E10 Floor & Deck 100% Acrylic Coating | 22 Colors | Concrete, Masonry, Wood | Quick Dry | Satin Sheen | UV Resistant

COVERAGE RATE

Coverage will vary depending on the surface applied to.

Smooth Surfaces: Up to 300 Square Feet Per Gallon

Rough Surfaces: 125-250 Square Feet Per Gallon

APPLICATION TEMPERATURE: Not recommended for application when the temperature is below 55°F. Rain may damage uncured products. If inclement weather threatens, cover the deck to protect new application. Do not allow any non-applied product to freeze.

APPLICATION INSTRUCTIONS FOLLOW THESE SIMPLE APPLICATION STEPS

Surface Preparation:

LIMITATIONS

• Do not install any product if the temperature is below 55°F.
• Rain may damage uncured products. If inclement weather threatens, cover deck to protect new application.
• Do not allow any non-applied product to FREEZE.
• DO NOT PAINT OVER MILDEW. Mildew is a fungus, brown, black, grey or even white in color, and will rapidly grow through any
  coating applied over it. A solution of 50% household bleach and 50% water will kill the mildew. Rinse thoroughly. See precautions
  on bleach label for handling before using.

Concrete, concrete decks, floors and walk ways New concrete must age for a minimum of 30 days. Cool temperatures and high humidity may require a longer cure time.

Remove all grease, oil and wax with T. S. P. Solution. (One pound of T. S. P. to 1 gallon of water.) Scrub with stiff broom until surface is thoroughly clean. Rinse thoroughly with clear water. Power wash all concrete with 3000 lb. pressure washer, spray tip should be no further than 6” from concrete surface. A properly etched concrete surface should resemble the texture of fine or medium sandpaper.Prepare surface to achieve a CSP of 2 to 4 as per ICRI Guideline 310.2 R-2013 Let dry thoroughly before applying coating.

For Interior and/or Hard Troweled Cement:

Need to rough up smooth concrete surfaces using one of two methods below.

CHEMICAL ETCHING METHOD:  For an acid etch preparation we suggest our E760CE Muriatic Replacement as a safer alternative.  Power wash surface after minimum 10 minutes or more but before dry to neutralize the E760CE,  then let water thoroughly dry and apply coating.  If no power wash available, can wet mop or hose off but will need to run a stiff broom over surface while wet with E760CE to agitate before neutralizing.

MECHANICAL ETCHING METHOD: Use a grinder or bead blaster with a dust filter, or vacuum attachment, evenly over the surface. A small hand grinder may need to be used where horizontal meets vertical substrates. Rinse thoroughly using a pressure washer to remove all remaining dust and residue. A properly etched concrete surface should resemble the texture of fine or medium sandpaper. Let dry thoroughly before applying coating.

Mildew: DO NOT PAINT OVER MILDEW. Mildew is a fungus, brown, black, grey or even white in color, and will rapidly grow through any coating applied over it. A solution of 50% household bleach and 50% water will kill the mildew. Rinse thoroughly. See precautions on bleach label for handling before using.

Glossy Surfaces: Roughen gloss by sanding; then wash with a T.S.P. solution and rinse thoroughly with water.

Previously Painted Surfaces: Clean all surfaces and roughen all glossy surfaces by sanding. Clean all surfaces thoroughly with a T.S.P solution and then rinse thoroughly with water. Do not paint over loose or peeling paint.

Unpainted Surfaces: For maximum durability, prime all surfaces to be coated. Caulk all cracks and nail holes.

Wood: Clean and primer all new wood with E1575 Primer. Coat with 1-2 thin coats of E28 Series.
Metal: Clean and etch all new metal. Prime all bare metal with E1575 or E7075 primer.

Weather: Do not install any product if the temperature is below 55. Rain may damage uncured products. If inclement weather threatens, cover deck to protect new application. Do not allow any non-applied product to FREEZE.

Priming: For best results and when necessary as specified, prime surfaces with this product (25 Series) thinned with one quart of water before applying the top coat.

Application:

Box and mix all containers to insure consistent color. Neatly cut-in all edges with a brush and roll the main area using a 1/2” to 3/4” nap, good quality roller cover. Be sure to spread evenly in a “V” pattern, rolling in both directions. It is best not to apply this product in the direct sun at temperatures above 80°F. Thinning slightly with water and applying thin coats will help avoid streaks when working in direct sun. (See specifications for more application details).

Application can be done with brush, roller or sprayer.  For roller application suggest 1/2″ nap roller cover on smooth surfaces and a heavy duty 3/4″ nap on rough surfaces.  When applying with an airless sprayer suggest a .017 orifice spray tip in a 5-17 configuration.

Dry Time: Allow six (6) hours between coats and light foot traffic. Normal foot traffic after 24 hours. Allow 48 hours before placing heavy objects on the surface. Cool temperatures and high humidity may require a longer cure time.

Maintenance:  See the E10 Maintenance Sheet in the Document Library

MAINTENANCE:

• Clean up spilled and undried product immediately with water.
• Clean hands and skin with warm water and soap.
• Most Stains will clean-up with TSP, a brush, and water. We recommend a re-coat every 2-5 years, depending on traffic and exposure
  to the sun.

NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.

What is the E10 Floor & Deck Coating?

The E10 100% Acrylic Sealer Floor & Deck Coating is a fast-drying, water-based acrylic coating designed for concrete, masonry, and wood surfaces. It provides a durable satin sheen finish with excellent UV resistance, color retention, and resistance to water, alkalis, acids, and staining. It is available in 22 color options for residential and commercial applications.

What surfaces can E10 be used on?

E10 is designed for a wide range of surfaces including:

• Concrete patios
• Pool decks
• Walking roof decks
• Wood decks
• Concrete and wood floors
• Masonry surfaces
• Fiberglass mat waterproof deck systems
• Texture concrete overlay systems

This makes it a versatile deck and floor coating a variety of projects.

Is E10 good for decks and patios?

Yes. E10 is specifically designed for decks, patios, and outdoor living spaces. Its UV-resistant acrylic formula helps protect surfaces from weathering and fading while maintaining long-lasting color. The satin sheen finish gives surfaces a clean, updated appearance without an overly glossy look.

What is the difference between E10 and E28 Cool Life Deck Coating?

E10 is a more cost-effective acrylic deck coating option that offers many of the same protective and decorative benefits as the E28 system, including the same color selections. However, E10 does not include the heat-reducing or cooling technology found in the E28 Cool Life Deck system.

E10 is an excellent choice for customers who want:

• A decorative deck coating
• Fast drying performance
• Strong UV protection
• Multiple color options
• A budget-friendly alternative to cool deck coatings

How many color options are available for E10?

E10 is available in 22 colors, including popular earth tones, grays, reds, blues, and tans.

Popular choices include:

• Sandstone
• Arizona Tan
• Concrete Gray
• Tile Red
• Skate Blue
• Spanish Brown
• Sandy Beige

The large color selection makes it easy to match pool decks, patios, porches, walkways, and outdoor entertaining spaces.

Does E10 help protect against sun damage and fading?

Yes. E10 is formulated with excellent UV resistance and color retention to help protect coated surfaces from fading and weather damage caused by sun exposure.

Is E10 water resistant?

Yes. E10 is resistant to ponding water, moisture, alkalis, acids, and staining. This makes it a strong option for pool decks, patios, walkways, and outdoor concrete surfaces exposed to weather and moisture.

Is E10 easy to apply?

Yes. E10 can be applied using:

• Roller
• Brush
• Airless sprayer

The product is water-based with easy soap-and-water cleanup.

Does E10 require a primer?

For unpainted surfaces, the website recommends using the E25 Primer for best adhesion and durability. Proper surface preparation is important before coating concrete, masonry, or wood surfaces.

Can E10 be used around pools?

Yes. E10 is commonly used on pool decks and outdoor concrete surfaces because it is UV resistant, moisture resistant, and durable against outdoor exposure. Its satin finish also provides an attractive decorative appearance for pool areas.

Is E10 environmentally friendly?

E10 is a low VOC, water-based acrylic coating designed with easier cleanup and lower odor compared to many solvent-based coatings.

How long does E10 last?

Longevity depends on traffic levels, weather exposure, and maintenance. The maintenance section recommends recoating every 2–5 years depending on exposure and wear.

What makes acrylic deck coatings popular for outdoor surfaces?

Acrylic deck coatings are popular because they offer:

• Fast drying times
• UV resistance
• Decorative color options
• Easier application
• Good outdoor durability

Outdoor concrete coatings with acrylic technology are commonly chosen for patios, pool decks, porches, and walkways because they balance appearance, protection, and maintenance.