Bio-Seal E192 Epoxy Sealer | Repair, Reinforce & Mortar Resin | Wet Surface Resin / Fiberglass

CURE SCHEDULE

APPLICATION TEMPERATURE: 45- 110 degrees F

Product Use Instructions 

Surface Preparation

Bare Concrete: Surfaces should be allowed to cure for a minimum of 20 days before coating. Excessive weak surface laitance must be removed by either acid etching or, preferably, abrasive sweeping before coating. Aged, uncoated concrete surfaces are best prepared by abrasive sweeping. Unless carried out properly acid etching can give unpredictable results due to inadequate etching or inadequate rinsing, for this reason abrasive blasting is the preferred method of preparation. Contamination by oil or grease should be removed, with an industrial degreaser before abrasive blasting or acid etching.

Mixing Procedures

Bio-Seal E192 is supplied in 2 gallon kits of comprising epoxy base in a part filled 2 gallon plastic pail with curing agent packed in a part filled one gallon steel can. A "Jiffy" type mixer with a high torque motor is recommended for proper blending. Pour the curing agent into the base and mix for about 2 minutes taking care to stir in all base material from the edges and base of the plastic pail, unmixed material will never harden. No induction or "sweat-in" time is required and the mixed material may be used immediately.

When using with sand or other inert mineral aggregate as a mortar first thoroughly mix a two-gallon BIO-SEAL E192 kit using a 1/2" "Jiffy" type mixer then pour this mixed material into a larger container such as a clean five gallon pail. Using the same Jiffy mixer add the desired mineral aggregate while stirring until the desired viscosity is obtained. As a guide it will be found that a two-gallon kit of BIO-SEAL E192 will accept about 66 lbs of sand to yield five gallons of a heavy but flowable mortar. This mortar can be used to smooth and level concrete, set safety railings into holes and so on. Addition of more sand will yield a stiffer mortar, which can be applied in heavy thickness without sagging. Fine sand makes a stiffer mortar than coarse sand. Sharp sand makes a stiffer mortar than rounded sand.

Pot life and reaction time is heavily dependent on temperature, as a general guide figure that each 18°F, (10°C), variation in

temperature above or below 77°F, (25°C), will respectively halve or double the pot life and cure times.

Application 

Brush or roller application is straightforward and requires no special technique. Application on a floor is assisted by using as squeegee to distribute the Bio-Seal E192 then back rolling to achieve an even coating. The material will thicken in cold weather and will be noticeably heavier at temperatures of 50F and below. If permissible to use solvent it will be found that 5-10% of lacquer thinner or MEK will greatly reduce viscosity in cold weather allowing much easier application.

Once applied to wet surface, product can be submerged and cured under water. NOTE-  product cannot sustain wave movement until fully cured!

CURING BEFORE SERVICE: BIO-SEAL™ 192 will cure to a hard film within 24 hours and is suitable for traffic after this time. Allow at least three (3) days at 77°F before subjecting to aggressive chemical service from industrial solvents and similar materials.

TYPICAL PROPERTIES OF CURED BIO-SEAL 192:

Compressive Strength: 10,000+psi

Tensile Strength: 7,000+ psi

Tensile Elongation, (Flexibility): 3.2%

Hardness (Shore D): 78

Glass Transition Temp: 122’F

Safety: This is a hazardous material if misused. Read and understand the Safety Data Sheets (SDS's) before use

Warranty Disclaimer: The technical data given herein has been compiled for your help and guidance. It is based upon our experience and knowledge however, as we have no control over the use to which this information is put, no warranty, express or implied, is intended or given. We assume no responsibility whatsoever for coverage, performance, or damages, including injuries resulting from use of this information or products recommended herein.

Check out customer projects using the Bio-Seal E192!