESD STM 97.1
- Great low cost solution for concrete, wood, VCT Tile floors
- Extended working time - POT life 40+ minutes
-

GroundWorx Basics (SF) ESD Static Dissipative Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014
- Water - based epoxy, matte finish
- Static Dissipative 10e6 - 10e9 ohms
- Great low cost solution for concrete, wood, VCT Tile floors
- Extended working time - 40+ minutes
- Quick turnaround - Light traffic 12 hours after application


