10x Polyurea Interior Control Joint Filler | Quick Cure | Cold Temperature Apply Down To 0F

Considerations:

• Do not store product in direct sunlight
• Surfaces must be dry and without contaminants
• Application Temperature 0-120F with a maximum allowed concrete moisture content of 5% (ASTM 2659 testing)
• Due to quick cure rate and dry time it’s suggested to thoroughly evaluate the product before using

Product Limitations:

• Colors or gloss may be affected by high humidity, low temperatures, chemical exposure or exposure to lighting such as sodium vapor lights
• Do not install in control joints or cracks where moisture is present
• Do not expose this product to water until fully cured
• Substrate temperature must be 5F above dew point
• All new concrete must be cured for at least 30 days, ideally a slab is recommended tocure 60-90 days
• Physical properties are typical values and not specifications
• Do not install outdoors due to thermal cycling movement
• Always apply a test patch to determine product suitability and adhesin performance for your proposed application method and procedures. Product is NOT UV Stable may discolor due to UV exposure

APPLICATION INSTRUCTIONS

Joint Preparation: To assure a trouble-free bond, all dust, oil, dirt, foreign contaminants and laitance must be removed. It is imperative that there is no moisture present when filling the joints, moisture can cause the 10X to bubble and not bond properly. Use a vacuum attached saw with a diamond blade that will reach the base of the joint, removing any sealers, curing compounds or debris. Only use backer rod when joints are exceeding 2″ inches in depth.

Product Storage: Product must be stored in an area that will bring the product to room temperature prior to using. Continuous storage should be between 60 and 80 degree F. Keep from freezing, and do not store in hot environments such as inside of a truck or trailer, allowing the product to get hot.

Product Mixing: Shake cartridges vigorously fir 1-2 minutes prior to use. When using 10X in buckets, pre-mix , the Part A and Part B with a drill mixer for 1-2 minutes each using a slow speed mixer.

IMPORTANT

MIXING ORDER – Jiffy Mixer and Drill Motor Mixing Part A must be in the mixing pail first and the jiffy mixer MUST be moving and mixing the part WHILE the equal amount of Part B is evenly poured into the moving part A. DO NOT reverse this mixing order. Once Part B has been added to the moving Part A, mix the A & B at full speed, moving the Jiffy mixer up, down and around the mixing pail. Mix for no more than 60 seconds, then pour into application IMMEDIATELY —DO NOT WAIT.

Improper mixing may result in product failure.

For best mixing results and proper blending of parts A and B, recommend a Jiffy Mixer style drill mixer.

Product Application: Once the cartridge has been shaken, remove the nut from the cartridge and save it for further use. If a partial cartridge is used, the nut can be used to seal the cartridge head. Screw on the mixing tip, then insert the catrrtirdge into a dual comonent mixing gun. Hold the gun vertically, with the mixing tip pointed up, and start triggering the mixing gun so the product starts filling the mixing tip. Then take the mixing gun and point it to the ground, slowly discarding about 1 oz of product. when using a dual feed power pump, make sure the lines and dispensing manifolds are clean and the lines are clear from previous use.

When using the mixing gun, be consistent with the pressure and speed when pressing the trigger. Inconsistent pressure can cause the product to dispense unevenly and therefore won’t be mixed properly. When this happens, you may have spots in the joints that don’t cure because of not being mixed properly during dispensing. When using a partial cartridge, the mixing tip cannot be used for further application, it will have cured material inside of the tip. It is recommended to have extra mixing tips on hand.

Joints that are 1″ or less in depth can be filled in one pass. If the joints are deeper than 1″ , must be filled in 2 passes, fill the bottom half first, then follow up with filling the top half in the second pass. Overfill the joints slightly, making sure not to trap air bubbles. If there are low spots in the joints, or the 10X is not flush with the floor, abrade the 10X and reapply. The 10X will cure fast, once it’s cured, scrape the joints flush. Make sure you are using a scraper that has a sharp blade, using a dull blade will make it more difficult to scrape.

Cleanup and Restrictions:

Clean metal tools with a solvent, such as xylene or MEK. Cured material may be disposed of with no restrictions. Never discard and throw out uncured Part A or Part B. Mix them together to cure them, then discard.

Considerations:

• Do not store product in direct sunlight
• Surfaces must be dry and without contaminants
• Application Temperature 0-120F with a maximum allowed concrete moisture content of 5% (ASTM 2659 testing)
• Due to quick cure rate and dry time it’s suggested to thoroughly evaluate the product before using

Warranty: Floorguard Products warrants that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine suitability of our product for your particular purpose. Listed physical properties are typical and should not be construed as specifications. NO WARRNATY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESUTLS YOU WILL OBTAIN FORM OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We SHALL HAVE NO LIABILITY FOR INCDENTAL OR CONSEQUENTLA DAMAGE, DIRECT OR INDIRECT. Our LIABILITY IS LIMITED TO THE NET SELLING PRICE OF OUR PRODUCT OR THE REPLACEMENT OF OUR PRODUCT, AT OUR OPTION. ACCEPTANCE OF DLIEVERY OF OUR PRODUCT MEANS THAT YOU HAVE ACCEPTED THE TERMS OF THIS WARRANTY WHETHER OR NOT PURCHASE ORDERS OR OTHER DOCUEMTN STATE TERMS THAT VARY FROM THIS WARRANTY.  No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any salfe of our products. Our products contain chemicals that may  CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.