Call us (630) 675-4509
Show
Filter by
Filter by
1007 Polyurea Coating Fast Set Waterproof Spray | Elastomeric 100% Solids
$7,326.00- 100% Pure Polyurea Waterproof Spray Coating
- Fast 10-30 Sec Set Time - Quick Back In-Service
- Flexible Elastomeric Spray 600%+ Elongation
- Excellent Chemical, Abrasion Impact Resistance
- Unlimited mil/coat & unlimited recoat window
- Use on Concrete, Metal, Wood
- Good for Garages, Marine Enviroments, Secondary Containment, Industrial Applications
3246 Polyurea Flexible Expansion Joint Filler | Exterior Interior | Low Temp -20°F | Elongation 600%...
From: $191.00- Quick 30 Min Back In-Service Joint Repair
- Extremely Flexible 600%+ Elongation for extreme conditions
- Abrasion, Chemical and Fuel Resistant
- Great for Concrete Driveways, Parking Garages, Bridges, Warehouses
- Outdoor control joint & all expansion joints
- 100% Solids, Self leveling
- Apply using High Speed Machine Application and for small projects easy application using twin cartridge kits and 300 ml x 300 ml cartridge gun
- Cold Application Down to -20°F (-26°C)
Hot
5500 Polyaspartic Polyurea Coating Roll Down Low Temp 30°F | 87% Solids
From: $149.00- Beautiful Decorative High Gloss Appearance
- Cold Temperature Application to 30F using Fast Set
- Easy Squeegee/Roller Application
- Waterproof, Aliphatic Resists UV Non-Yellowing
- Indoor & Outdoor Floor and Countertop Projects
- Good In Submerged Service Projects Like Fountains
- Works well on concrete, brick, steel, wood, fiberglass
- Excellent Chemical & Abrasion Resistance
- Highly Adhesive, Flexible & Non-Brittle
- Optional Fast or Slow Set, High Heat & Humidty
- Great For Garage Floors Using Chips & Flakes
- Commercial and Industrial Applications
- Use as Stand Alone System or Topcoat to Epoxy
Hot
6009 Epoxy Floor Coating Industrial & Commercial Low Temp 35°F | 100% Solids | Quick Cure
From: $115.00- Commercial, Industrial, Residential Concrete Floors
- Cold temperature down to 35°F
- Tough - Attractive Looking Epoxy
- Good Chemical, Abrasion, Impact Resistance
- Quick 4 to 7 hour set time
- Self Priming With No Primer Required
- 100% Solids, no VOC, 2 Component
- Clear or Selection of Colors
- Excellent Protection at Lower Cost
6700 Premium ESD Static Dissipative Anti-Static Floor Paint | 9 Colors | ANSI/ESD S20.20-2014
From: $384.00- Static dissipative 10e7 - 10e9 ohms
- Conforms to ANSI/ESD S20.20-2014 when tested according to ANSI/ESD STM7.1
- No hot spots
- Excellent adhesion and color retention
- Good resistance to abrasion, oils and washing
- Use on Concrete, Wood, Metal surfaces
- Interior or exterior use
- Non-hazardous, Non-Flammable, low VOC
- Low gloss sheen
- 9 In-Stock Colors, Custom Colors Available
6700C Premium ESD Static Conductive Anti-Static Floor Paint | 3 Colors | ANSI/ESD S20.20-2014
From: $425.00- Static Conductive 10e3 - 10e6 ohms
- Conforms to ANSI/ESD S20.20-2014 when tested according to ANSI/ESD STM7.1
- No hot spots
- Excellent adhesion and color retention
- Good resistance to abrasion, oils and washing
- Use on Concrete, Wood, Metal surfaces
- Interior or exterior use
- Non-hazardous, Non-Flammable, low VOC
- Low gloss sheen
- 3 Colors Available - Light Gray, Dark Gray, Black
7001 Polyurethane Primer Concrete & Steel | Quick Cure | Exceptional Adhesion | Low 35F Temp
From: $80.00- Concrete & Steel Primer For Epoxy, Urethane, Polyaspartic, Polyurea Coatings
- Cross-links With Polyurea, EPDM Roofing and other Plastic Materials Difficult to Bond to
- Deep Penetrating Exceptional 1200 psi Adhesion
- Superior Corrosion, Abrasion and Water Resistance
- For Use in Submerged Service Applications
- Quick 1 hr recoat (based on temp & humidity)
- Semi-flexible & impact resistance
- Reduced concrete outgassing problems
- Moisture Cured easy to use 1 Component
- Wide application range 35°F - 125°F (1.7°C - 52°C)
- Available in black and non-pigmented clear (h0ney comb color).
800 Slow Set Polyurea Adhesive Sealant & Caulk
From: $146.00- Self Leveling, Tough, Flexible, Sandable, Paintable
- Chemical and Fuel Resistant Polyurea
- Repair Concrete Cracks
- Seals Plastic Connectors and Fittings
- For Metals, Plastics, Fiberglass, Steel, Wood, Urethane, Polyurea, Concrete
- 100% Solids, no VOC, 2 Component
- Option for easy application using twin cartridge kits and 300 ml x 300 ml cartridge gun
830 Fast Set Polyurea Repair | Joint Sealant | Caulk | Adhesive | No Sag Walls | Concrete | Steel | ...
From: $146.00- Tough, Flexible, Fast Set, Sandable, Paintable
- Bonds to Concrete, Steel, Wood, Plastic, Fiberglass, Polyurea, Urethane
- Repair Concrete Floors & Walls - Holds Vertical Bead
- Chemical and Fuel Resistant Polyurea
- Cold weather application down to -20F
- Seal Plastic Connectors, Fittings
- Quick, Easy, Effective Repair of Concrete Cracks
- 3 Set Times Hard in 10 min, 15-20 min, 30-40 min
- 100% Solids, no VOC, 2 Component
- Option for easy application using twin cartridge kits and 300 ml x 300 ml cartridge gun
AM1016 Anti-Microbial Mildew Resistant Anti-Slip Epoxy Floor Coating – 3 Gal Kit
From: $210.00- Adds slip resistant finish to concrete floors
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Good for surfaces subject to bare foot traffic
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical and abrasion resistance
- Wide selection clear plus 20 colors
- Water base
AM5015 Anti-Microbial Mildew Resistant Epoxy Primer WB
From: $94.00- Versatile epoxy primer for concrete, masonry, wood
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Available 20 Colors To Match Topcoat
- Excellent primer for epoxy, polyaspartic, urethane
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical & abrasion resistance
- Water base
AM707HB Anti-Microbial Mildew Resistant Epoxy Floor Coating | 100% Solids
From: $162.00- High Build - 100% Solids Commercial Epoxy
- Anti-Microbial prevents growth of micro-organisms
- Resists growth of surface mold, mildew, fungus and helps prevent odors that can result
- Long POT Life (working time) 30-50 min
- Excellent Adhesion 450 psi
- Abrasion resistant Only 32 mg loss (Tabor test)
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
- Wide Variety of 20 Different Colors
E-Poly Pigment For All Floorguard Epoxy & Polyaspartic Coatings | 13 Colors
From: $52.00- Universal E-Poly Pigment Designed to Color All Epoxy & Polyaspartic Coatings manufactured by Floorguard Products
- Add a Beautiful Decorative Color to Your Epoxy Project
- 13 Different Colors to Choose From!
- Sold in Quart Containers - Typically colors 3-5 Gallons When Mixed Into Clear Epoxy or Polyaspartic
- Pigment can be Pre-mixed into Floorguard Epoxy & Polyaspasrtic Coatings on all orders 60 gallons or more with 4-7 days lead time (when ordered in 10 or 15 gallon kits as appropriate)
E1015V Vertical Wall Epoxy Coating & Primer to 8 Mils No Sag | 11 Colors
From: $50.00- No sagging on vertical walls up to 8 mils per coat
- Good for priming or coating concrete, wood or masonry.
- Good chemical and abrasion resistance
- Long 1 - 1.5 hour pot life
- Excellent adhesion 425 psi @elcometer
- Wide selection of 11 color options
- Water base
E1016 Anti-Slip Epoxy Concrete Floor Coating – 3 Gal Kit
From: $196.00- Adds a slip resistant finish to concrete floors
- Good for use on surfaces subject to bare foot traffic
- Long 1 - 1.5 hour pot life
- Excellent adhesion
- Good chemical and abrasion resistance
- Wide selection of clear plus 20 color options
- Water base
E105M Epoxy Mortar Concrete Resurfacer & Patch Kit
From: $66.00- Economical Easy resurfacing old and damaged concrete floors
- Compressive Strength 8,400 psi ASTM D695
- Heat Deflection Temp 131.7F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- 100% solids epoxy
- Comes complete with epoxy & aggregate
- Selection of 5 color options
- Application temp range 55°F to 90°F
E110M Epoxy Mortar Concrete Premium Resurfacer & Patch Kit
From: $73.00- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- 10% greater coverage/unit vs E105M Epoxy Mortar
- Compressive Strength 11,150 psi ASTM D695
- Heat Deflection Temp 158.9F ASTM D648
- High Build Resurfacing 1/8" to 1"
- Spot Patching up to 2" - 3" thick
- Long 30-40 min POT Life
- 100% solids epoxy
- Comes complete with epoxy and aggregate
- Selection of 5 color options
- Application temp range 55°F to 90°F
E126CW Cold Weather Epoxy Mortar Concrete Resurfacer & Patch Kit 35°F to 80°F
From: $71.00- Great for Cold Weather & Cold Storage Facilities
- Application range 35°F to 80°F
- Easy resurfacing old and damaged concrete floors
- Premium Tough, Durable, Chemical Resistant Protection
- Compressive Strength 11,284 psi ASTM D695
- Heat Deflection Temp 149.9F ASTM D648
- High Build Resurfacing 1/8" to 1/4"
- Patching up to 2" thick
- 100% solids epoxy
- Comes complete with epoxy and aggregate
- Selection of 5 color option
E130A Oil Contaminated Concrete & Asphalt Epoxy Mortar Patch Kit/Resurfacer
From: $66.00- Great for patching and repairing oil contaminated and damaged concrete
- Can be used to patch and repair asphalt surfaces
- Can be applied up to 1/8" one application
- Crack. holes and general surface repairs
- Excellent abrasion and impact resistance
- 100% solids
- Easy to Use 3 part kit Includes Silica Sand or Liquid Only
E139FL Flexible Epoxy Primer & Floor Coating | 60% Elongation | 100% Solids | Indoor & Out...
From: $65.00- Exceptionally flexible epoxy with 60% elongation
- High Build up to 50 mils thick per coat
- 100% Solids Commercial Epoxy
- Excellent Adhesion 450 psi
- Tough Abrasion resistant Only 6 mg loss (Tabor test) and 160 inch lbs Gardner variable impact test
- For use with broadcast systems and as flexible membrane primer
- Wide Variety of 15 Colors
E15M Epoxy Mastic Steel Primer DTM & Concrete Coating | Chemical Resistant | Low Temp 25F
From: $95.00- High solids DTM (direct-to-metal) chemical resistant steel primer or finish coat to steel and concrete
- Self priming to steel including tight rust
- Apply Vertical Surfaces to 8 mils DFT Steel & Concrete
- Great primer for use with our E1500HN (horizontal) and E555VN (vertical) Novolac Chemical Resistant Epoxies
- USDA Approved
- Tight film, low permeability.
- Exceptional adhesion Exceeds 500 psi
- Excellent impact resistance 90 in lb
- Excellent abrasion resistance CS 17 Wheel, 1000 cycles, 1000 g Load 21 mg loss
- Excellent against rust “undercutting”
- Easy to apply brush, roll and spray
- Low temp cure version to 25°F
- Available 13 colors
E183HB Epoxy Floor Coating High Build | Quick Back In-Service | Abrasion & Chemical Resistant |...
From: $324.00- High Build - Impact & Chemical Resistant
- Quick back in-service light foot traffic 8-14 hrs
- Full chemical resistance only 3 days
- Excellent Adhesion 450 psi
- Abrasion resistant Only 23 mg loss (Tabor test)
- Excellent Chemical Resistance
- High build apply 10 to 20 mils one coat (80 - 160 sq'/gal)
- Wide Variety of 19 Different Colors
E322HW High-Gloss Aliphatic Urethane Abrasion & Chemical Resistant Low Temp 45°F
From: $60.00- Outstanding durability with impact resistance of 160 in lb (Gardner Impact test)
- Cold temperature application down to 45°F
- Excellent abrasion resistance Only 22 mg loss (Tabor Abrasion test) Reduced to 10 mg loss using our High Wear 325 additive
- Excellent Chemical Resistance
- Aliphatic, UV Stable and will not yellow
- Easy to Use with Long 2-4 Hour Pot Life
- Great for both Indoor and Outdoor Concrete Floor Projects
- Comes in wide Variety of Clear and 18 Different Colors
- Solvent Based - Excellent adhesion
E352P Hi-Gloss Polyester Polyurethane Floor Coating | Chemical Abrasion Resistant | Exterior Interio...
From: $205.00- Great Interior & Exterior Horizontal Concrete & Steel Protection
- Exceptional Exterior Durability
- Excellent weather resistance
- Non-chalking and non-yellowing with excellent gloss and color retention
- Extremely tough, yet flexible
- A tile-like finish.
- Easy to clean
- Excellent chemical and stain resistance
- Highly resistant to abrasion and impact
- Outstanding wearing properties
- Handles up to 250°F Dry Service
- Long 4 hour POT life @ 75ºF
- Available in clear and 11 colors
E370P Hi-Gloss Hi Build Polyurethane | Non-Yellowing | For Vertical Concrete and Steel | Interior &#...
From: $118.00- Great Interior & Exterior Vertical Concrete & Steel Protection
- Exceptional Exterior Durability
- High solids
- Tile-like finish.
- Easy to clean
- Good chemical and stain resistance
- Highly resistant to abrasion and impact.
- Excellent gloss and color retention to UV exposure
- Pass 2500 hrs - QUV Accelerated Weathering ASTM D4587
- Outstanding wearing properties.
- Non-chalking and non-yellowing
- High film build
- Handles up to 300°F Dry Service
- Long 4-6 hour POT life @ 75ºF
- Available in clear and 21 colors
E5015 Epoxy Primer WB Coating | Concrete Wood Masonry | 20 Colors
From: $51.00- Versatile product good on concrete, masonry, wood surfaces
- Excellent as primer for epoxy, polyaspartic and urethane coating systems
- Helps prevent concrete outgassing problems when used as primer
- Available in Clear and 20 Colors To Match With Topcoat
- Long 1 - 1.5 hour pot life
- Excellent adhesion 425 psi
- Good chemical and abrasion resistance
- Water base
E505V Vertical Wall Epoxy Concrete Block Filler to 20 Mils No Sag | 11 Colors
From: $117.00- No sagging on vertical concrete and cement block walls up to 20 mils per coat
- Great epoxy block filler
- Good chemical and abrasion resistance
- Long 45 - 90 min pot life
- Excellent adhesion 420 psi @elcometer
- Wide selection of 11 color options
- 100% solids, very low voc
E5820 Oil Stop Epoxy Concrete Primer / Coating For Oil Contamination Areas
From: $50.00- Great for coating over oil contaminated concrete
- Can use as a primer before applying decorative coating systems
- Good as stand alone black colored coating
- Excellent substrate penetration through oil contaminated surfaces
- Excellent adhesion where standard epoxies typically fail
- Long 1 - 2 hour pot life
- High solids, 2 component
E650 Non-Skid Epoxy Floor & Deck Low Temp 25°F | OSHA ADA Navy Spec Mil-PRF-24667B
From: $107.00- Heavy duty non-skid resistance for concrete & steel
- Available in regular cure and cold temp formula to 25°F
- Designed for wet areas
- Meets ADA and OSHA requirements for safe co-efficient of friction (COF) when properly applied
- Meets Navy Military Specification Mil-PRF-24667B for Non-Skid Deck Coatings
- Excellent adhesion, abrasion and impact resistance
- Resistant to grease, oil, salt water, alcohol, detergent, gasoline, hydraulic fluid
- Excellent coating for Diamond Plate
- Easy to apply, ready to use non-skid coating
- Comes in 4 colors
E700HV Epoxy | Exceptionally Tough | Abrasion & Chemical Resistant | No Topcoat Required
From: $64.00- Saves Money - Eliminates Need for Urethane or Polyaspartic Topcoat
- Extremely Tough D-90 Shore Hardness
- Exceptional Abrasion resistance Only 19 mg loss (Tabor test)
- Excellent Adhesion 420 psi
- Good Chemical Resistance
- Great Looking Very High gloss (80-105 at 60 degrees @ glossmeter)
- 97% Solids Commercial Epoxy
- High build 15-30 mils one coat (53 - 106 sq'/gal)
- Wide Variety of 20 Colors
E707HB High Build 100% Solids Epoxy Floor Coating | 20 Colors
From: $55.00- High Build - 100% Solids Commercial Epoxy
- Long POT Life (working time) 30-50 min
- Excellent Adhesion 450 psi
- Abrasion resistant Only 32 mg loss (Tabor test)
- Good Chemical Resistance
- High build 12-30 mils one coat (53 - 130 sq'/gal)
- Wide Variety 20 Different Colors
E707LVP High Solids Epoxy Primer & Base Coat | Helps Prevent Outgassing | 20 Colors
From: $54.00- High Solids Commercial Grade Epoxy Primer
- Helps reduce problems from concrete outgassing (air bubbles)
- Long POT Life (working time) 35-55 min
- Excellent Adhesion 430 psi
- Good Chemical Resistance
- Wide Variety 20 Different Colors
E811FP Acrylic Self Plasticizing Roof Coating | Monolithic Flexible Membrane
From: $240.00- Exceptionally tough, flexible 1 part acrylic roof coating
- Excellent adhesion for Concrete, Wood and Metal
- Tough surface, holds up to normal foot traffic
- Excellent weathering pass ASTM G93 for 9,000 hrs
- Excellent UV stability
- Resists growth of mildew
- Excellent flexibility 415% Elongation
- Resists cracking, splitting with building movement
- Available in 6 colors
- Underwriters Laboratories (UL) Tested & Certified
E812 Acrylic Self Plasticizing Roof Coating | Monolithic Flexible Membrane
From: $225.00- Tough, flexible budget friendly 1 part acrylic roof coating
- Good adhesion for Concrete, Wood and Metal
- Tough surface, holds up to normal foot traffic
- Excellent weathering pass ASTM G93 for 9,000 hrs
- Excellent UV stability
- Resists growth of mildew
- Good flexibility >200% Elongation
- Resists cracking, splitting with building movement
- Available in 6 colors
E814CP Co-Polymer Flat Roof Coating | 11 Color | Flexible | Waterproof
From: $71.00- Exceptionally tough, flexible 1 part SEBS Based waterproof coating
- Great for both Flat & Sloped Roofs
- Excellent adhesion EPDM, APP, TPO, Hypalon, BUR, Fiberglass, PVC, Polyurethane Foam, Concrete, Wood, Metal
- Excellent waterproof with E96 Vapor Transmission Class I 0.025 perms and Water Absorption 0.04%
- Excellent weathering
- Excellent UV stability
- Good resistance to dirt pickup
- Excellent low temp flexibility 500%+ Elongation
- Resists mildew and fungi growth
- Good resistance to Alkalis and acids
- Available in 11 Colors
- Underwriters Laboratories (UL) Tested & Certified
- Class A Fire Rated
E814R Co-Polymer Liquid Rubber Roof Walkway Coating | Slip Resistant
From: $76.00- Exceptionally tough, durable one part waterproof roof walkway
- Offers excellent anti-slip walking surface
- Excellent adhesion EPDM, APP, TPO, Hypalon, Concrete, Wood, Metal
- Available in 12 colors
- Excellent waterproof with E96 Vapor Transmission Class I 0.025 perms and Water Absorption 0.04%
- Excellent weathering
- Excellent UV stability
- Good resistance to dirt pickup
- Excellent low temp flexibility with 500%+ Elongation
- Resists mildew and fungi growth
- Good resistance to Alkalis and acids
ESD Conductive Anti-Fatigue Cushioned Floor Mat Protects Anti-Static Floors | Meets ANSI 20.20
From: $335.00- Conductive 1/2" cushioned Anti-Fatigue Floor Mat
- Resistance point to point measures 1x10e5 – 1x10e7 ohms
- Dissipative cushioned under layer
- Smooth surface
- Beveled edges
- Equipped with 10mm female ground socket
- 10’ grounding cord
- Made in USA
- Protects ESD Flooring & ESD Paint Investment
- Comes in 3 sizes
ESD Conductive Floor Runner Protects Anti-Static Floors | Meets ANSI 20.20 | 48″W x 75’L
$3,400.00- Protects ESD Flooring & ESD Paint Investment
- Solid Flat Surface Impervious to Damage from Chair Casters
- Great for Long Workbenches or easy cut to size with utility razor knife: 48"W x 75'L
- Conductive Anti-Static Protection
- Continuous and Permanent Path-to-Ground
- Lifetime Warranty ANSI S20.20 & ANSI S7.1-2005
- Electrical properties are warranted for the lifetime of the mat
- Resistance measures 10e4 – 10e6 ohms per ANSI/ESD S7.1-2005
- Compliant to ANSI/ESD S20.20
- Solid single layer is .090" (2.29 mm) thick
- Low outgassing and low VOC
- Made in the USA
ESD Conductive Vinyl Chair Floor Mat Protects Anti-Static Floors | Meets ANSI 20.20
From: $200.00- Protects ESD Flooring & ESD Paint Investment
- Solid Flat Surface Impervious to Damage from Chair Casters
- Conductive Anti-Static Protection
- Continuous and Permanent Path-to-Ground
- Lifetime Warranty ANSI S20.20 & ANSI S7.1-2005
- Comes in 3 sizes
- Electrical properties are warranted for the lifetime of the mat
- Resistance measures 10e4 – 10e6 ohms per ANSI/ESD S7.1-2005
- Compliant to ANSI/ESD S20.20
- Solid single layer is .090" (2.29 mm) thick
- Low outgassing and low VOC
- Made in the USA
ESD Vinyl Workspace & Chair Mat For Anti-Static Floors | Conductive ANSI 20.20 | Slip Resistant...
From: $130.00- Protects ESD Flooring & ESD Paint Investment
- Impervious to Damage from Chair Casters
- Great for workstations with Slip Resistant Textured Surface
- Conductive Anti-Static Protection
- Continuous and Permanent Path-to-Ground
- Lifetime Warranty ANSI S20.20 & ANSI S7.1-2005
- Comes in 2 sizes (36"x60" and 48"x72")
EXPERT Semi-Solid Wood Stain & Sealer | Oil Based Deep Penetrating | Extreme Climate Apply -10°...
From: $75.00- Provides a rich color while allowing the natural grain to still come through
- Deep Penetrating Oil Through Entire Wood For Exceptional Protection
- Great Protection for medium to heavy foot traffic decks
- Prevents Drying Out which causes warping and cracking
- Non-Film Forming Won't chip, crack or peel
- Mildew & UV Resistant - Maintains Color
- Water Shedding
- Extreme Climate Can Apply -10°F to 110°F
- Ultra Low VOC < 7 g/L
- Rain-safe soon as 1 hour after applied to fences
- Easy one coat application
- Easy Maintenance - Recoat without stripping, sanding or scraping
- 9 Semi-Solid Color Options
GroundWorx Basics (SF) ESD Static Conductive Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-201...
From: $960.00- Conductive 2 Part Water Based Thin Film Epoxy Floor Coating
- Conductive range 2.5 x 104 - 3.5 x 107 ohms
- System Resistance (w/ ESD Footware) < 3.5 x 107 (fully compliant) ANSI/ESD STM 97.1
- Warrantied ANSI S20.20 performance
- Meets ANSI/ESD S20.20-2014 (S97.1 and S97.2), DOD 4145.26M, HDBK263A
- Easy to Install
- For Concrete, Wood, VCT Tile Floors
- Use in Electronics Mfg, Assembly, ESD Protected Areas
- 6 Colors. Pewter Gray Color available for immediate shipment
GroundWorx Basics (SF) ESD Static Dissipative Epoxy Floor Coating | Water Based | ANSI/ESD S20.20-20...
From: $960.00- Static Dissipative 2 Part Water Based Thin Film Epoxy Floor Coating
- Static Dissipative 10e6 to 10e9 ohms
- Warrantied ANSI S20.20 performance
- Meets ANSI/ESD S20.20-2014
- Easy to Install
- For Concrete, Wood, VCT Tile Floors
- 6 Colors.
- Static Dissipative version of Groundworx is special order 4-5 week lead time. Most projects use the Conductive Version of GroundWorx with immediate shipment of Pewter color
GroundWorx Ultra (HB-97.2) ESD Static Conductive Epoxy Primer 100% Solids | Forklift Traffic | ANSI/...
From: $555.00- Static dissipative or conductive high build epoxy electrical protection when used with the GroundWorx Ultra ESD Urethane Topcoat which comes in either dissipative >1.0 x 10e6 ohms or conductive <1.0 x 10e6 ohms electrical resistance, limiting Static Charge Generation to <15 volts
- Great for high traffic, high wear commercial & industrial applications as high build 14 mil ESD system at <$4.00/sq' material cost
- Use on Concrete, Wood and old VCT surfaces
- Moisture tolerant primer
- Excellent adhesion 350 psi
- 100% solids, 0 g/L voc
- Conforms to ESDA, ANSI standard S20.20-2014 when used with GroundWorx Ultra ESD Urethane Topcoat
- Gloss sheen
- 8 standard colors & custom colors available
GroundWorx Ultra (HB-97.2) ESD Urethane Top Coat | Static Dissipative or Conductive | ANSI S20.20-20...
From: $1,350.00- Optional Static conductive <1.0 x 10e6 ohms or Dissipative >1.0 x 10e6 ohms and <1.0 x 10e9 high performance electrical protection, limiting Static Charge Generation to <15 volts
- Great for high traffic, high wear commercial & industrial applications as high build 14 mil ESD system at <$4.00/sq' material cost
- Conforms to ESDA, ANSI standard S20.20-2014 when used with GroundWorx Ultra ESD Epoxy Primer
- Use on Concrete, Wood and old VCT surfaces
- Tough surface: impact resistance 140 psi and tabor abrasion test 25 mg loss
- Surface: Anti-slip, ROHS compliant
- No wax required – easy to keep clean
- Satin to Semi-gloss sheen
- 8 standard colors & custom colors available
- Each 2 gallon kit includes 8 oz anti-slip clear glass beads for improved safety in wet conditions
H20 HyperPRIME Epoxy Quick Cure Bonding Primer | Low Temp 45°F | 3 Hr Recoat
From: $40.00- Excellent Substrate Penetration with superior adhesion 450 psi
- Great for concrete, wood and metal surfaces
- Helps protect Against Coating Damage from Outgassing of Concrete
- Quick Cure With 3 Hour Recoat Time - great for 1 day floor coating systems
- Available in Clear plus 6 Colors
- Water Base, No Offensive odors
- Cold temperature application down to 45F
- Good chemical and Stain Resistance
- Easy Application
NE3770 Novolac Chemical Resistant Epoxy | High Heat Exposure to 225˚F | Meets USDA Criterea | 100% S...
From: $315.00- High Heat Resistance to 225˚F+
- Strong Chemical Resistance to wide range of chemicals including 70% Sulfuric Acid 90 days+ and 50% Sodium Hydroxide 30 Days
- Great spill, splash and secondary containment chemical spill areas for cement, masonry or brick
- Meets USDA criteria
- High Strength
- 100% solids high build
- Low Odor
- Superior Adhesion
- Selection of clear and 4 color options
NP-1 Cove Master Vertical Epoxy Mortar | 100% Solids | High Build | 5 Colors
From: $56.00- Easy construction of vertical cove bases
- 100% Solids Commercial Grade Epoxy
- High build formula
- 5 color options
- Comes as 3 part kit with aggregate or Liquid Only to add your own aggregate or NP1 can also be used as a primer.
Pigment Color For 5500 Polyaspartic Coating
$64.00- Pigment Designed to Color the 5500 Polyaspartic made by ASTC Polymers
- Add a Beautiful Decorative Color to Your 5500 Polyaspartic Project
- 7 Different Colors to Choose From!
- Sold in Quart Containers - Colors 2-3 Gallons When Mixed Into Clear 5500
Pigment For E344QC, E444X, E449 and E450SF Polyaspartic
From: $45.00- Pigment Designed to Color E344QC, E444X, E449 and E450SF Polyaspartic Coating
- Add a Beautiful Decorative Color to Your Polyaspartic Project
- 13 Different Colors to Choose From!
- Easy mixing using a Jiffy style mixer
Traffic-Lok 100% Acrylic Traffic and Line Marking Paint | Premium Waterborne | Concrete Masonry Asph...
From: $44.00- Flexible and Durable- Will Not Crack
- Easy to Apply
- Great for concrete, asphalt, galvanized metal, aluminum and previously painted surfaces
- Environmentally Safe
- Requires No Thinning-Pre-Stained
- Safe for Interior and Exterior Applications
- 6 color options
Copyright 2024 by Exterior Performance Coatings LLC