Call us (630) 675-4509
Show
Filter by
Filter by
6007 Wet Condition Epoxy For Concrete & Steel | Low Temp 35°F
From: $593.00- Protect Problem Wet and Damp Areas
- Withstands to 20 PSI Hydralic Vapor Pressure
- Cold temperature down to 35°F
- Designed to Protect both Concrete and Steel
- Use as Primer With Topcoat or Floor Coating
- Offers Excelllent Moisture and Corrosive Protection with Outstanding Adhesion
- 100% Solids, no VOC, 2 Component
Hot
6009 Epoxy Floor Coating Industrial & Commercial Low Temp 35°F | 100% Solids | Quick Cure
From: $115.00- Commercial, Industrial, Residential Concrete Floors
- Cold temperature down to 35°F
- Tough - Attractive Looking Epoxy
- Good Chemical, Abrasion, Impact Resistance
- Quick 4 to 7 hour set time
- Self Priming With No Primer Required
- 100% Solids, no VOC, 2 Component
- Clear or Selection of Colors
- Excellent Protection at Lower Cost
AM1016 Anti-Microbial Mildew Resistant Anti-Slip Epoxy Floor Coating – 3 Gal Kit
From: $210.00- Adds slip resistant finish to concrete floors
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Good for surfaces subject to bare foot traffic
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical and abrasion resistance
- Wide selection clear plus 20 colors
- Water base
AM253 Novolac Anti-Microbial Epoxy Resists Mildew Growth Acid Solvent Chemicals
From: $398.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Resists high concentration acids, some chlorinated solvents incl xylene, MEK
- High build for heavy duty traffic, chemical troughs, curbs
- Great for tanks, chemical spill areas
- Works on cement, masonry or brick
- Excellent adhesion 425 psi
- Quick back in-service, light foot traffic 10-18 hrs
- Low voc 47 g/L
AM257P Novolac Primer Anti-Microbial Epoxy Resists Mildew Growth Acid Solvent Chemicals
From: $325.52- Outstanding Spill & Splash Acid, Solvent, Chemical surface protection
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Excellent primer companion to AM253 Novolac Anti-Microbial Epoxy
- Resists wide range of chemicals, solvents, acids
- Excellent adhesion 375 psi
- Long working time 1 to 3 hour POT life
- Selection of 3 color options
AM5015 Anti-Microbial Mildew Resistant Epoxy Primer WB
From: $94.00- Versatile epoxy primer for concrete, masonry, wood
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Available 20 Colors To Match Topcoat
- Excellent primer for epoxy, polyaspartic, urethane
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical & abrasion resistance
- Water base
AM707HB Anti-Microbial Mildew Resistant Epoxy Floor Coating | 100% Solids
From: $162.00- High Build - 100% Solids Commercial Epoxy
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Long POT Life (working time) 30-50 min
- Excellent Adhesion 450 psi
- Abrasion resistant Only 32 mg loss (Tabor test)
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
- Wide Variety of 20 Different Colors
Deep Ice Countertop and Casting Epoxy | River Tables | Bar Tops | To 4″ Deep | Bubble Free
From: $85.00- Easy Application
- No need to use torches or vacuum chambers
- Bubble Free
- See-through clarity
- Looks great with Metallic and Mica pigments and Dyes
- Can be poured up to 4” thick at one time
- Excellent UV & Chemical Resistance
- Superior Structural Strength: Withstands 2,000 lbs/sq.in pressure for up to (30 minutes of exposure)
DT-454 Epoxy Quick Cure UV Concrete Floor Coating Low Temp 40F | 100% Solids
From: $70.00- Tough, Durable Epoxy Coating
- Quick cure 6-7 hour recoat time
- Outstanding Bonding
- UV Resistant
- Good chemical, impact and abrasion resistance
- Cold temperature application down to 40F
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 14 colors! (Pigment sold separately)
E1000 Epoxy Concrete Repair Kit | Holes to 1″ | Cracks | Spall | 3 Color
$136.00- Make quick, permanent repairs to concrete
- Patch cracks, spalled concrete and potholes
- Can be applied at ¼” – 1” thickness
- Outstanding adhesion to concrete
- Excellent chemical, abrasion and impact resistance
- USDA approved for food processing plants
- Easy to mix and apply
- 3 Colors Packaged in a 5 gallon pailConcret
E100V Vertical Wall High Build Epoxy Coating | Underwater Concrete | Pools | 13 Colors
From: $50.00- No sagging on vertical walls to 12 mils per coat
- Works well on underwater concrete decorative surfaces
- Great for pools and water features
- Good chemical and abrasion resistance
- Long 45 - 90 min pot life
- Outstanding adhesion 475 psi @elcometer
- Comes in 5 color options
- 100% solids, very low voc
E1015V Vertical Wall Epoxy Coating & Primer to 8 Mils No Sag | 11 Colors
From: $50.00- No sagging on vertical walls up to 8 mils per coat
- Good for priming or coating concrete, wood or masonry.
- Good chemical and abrasion resistance
- Long 1 - 1.5 hour pot life
- Excellent adhesion 425 psi @elcometer
- Wide selection of 11 color options
- Water base
E1016 Anti-Slip Epoxy Concrete Floor Coating – 3 Gal Kit
From: $196.00- Adds a slip resistant finish to concrete floors
- Good for use on surfaces subject to bare foot traffic
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical and abrasion resistance
- Wide selection of clear plus 20 color options
- Water base
E105M Epoxy Mortar Concrete Resurfacer & Patch Kit
From: $66.00- Economical Easy resurfacing old and damaged concrete floors
- Compressive Strength 8,400 psi ASTM D695
- Heat Deflection Temp 131.7F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- 100% solids epoxy
- Comes complete with epoxy & aggregate
- Selection of 5 color options
- Application temp range 55°F to 90°F
E110M Epoxy Mortar Concrete Premium Resurfacer & Patch Kit
From: $73.00- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- 10% greater coverage/unit vs E105M Epoxy Mortar
- Compressive Strength 11,150 psi ASTM D695
- Heat Deflection Temp 158.9F ASTM D648
- High Build Resurfacing 1/8" to 1"
- Spot Patching up to 2" - 3" thick
- Long 30-40 min POT Life
- 100% solids epoxy
- Comes complete with epoxy and aggregate
- Selection of 5 color options
- Application temp range 55°F to 90°F
E126CW Cold Weather Epoxy Mortar Concrete Resurfacer & Patch Kit 35°F to 80°F
From: $71.00- Great for Cold Weather & Cold Storage Facilities
- Application range 35°F to 80°F
- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- Compressive Strength 11,284 psi ASTM D695
- Heat Deflection Temp 149.9F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- 100% solids epoxy
- Comes complete with epoxy and aggregate
- Selection of 5 color option
E128AF Arctic Epoxy Mortar Concrete Patch Kit | Cold Condition -10°F to 40°F
From: $70.00- Tough, Durable Cold Winter Weather Concrete Patch & Repair
- Excellent Extreme Cold Condition Patching -10°F to 40°F
- Great For Freezer, Cold Storage and Outdoor Winter Repairs
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- Excellent chemical resistance
- Excellent Abrasion and Impact Resistance
- Compressive Strength 11,000 psi ASTM D695
- Quick recoat 1-2 hrs & 2-4 hrs light foot traffic
- Selection of 3 color options
- Easy to Use 3 part kit Includes Silica Sand or Liquid Only
E130A Oil Contaminated Concrete & Asphalt Epoxy Mortar Patch Kit/Resurfacer
From: $66.00- Great for patching and repairing oil contaminated and damaged concrete
- Can be used to patch and repair asphalt surfaces
- Can be applied up to 1/8" one application
- Crack. holes and general surface repairs
- Excellent abrasion and impact resistance
- 100% solids
- Easy to Use 3 part kit Includes Silica Sand or Liquid Only
E139FL Flexible Epoxy Primer & Floor Coating | 60% Elongation | 100% Solids | Indoor & Out...
From: $65.00- Exceptionally flexible epoxy with 60% elongation
- High Build up to 50 mils thick per coat
- 100% Solids Commercial Epoxy
- Excellent Adhesion 450 psi
- Tough Abrasion resistant Only 6 mg loss (Tabor test) and 160 inch lbs Gardner variable impact test
- For use with broadcast systems and as flexible membrane primer
- Wide Variety of 15 Colors
E1409CL Moisture Vapor Barrier Epoxy Sealer Primer For Concrete ASTM F3010
From: $247.00- Reduce effects of moisture vapor transmission on concrete floors
- Control moisture vapor emission rates to 20 lb/24hr/1000 sq' (ASTM F1869)
- Used as Sealer/Primer to protect Polymeric coating systems, vinyl sheets, tile, cementitious overlays, terrazo, wood veneers, and carpet
- 100% solids with 0 voc
- Easy to apply with one coat most projects
- Meets ASTM F3010 for vapor permeance at the recommended thickness
E1500HN Novolac Epoxy | Superior Steel & Concrete Chemical Horizontal Protection | Secondary Co...
$340.00- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
- Great horizontal chemical protection for Secondary Containment for both steel and concrete surfaces
- Thin film self leveling to 40 mils DFT one coat
- Extremely tough with high wearing properties
- Excellent abrasion resistance and impact resistance
- Meets USDA requirements
E15M Epoxy Mastic Steel Primer DTM & Concrete Coating | Chemical Resistant | Low Temp 25F
From: $95.00- High solids DTM (direct-to-metal) chemical resistant steel primer or finish coat to steel and concrete
- Self priming to steel including tight rust
- Apply Vertical Surfaces to 8 mils DFT Steel & Concrete
- Great primer for use with our E1500HN (horizontal) and E555VN (vertical) Novolac Chemical Resistant Epoxies
- USDA Approved
- Tight film, low permeability.
- Exceptional adhesion Exceeds 500 psi
- Excellent impact resistance 90 in lb
- Excellent abrasion resistance CS 17 Wheel, 1000 cycles, 1000 g Load 21 mg loss
- Excellent against rust “undercutting”
- Easy to apply brush, roll and spray
- Low temp cure version to 25°F
- Available 13 colors
E183HB Epoxy Floor Coating High Build | Quick Back In-Service | Abrasion & Chemical Resistant |...
From: $324.00- High Build - Impact & Chemical Resistant
- Quick back in-service light foot traffic 8-14 hrs
- Full chemical resistance only 3 days
- Excellent Adhesion 450 psi
- Abrasion resistant Only 23 mg loss (Tabor test)
- Excellent Chemical Resistance
- High build apply 10 to 20 mils one coat (80 - 160 sq'/gal)
- Wide Variety of 19 Different Colors
E5013 Fast Set Clear Epoxy Primer WB Concrete | Wood | Masonry
From: $60.00- Versatile product good on concrete, masonry, wood surfaces
- Quick 4-6 hour Recoat for same day projects
- Excellent as clear primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Long 2 hour pot life
- Excellent adhesion 425 psi
- Good chemical and abrasion resistance
- Water base
E5015 Epoxy Primer WB Coating | Concrete Wood Masonry | 20 Colors
From: $51.00- Versatile product good on concrete, masonry, wood surfaces
- Excellent as primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Available in Clear and 20 Colors To Match With Topcoat
- Long 1 - 1.5 hour pot life
- Excellent adhesion 425 psi
- Good chemical and abrasion resistance
- Water base
E505V Vertical Wall Epoxy Concrete Block Filler to 20 Mils No Sag | 11 Colors
From: $117.00- No sagging on vertical concrete and cement block walls up to 20 mils per coat
- Great epoxy block filler
- Good chemical and abrasion resistance
- Long 45 - 90 min pot life
- Excellent adhesion 420 psi @elcometer
- Wide selection of 11 color options
- 100% solids, very low voc
E517M Flake Filled Epoxy Mastic Steel & Concrete Coating | Chemical Containment | Low Temp 25F
From: $125.00- Self Priming on steel
- Excellent primary containment coating for internal tank linings (when part of specified system)
- Excellent secondary containment coating
- Performs well over epoxy mortars and properly primed concrete surfaces
- Can be applied on damp surfaces
- Excellent chemical resistance to acids, caustics, solvents
- Outstanding impact and abrasion resistance.
- Exceptional adhesion Exceeds 700 psi
- Excellent flexibility pass 7/8" mandrel 180º Bend
- Apply Vertical Surfaces to 15 mils one coat
- Meets USDA requirements.
- Low temp cure version to 25°F
- Low VOC 72 grams/Liter
E555VN Novolac Epoxy | Superior Steel & Concrete Chemical Vertical Protection | Tank Linings
$142.00- Excellent resistance to acids, alkalis, salts, most industrial chemicals and many solvents
- For Use in tough corrosive chemical environments including 98% Sulfuric Acid, 37% HCL and 70% Sodium Hydroxide
- Vertical application to 10 mils DFT.
- Great for Secondary Containment for both steel and concrete surfaces
- Use as Primary Containment and Tank Linings when used as part of specified system
- Excellent abrasion resistance with ceramic filler
- Excellent in battery storage room areas.
- Meets USDA requirements
- May be applied in cold, damp conditions to 45°F with curing down to 35°F
E572500 Non-Slip Skidproofer High Performance Epoxy Coating
From: $131.00- Great protection for problem slippery or wet concrete areas
- Outstanding slip resistance with a very aggressive textured anti-slip profile
- Excellent chemical and abrasion resistance
- Designed for high traffic and industrial areas
- Good For Docks, Ramps, Walkways etc
- 100% solids, 2 component
E5820 Oil Stop Epoxy Concrete Primer / Coating For Oil Contamination Areas
From: $50.00- Great for coating over oil contaminated concrete
- Can use as a primer before applying decorative coating systems
- Good as stand alone black colored coating
- Excellent substrate penetration through oil contaminated surfaces
- Excellent adhesion where standard epoxies typically fail
- Long 1 - 2 hour pot life
- High solids, 2 component
E591 Wet Surface Epoxy | Apply Underwater | Cures to 35°F | Concrete – Steel | Floors – ...
From: $120.00- May be applied on wet or under water surfaces
- Cold temperature application down to 35°F
- Self-priming on steel and on most concrete applications
- Long 40-50 POT Life at 75F
- Ideal for marginally prepared and painted surfaces
- Outstanding impact and abrasion
- High film build - Up to 20 mil DFT per coat on horizontal surfaces
- Vertical surfaces to 12 mils
- Excellent coating for manholes
- 100% solids and 0 g/L VOC's
- 3 Colors Available
E650 Non-Skid Epoxy Floor & Deck Low Temp 25°F | OSHA ADA Navy Spec Mil-PRF-24667B
From: $107.00- Heavy duty non-skid resistance for concrete & steel
- Available in regular cure and cold temp formula to 25°F
- Designed for wet areas
- Meets ADA and OSHA requirements for safe co-efficient of friction (COF) when properly applied
- Meets Navy Military Specification Mil-PRF-24667B for Non-Skid Deck Coatings
- Excellent adhesion, abrasion and impact resistance
- Resistant to grease, oil, salt water, alcohol, detergent, gasoline, hydraulic fluid
- Excellent coating for Diamond Plate
- Easy to apply, ready to use non-skid coating
- Comes in 4 colors
E671CL Epoxy Floor Coating | Clear | 100% Solids | For Metallic Pigment and Full Flake & Quartz...
From: $52.00- Clear epoxy great for use with metallic pigments and full flake or quartz broadcast systems
- High Build - 100% Solids Commercial Epoxy
- Good Adhesion 350 psi
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
E700HV Epoxy | Exceptionally Tough | Abrasion & Chemical Resistant | No Topcoat Required
From: $64.00- Saves Money - Eliminates Need for Urethane or Polyaspartic Topcoat
- Extremely Tough D-90 Shore Hardness
- Exceptional Abrasion resistance Only 19 mg loss (Tabor test)
- Excellent Adhesion 420 psi
- Good Chemical Resistance
- Great Looking Very High gloss (80-105 at 60 degrees @ glossmeter)
- 97% Solids Commercial Epoxy
- High build 15-30 mils one coat (53 - 106 sq'/gal)
- Wide Variety of 20 Colors
E707HB High Build 100% Solids Epoxy Floor Coating | 20 Colors
From: $55.00- High Build - 100% Solids Commercial Epoxy
- Long POT Life (working time) 30-50 min
- Excellent Adhesion 450 psi
- Abrasion resistant Only 32 mg loss (Tabor test)
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
- Wide Variety 20 Different Colors
E707LVP High Solids Epoxy Primer & Base Coat | Helps Prevent Outgassing | 20 Colors
From: $54.00- High Solids Commercial Grade Epoxy Primer
- Helps reduce problems from concrete outgassing (air bubbles)
- Long POT Life (working time) 35-55 min
- Excellent Adhesion 430 psi
- Good Chemical Resistance
- Wide Variety 20 Different Colors
GroundWorx SF ESD Static Conductive Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014
From: $960.00- Conductive 2 Part Water Based Thin Film Epoxy Floor Coating
- Conductive range 2.5 x 104 - 3.5 x 107 ohms
- System Resistance (w/ ESD Footware) < 3.5 x 107 (fully compliant) ANSI/ESD STM 97.1
- Warrantied ANSI S20.20 performance
- Meets ANSI/ESD S20.20-2014 (S97.1 and S97.2), DOD 4145.26M, HDBK263A
- Easy to Install
- For Concrete, Wood, VCT Tile Floors
- Use in Electronics Mfg, Assembly, ESD Protected Areas
- 6 Colors. Pewter Gray Color available for immediate shipment
GroundWorx SF ESD Static Dissipative Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-2014
From: $960.00- Static Dissipative 2 Part Water Based Thin Film Epoxy Floor Coating
- Static Dissipative 10e6 to 10e9 ohms
- Warrantied ANSI S20.20 performance
- Meets ANSI/ESD S20.20-2014
- Easy to Install
- For Concrete, Wood, VCT Tile Floors
- 6 Colors.
- Static Dissipative version of Groundworx is special order 4-5 week lead time. Most projects use the Conductive Version of GroundWorx with immediate shipment of Pewter color
GroundWorx Ultra (HB-97.2) ESD Static Conductive Epoxy Primer 100% Solids | Forklift Traffic | ANSI/...
From: $555.00- Static dissipative or conductive high build epoxy electrical protection when used with the GroundWorx Ultra ESD Urethane Topcoat which comes in either dissipative >1.0 x 10e6 ohms or conductive <1.0 x 10e6 ohms electrical resistance, limiting Static Charge Generation to <15 volts
- Great for high traffic, high wear commercial & industrial applications as high build 14 mil ESD system at <$4.00/sq' material cost
- Use on Concrete, Wood and old VCT surfaces
- Moisture tolerant primer
- Excellent adhesion 350 psi
- 100% solids, 0 g/L voc
- Conforms to ESDA, ANSI standard S20.20-2014 when used with GroundWorx Ultra ESD Urethane Topcoat
- Gloss sheen
- 8 standard colors & custom colors available
H20 HyperPRIME Epoxy Quick Cure Bonding Primer | Low Temp 45°F | 3 Hr Recoat
From: $40.00- Excellent Substrate Penetration with superior adhesion 450 psi
- Great for concrete, wood and metal surfaces
- Helps protect Against Coating Damage from Outgassing of Concrete
- Quick Cure With 3 Hour Recoat Time - great for 1 day floor coating systems
- Available in Clear plus 6 Colors
- Water Base, No Offensive odors
- Cold temperature application down to 45F
- Good chemical and Stain Resistance
- Easy Application
HyperBOND Epoxy | Wet Condition Moisture Tolerant | Concrete Floor Coating | Low Temp 40F | 100% Sol...
From: $60.00- Tough, Durable Epoxy Coating
- Outstanding Bonding
- Water Insensitive and Can Be Applied In Wet Conditions
- Withstands up to 9 lbs. of hydrostatic pressure
- Cold temperature application down to 40F
- Long 30-35 min working time
- Resistant to Blushing/Sweating
- Good chemical, impact and abrasion resistance
- High solids 100%
- Available in clear & 13 colors! (Pigment sold separately). In 3 gallon kits only, available pre-colored in 3 colors
HyperCURE Concrete Repair Kit | Flexible 100% Elongation | Quick Cure | Easy To Apply | Recoat 15 &#...
$165.00- Superior Flexibility 100% Elongation
- Outstanding Bonding
- Fast Cure - 15 to 30 min recoat
- Rapid Cure Rate For Same Day System Application
- High D70 Hardness
- High Tensile & Tear Strength
- Very Easy to Use
- Tough, Durable Epoxy Concrete Crack Repair, Hole, Spall and Control Joint Filler
HyperFLEX Epoxy | Flexible Membrane Concrete Wood Steel | 150% Elongation | Low Temp 40°F | 100% Sol...
From: $74.00- Tough, Durable Epoxy Coating and Flexible Membrane
- Very Flexible with Elongation rating 150% @ASTM D-638
- Great for Quick Crack Repair and Control Joint Filler (when mixed with Fumed Silica)
- Can be used as a (1) basecoat for full broadcast floors, (2) flexible membrane, (3) repair gel to fill joints, cracks, & divots
- Cold temperature application down to 40°F
- Concrete & Wood Floors and Countertops
- Superior Flexibility and Outstanding Bonding
- Rapid Cure Rate For Same Day Flake and Solid Color System Application
- When used as membrane or basecoat HyperFLEX cures about 2 hours
- When used for gel repair cures about 10-15 minutes
- Good chemical and abrasion resistance
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 13 colors! (Pigment sold separately)
HyperREZ UV Epoxy Concrete Floor Coating | 45 min Work time | 100% Solids | Ultra Clear Great for Me...
From: $70.00- Tough, durable epoxy floor and countertop coating
- Cold temperature application down to 40F
- High Build Applications up to 32 mils/coat (50 sq'/gal)
- Long Working Time
- Good chemical and abrasion resistance
- UV Resistant
- High gloss appearance
- Designed for high traffic and industrial areas
- High solids 100%
- Withstands up to 9 lbs. of hydrostatic pressure
- Available in clear & 14 colors (Colored Pigment Sold Separately)
MV2112 Moisture Vapor Barrier Primer Epoxy For Concrete Floors | ASTM F3010
From: $105.00- Reduce effects of moisture vapor transmission on concrete floors
- Control moisture vapor emission rates to 20 lb/24hr/1000 sq’ (ASTM F1869) or between 75% and 95% for ASTM F2170
- Superior moisture vapor control
- Class I Vapor Diffusion Retarder with perm rating of <.10
- Primer to protect Polymeric coating systems, vinyl sheets, tile, cementitious overlays, terrazo, wood veneers, and carpet
- 100% solids with 0 voc
- Meets ASTM F3010 for vapor permeance at the recommended thickness
NE253 Novolac Colored Epoxy Acid Solvent Chemical Resistant High Build
From: $55.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Resistant to high concentration acids, some chlorinated solvents incl xylene, MEK
- Resists wide range of chemicals, solvents and acids
- High build for heavy duty traffic projects, chemical troughs and curbs
- Great for tanks and chemical spill areas for cement, masonry or brick
- Excellent adhesion 425 psi
- Quick back in-service, light foot traffic 10-18 hrs
- Selection of 3 color options
- Low voc 47 g/L
NE253SL Novolac Epoxy Colored Slurry Acid Chemical Resistant Floor Coating
From: $55.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Apply to 1/16" thick to resurface traffic, chemical spill areas
- Resists wide range of chemicals, solvents and acids
- Resistant to high concentrations of acids and even some chlorinated solvents incl xylene, MEK
- Excellent adhesion 425 psi
- Quick back in-service with light foot traffic 10-18 hours
- Selection of 3 color options
- Low voc 22 g/L
NE253V Novolac Vertical Wall Colored Epoxy Chemical Resistant Acid Solvent
From: $55.00- Outstanding Spill & Splash Acid, Solvent, Chemical protection
- Resistant to high concentration acids, some chlorinated solvents incl xylene, MEK
- Apply up to 10 mils on vertical walls
- Resists wide range of chemicals, solvents and acids
- Medium build for chemical troughs and curbs
- Great for tanks and chemical spill areas for cement, masonry or brick
- Excellent adhesion 425 psi
- Quick recoat 5-10 hrs
- Selection of 3 color options
- Low voc <40 g/L
NE255P Novolac Epoxy Primer/Sealer Flexible Crack Bridging Chemical Resistant
From: $55.00- Excellent crack bridging, flexible high build primer eliminates need to repair hairline cracks in chemical exposure areas
- Use for priming light to medium duty secondary containment
- Tough, durable coating for surfaces exposed to vehicle traffic
- Outstanding abrasion and impact resistance with only 5 mg loss Taber Abrasion test and 100 inch lbs Gardner Impact Test
- Excellent adhesion 450 psi
- 100% solids, zero voc 0 g/L
NE256 Novolac Clear Epoxy Acid Solvent Chemical Resistant Floor Coating
From: $55.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Exceptional resistance to wide range of chemicals, solvents and acids
- Medium to High build for chemical spill areas, troughs, curbs and tanks
- Use as clear color coating or base for chip/flake or aggregate systems
- Excellent adhesion 400 psi
- Low voc <31 g/L
NE256M Novolac Epoxy Mortar Acid Solvent Chemical Resistant Patch Kit/Resurfacer
From: $83.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Apply at 1/8" to 1/4" to resurface traffic and chemical spill areas
- Used in many chemical immersion projects, curbs, tanks and chemical troughs
- Resists wide range of chemicals, solvents and acids
- Excellent impact and abrasion resistance
- Selection of 4 color options
- Low voc <14 g/L
NE257P Novolac Epoxy Colored Primer Acid Solvent Chemical Resistant Floor Coating
From: $55.00
NE258P Novolac Epoxy Clear Primer Acid Solvent Chemical Resistant Floor Coating
From: $55.00- Excellent primer companion to our NE256 Novolac Clear Epoxy topcoat
- Helps reduce air release generation when applying higher solids novolac topcoats
- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Resists wide range of chemicals, solvents and acids
- Excellent adhesion 365 psi
- Long working time with 1 to 3 hour POT life
NE259G Novolac Epoxy Grout Coat Acid Solvent Chemical Resistant Floor Coating
From: $55.00- Outstanding Spill and Splash Acid, Solvent, Chemical surface protection
- Resists wide range of chemicals, solvents and acids
- Low build epoxy to seal surface of existing mortar overlay system
- Great for topcoating/sealing poxy mortar power trowled or hand trowled systems
- Excellent adhesion 425 psi
- Selection of 3 color options
- Low voc <47 g/L
NE5928 Interior Expansion & Flexible Joint Novolac Chemical Sealant
From: $146.00- Flexible joint filler - Elongation 43.4% at 70F (ASTM D-412)
- Outstanding chemical and impact resistance
- Novolac epoxy urethane hybrid formula
- Excellent adhesion 420 psi
- 100% solids with 0 voc
- Low odor
- Paintable surface
NE5928V Vertical Interior Expansion & Flexible Joint Novolac Chemical Sealant
From: $145.00- Flexible vertical joint filler - Elongation 43.4% at 70F (ASTM D-412)
- No sag formula for vertical interior wall and overhead applications
- Outstanding chemical resistance
- Novolac epoxy and urethane hybrid formula
- Excellent impact resistance
- Good adhesion 380 psi
- 100% solids with 0 voc
- Low odor
- Paintable surface
NP-1 Cove Master Vertical Epoxy Mortar | 100% Solids | High Build | 5 Colors
From: $56.00- Easy construction of vertical cove bases
- 100% Solids Commercial Grade Epoxy
- High build formula
- 5 color options
- Comes as 3 part kit with aggregate or Liquid Only to add your own aggregate or NP1 can also be used as a primer.
UW601 Underwater Concrete Crack Filler Epoxy Paste Repair
$350.00- Make Repairs Underwater or on Wet Surfaces
- Concrete and Masonry
- Both Horizontal & Vertical Repairs
- Good for Cracks up to 1/8" and Thin Build Repairs
- Apply 35F - 90F
- 100% solids with 0 voc
- Low odor
UW602 Underwater Pourable Concrete Crack Filler Epoxy Repair
$325.00- Make Repairs Underwater or on Wet Surfaces
- Concrete, Cement and Masonry
- Both Horizontal & Vertical Repairs
- Good for Larger Cracks and Wide Variety of Repairs
- Easy to Use Pourable Formula
- 100% solids with 0 voc
- Low odor
Copyright 2023 by Exterior Performance Coatings LLC