E332 Polyester Polyurethane Coating| Clear | Topcoat | High Gloss | Chemical, Impact & Abrasion Resistant

Shelf LifeMinimum of 12 Months

COVERAGE RATE

Temperature       Tack Free       Minimum Recoat          Maximum Recoat         Foot Traffic             Traffic

90°F              1-1/2 Hours             6 Hours                         18 Hours                  18 Hours              48 Hours

75°F                   3 Hours              8 Hours                         24 Hours                  24 Hours              72 Hours

45°F                 16 Hours             24 Hours                        48 Hours                  48 Hours                5 Days

MIXING AND APPLICATION INSTRUCTIONS

MIXING INSTRUCTIONS

Stir each component to a uniform consistency.  Do not vary proportions.  E322 is prepared by mixing 2 parts BASE (Part A) to 1 part HARDENER  (Part B) with a slow speed explosion proof variable speed drill with a Jiffy mixer.  Be sure material is thoroughly mixed together. Do not thin E332.  Use as supplied.

Use of an improper drill mixer can result in streaking of the color because the pigment has not been thoroughly blended.  It can also create curing problems if the hardener also called activator (Part B) is not thoroughly blended with the resin (Part A) which can cause some areas on your floor to remain soft and not harden properly.  DO NOT USE A PAINT MIXER.  Many mixing problems described above can be traced back to using a paint mixer..  DO NOT HAND MIX as this approach can also result in the same problems as using a paint mixer.

APPLICATION PROCEDURE

E332 Clear Polyurethane is a top coat and is normally not recommended directly over unprimed surfaces. Apply over appropriate primers, intermediate coats or decorative floors. Surfaces must be free from all oil, grease, water or other foreign matter. Surface should be dry and above 45F and rising. Relative humidity should not exceed 85%. E332 is a moisture sensitive during application and initial cure. DO not apply if surface temperature is within 5 Degree of Dew Point. Not recommended on floors susceptible to hydrostatic pressure. Best methods of application are using lambs wool applicators or short nap rollers. E332 can be brushed by using pure Chinese bristle brushes.

For rolling, use a 1/4" - 3/8" shed resistant phenolic core cover. Roll in the same direction, always keeping a wet edge. Do not over roll product. For safety and proper curing, proper ventilation is necessary throughout application and cure. Any foodstuff and furnishings in the application area should be removed prior to application. When using pigmented Intermediate Coats, be sure the batch numbers are all the same to provide a uniform base color. E332 can be sprayed with an airless unit.

CAUTIONS

E332 is flammable.  Keep away from all sources of ignition during mixing, application and cure.  Contains Aliphatic Polyisocyanates, N-Butyl Acetate, Xylene and PM Acetate.  The HARDENER (Part B) and mixtures of BASE (Part A) with HARDENER (Part B) can cause eye and skin burns as well as allergic reactions.  The use of goggles, fresh air masks or NIOSH approved respirators, protective skin cream and protective clothing is a recommended standard practice when spraying. This product is sold without warranty as to performance expressed or implied.  Users are urged to make their own tests to determine the suitability for their particular conditions.

SEE SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS. KEEP AWAY FROM CHILDREN. NOT FOR RESIDENTIAL USE. FOR PROFESSIONAL AND INDUSTRIAL USE ONLY.

SEE MATERIAL SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.  FOR PROFESSIONAL AND INDUSTRIAL USE ONLY  KEEP AWAY FROM CHILDREN.  NOT FOR RESIDENTIAL USE NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY HARM.