E77 Fast Cure Epoxy Concrete Primer & Base Coat | 15 colors

COVERAGE RATE

RECOAT TIME

RECOAT TIME

Times will be longer for films thicker than 10 mils. For safety and proper product curing, good ventilation is necessary

when painting indoors or in confined areas. Be sure the batch numbers are all the same to provide uniform color. Epoxy

coatings may yellow or darken during application and after final cure. This will affect the color but will have no effect on

the performance of the product. Heaters that emit carbon dioxide and carbon monoxide can cause the coating to yellow.

MIXING AND APPLICATION INSTRUCTIONS

SURFACE PREPARATION

In all cases of surface preparation, the pH should be checked. A pH reading of 7.0 to 8.5 is acceptable. Also, a Water Dissipation Test should be made on random areas of the floor to determine if the proper degree of porosity has been achieved. Before the installation of our products, the substrate should be examined for moisture. Test for moisture vapor transmission using ASTM F-1869 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor using Anhydrous Calcium Chloride. The maximum allowable rate is 3 lbs per 1,000 sq feet per 24 hours. Test for relative humidity in concrete floor slabs using Probes according to ASTM F-2170. This test measures the presence relative humidity of the slab below the surface. The maximum relative humidity should be below 80%.

New concrete must be cured at least a minimum of 28 days before applying a coating. On-grade slabs must have moisture vapor barrier in place. All laitance, sealers, efflorescence, chemical contaminants, grease, oil and other foreign material must be removed. The prepared surface must be clean, dry and structurally sound. We recommend mechanical preparation by means of shot blasting or diamond grinding to achieve a CSP-2 or CSP-3 profile, in accordance with the International Concrete Repair Institute (ICRI). The profile should reflect something similar to a 60-100 grit sandpaper. If the substrate is not properly prepared and the appropriate

MIXING INSTRUCTIONS

E77 is prepared by mixing 1 Gallon Base .80 (Part A) to 1 Quart Hardener .20 (Part B) with an explosion proof variable speed drill and Jiffy mixer. E77 may be thinned up to 10% with Xylene. Overthinning reduces the high film build capability.

Roller - Use a 3/8” – ½” short nap phenolic core, shed resistant roller cover. Roll in the same direction always keeping a wet edge. Do not over roll product. Change out roller covers and mixing pails frequently to avoid build up of curing

material. Do not drain or scrape out mixing pails on floor. There can be un-mixed resin on sides of pails, which can cause soft spots on floor.

Brush - Use pure bristle brush. E77 is recommended only as a primer/base coat. Topcoat with a pigmented finish coat or a full flake broadcast. Do not apply if the temperature is within 5° of the Dew Point.

CAUTIONS

E77 is Flammable. Keep away from all sources of ignition during mixing, application and cure. The Hardener and Base can cause eye and skin burns as well as allergic reactions. Use goggles, fresh air masks or NIOSH approved

respirators, protective skin cream and protective clothing. This product is sold without warranty as to performance expressed or implied. Users are urged to make their own tests to determine the suitability for their particular conditions.

SEE MATERIAL SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS. FOR PROFESSIONAL AND INDUSTRIAL USE ONLY KEEP AWAY FROM CHILDREN. NOT FOR RESIDENTIAL USE NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY HARM.