E2.8 Poly-Chemcure Primer | Fast Recoat | Low-Temp | OEM/Steel Fabricator

COVERAGE RATE

CURE SCHEDULE

50% R.H. @ 2 MILS DFT @ 75°F                                               50% R.H. @ 2 MILS DFT @ 90°F          

• Dust Free . . . . . . . . 30 minutes ● Dust Free. . . . . . . . . . 35minutes
• To Touch . . . . . . . . 60 minutes ● To Touch . . . . . . . . . . 45 minutes
• Recoat. . . . . . . . . . . 105 minutes ● Recoat . . . . . . . . . . . . 60 minutes
• Hard Dry . . . . . . . . . 2.5 hours ● Hard Dry. . . . . . . . . . . 1.5 hours

• To Sand. . . . . . . . . . 5 hours ● To Sand. . . . . . . . . . .  4 hours
• Pack/Ship . . . . . . . . 4 hours ● Pack/Ship. . . . . . . . . . 3 hours
• Maximum Recoat. . . 7 days ● Maximum Recoat. . . . 5 days
• Pot Life. . . . . . . . . . . 5 hours ● Pot Life. . . . . . . . . . . . 2.5 hours

NOTE:

1. Dry times due to the colder temperatures and higher DFT are extended significantly.
2. Primer is susceptible to amine blushing at lower temperatures and high humidity.
3. Primer can be recoated in a minimum of 16 hours at 35°F and 48 hours @ 20°F.
4. If you cannot recoat within 7 days, a light sanding with 220-320 grit open coat sandpaper must be done to assure proper topcoat adhesion.

Times will be longer for thickness above 2 mils DFT.  For maximum recoat times contact Gulf Coast Paint Mfg., Inc.   For safety and proper product curing, good ventilation is necessary when painting indoors or in confined areas.  Epoxy coatings may yellow or darken during application and after final cure.  PC-2.8 Hardener will darken with age.  This will affect the color but will have no effect on the performance of the product.  Heaters that emit carbon dioxide and carbon monoxide can cause the primer to yellow.  PC-2.8 is designed as a primer; use appropriate topcoats.

.

MIXING AND APPLICATION INSTRUCTIONS

SURFACE PREPARATION

1. Steel

a. Sandblast (Recommended) 

Sandblast to a "commercial" (SSPC-SP6) or "Near White" (SSPC-SP10) blast finish. For best results, prime the same day with E-2.8 Epoxy Primer

b. Power Tool Clean

Follow instructions as outlined in SSPC-SP3 specification

c. Hand Cleaning 

Follow instructions as outlined in SSPC-SP2 specification

2. Galvanized Steel/ Aluminum

Solvent clean per SSPC-SP1 or steam clean. Sweep blast to achieve a minimum 1 mil profile

3. Previously Painted Surfaces 

Solvent clean per SSPC-SP1 and/or power wash. Remove loose existing paint by wire brush or other hand tools. Feather edges. Make test application to check for combability.

MIXING INSTRUCTIONS

Stir each component to a uniform consistency, using an explosion proof variable speed drill with an appropriate size Jiffy Mixer®.  Make sure any pigment settled to the bottom is incorporated.   DO NOT vary proportions.  PC-2.8 is prepared by mixing 2 parts Base (Part A) to 1 part Hardener (Part B) with a Jiffy Mixer® Power Mixer.  PC-2.8 may be thinned up to 15% with SA-65 Thinner.

V.O.C.

Unthinned                       Thinned 5%                           Thinned 10%                    Thinned 15%

2.8 lbs./gl.                        3.0 lbs./gl.                               3.18 lbs./gl.                      3.35 lbs./gl.

(335 gms./liter)                 (359 gms./liter)                        (381 gms./liter)                 (401 gms./liter)

CONVENTIONAL SPRAY                                                            AIRLESS SPRAY

Spray Gun:  Binks 2001 – DeVilbiss JGA                                          Pump:  Graco Extreme 33:1

Fluid Nozzle:  Binks 63CSS – DeVilbiss FF (1.4) 1.0-1.7                    Airless Gun:  Graco 207945

Air Cap:  Binks 63PR  DeVilbiss 765                                                 Fluid Hose:  3/8” x 50’ Max.

Tips:  415-519

Min. pressure to avoid fingering: 2700                                                                                                     psi min.

When spraying, use a 50% overlapping crosshatch pattern to maximize hide and minimize the occurrence of pinholes.  Do not apply to surfaces below 35°F or above 120°F.  Do not apply over dew or frost.  The surface temperature should be at least 5°F above the dew point.  Manufacturers listed above are a guide.  Others may be used.  Changes in pressure and tip size may be required to achieve proper application.

CAUTIONS

E2.8 is Flammable.  Keep away from all sources of ignition during mixing, application and cure.  The Hardener (Part B) is corrosive and can cause eye and skin irritation as well as allergic reactions.  The use of goggles, fresh air masks or NIOSH approved respirators, protective skin cream and protective clothing is recommended standard practice when spraying coatings.  Proper ventilation is always required.

This product is sold without warranty as to performance expressed or implied.  Users are urged to make their own tests to determine the suitability for their particular conditions.

SEE MATERIAL SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.  FOR PROFESSIONAL AND INDUSTRIAL USE ONLY  KEEP AWAY FROM CHILDREN.  NOT FOR RESIDENTIAL USE NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE SAFETY DATA SHEET AND FOLLOW THE PRECAUTIONS TO PREVENT BODILY HARM.